Study guide
1.2 Ton of Refrigeration and Temperature Ranges
RETA Certified Assistant Refrigeration Operator Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Refrigeration Fundamentals
1.1 Heat, Temperature, and Pressure 1.2 Ton of Refrigeration and Temperature Ranges 1.3 Superheat and Subcooling
2 Chapter 2: Refrigeration Cycle
2.1 Vapor-Compression Cycle Flow and Components 2.2 Heat Rejection Balance and Expansion Devices 2.3 Cascade Systems and Intercoolers
3 Chapter 3: Properties of Refrigerants
3.1 Ammonia (R-717) Basics and Physical Properties 3.2 Ammonia Hazards and Flammability 3.3 Industrial Comparison and Efficiency
4 Chapter 4: Saturated Refrigerant Tables
4.1 Saturated Ammonia P-T Tables
5 Chapter 5: Types of Compressors
5.1 Industrial Compressor Types
6 Chapter 6: Operation and Maintenance of Compressors
6.1 Compressor Construction and Unloaders 6.2 Compression Ratio and Volumetric Efficiency 6.3 Compressor Startup and Operating Parameters 6.4 Compressor Troubleshooting and Slugging
7 Chapter 7: Lubrication
7.1 Lubrication Principles and Oil Types 7.2 Oil Separators and Net Oil Pressure 7.3 Low-Side Oil Logging and Management 7.4 Safe Oil Draining and Charging Procedures
8 Chapter 8: Evaporators and Cooling Units
8.1 DX vs Flooded Evaporators 8.2 TXV Behavior and Control 8.3 Defrost Systems and Evaporator Maintenance
9 Chapter 9: Condensers and High-Pressure Receivers
9.1 Condenser Types and Operation 9.2 High-Pressure Receivers and King Valves 9.3 Safety Relief Valves and Charging
10 Chapter 10: Purging
10.1 Non-Condensable Gases and Ingress 10.2 Purger Operation and Verification
11 Chapter 11: Safety, Hazards, and Prevention
11.1 Regulatory Oversight: OSHA PSM and EPA RMP 11.2 Industry Codes: IIAR Standards 11.3 Ammonia Exposure Limits and First Aid 11.4 Engine Room Safety Systems
1.2 Ton of Refrigeration and Temperature Ranges
Key Takeaways Explain This Topic AI
One standard Ton of Refrigeration (TR) is defined as the heat transfer rate required to melt 2,000 pounds of ice at 32°F in 24 hours.
One ton of refrigeration is equivalent to 288,000 Btu per day, 12,000 Btu per hour, or 200 Btu per minute.
Industrial cooler systems typically maintain room temperatures of 35°F to 45°F, using single-stage compression.
Industrial freezer systems typically maintain room temperatures of 0°F to -20°F, and blast freezers operate between -30°F and -50°F.
Blast freezers require low-temperature evaporators and two-stage booster compression due to the high compression ratio and low suction pressure.
Last updated: July 2026
Understanding the Ton of Refrigeration
In industrial refrigeration, system capacity is rarely expressed in British Thermal Units (Btus) because the numbers would be impractically large. Instead, the industry uses a unit called the Ton of Refrigeration (TR) . This term originated in the late 19th century when ice harvesting was transitioning to mechanical refrigeration. To convince ice-house owners to purchase refrigeration machines, manufacturers rated their equipment based on how many tons of ice it could replace.
The Physics and Math of a Standard Ton
A standard ton of refrigeration is defined as the amount of heat transfer required to melt one ton (2,000 lbs) of pure ice at 32°F to liquid water at 32°F during a 24-hour period.
To calculate this value, we use the latent heat of fusion of ice, which is 144 Btu/lb : Total Heat removed = 2 , 000 lbs of ice × 144 Btu/lb = 288 , 000 Btus \text{Total Heat removed} = 2,000\text{ lbs of ice} \times 144\text{ Btu/lb} = 288,000\text{ Btus} Total Heat removed = 2 , 000 lbs of ice × 144 Btu/lb = 288 , 000 Btus
Since this process takes place over 24 hours, we can calculate the hourly and minute heat transfer rates:
Daily Capacity: 288 , 000 Btu/day 288,000\text{ Btu/day} 288 , 000 Btu/day
Hourly Capacity: 288 , 000 Btu 24 hours = 12 , 000 Btu/hr \frac{288,000\text{ Btu}}{24\text{ hours}} = 12,000\text{ Btu/hr} 24 hours 288 , 000 Btu = 12 , 000 Btu/hr
Minute Capacity: 12 , 000 Btu 60 minutes = 200 Btu/min \frac{12,000\text{ Btu}}{60\text{ minutes}} = 200\text{ Btu/min} 60 minutes 12 , 000 Btu = 200 Btu/min
These three numbers are critical for the CARO exam:
- 1 Ton of Refrigeration = 288,000 Btu/24hr
- 1 Ton of Refrigeration = 12,000 Btu/hr
- 1 Ton of Refrigeration = 200 Btu/min
- Calculations: Heat Load to Refrigeration Capacity
An operator must be able to convert heat loads (heat that must be removed) to refrigeration capacity to evaluate if system components (like compressors and evaporators) are operating within their design parameters.
Conversion Formulas
To convert a heat load in Btus per hour to tons of refrigeration: Tons of Refrigeration = Heat Load (Btu/hr) 12 , 000 Btu/hr/ton \text{Tons of Refrigeration} = \frac{\text{Heat Load (Btu/hr)}}{12,000\text{ Btu/hr/ton}} Tons of Refrigeration = 12 , 000 Btu/hr/ton Heat Load (Btu/hr)
To convert a heat load in Btus per minute to tons of refrigeration: Tons of Refrigeration = Heat Load (Btu/min) 200 Btu/min/ton \text{Tons of Refrigeration} = \frac{\text{Heat Load (Btu/min)}}{200\text{ Btu/min/ton}} Tons of Refrigeration = 200 Btu/min/ton Heat Load (Btu/min)
Worked Example 1: Calculating System Capacity from Hourly Heat Load
An industrial glycol chiller is removing heat from a food processing line at a rate of 780,000 Btu/hr. What is the equivalent refrigeration capacity in tons?
Identify the formula: Tons = Heat Load (Btu/hr) 12 , 000 \text{Tons} = \frac{\text{Heat Load (Btu/hr)}}{12,000} Tons = 12 , 000 Heat Load (Btu/hr)
Substitute the values: Tons = 780 , 000 12 , 000 \text{Tons} = \frac{780,000}{12,000} Tons = 12 , 000 780 , 000
Solve: Tons = 65 TR \text{Tons} = 65\text{ TR} Tons = 65 TR
The chiller is operating at a capacity of 65 tons of refrigeration.
Worked Example 2: Calculating System Capacity from Minute Heat Load
A low-temperature ammonia evaporator is absorbing heat at a rate of 4,800 Btu/min. What is the refrigeration capacity?
Identify the formula: Tons = Heat Load (Btu/min) 200 \text{Tons} = \frac{\text{Heat Load (Btu/min)}}{200} Tons = 200 Heat Load (Btu/min)
- Substitute the values: Tons = 4 , 800 200 \text{Tons} = \frac{4,800}{200} Tons = 200 4 , 800
- Solve: Tons = 24 TR \text{Tons} = 24\text{ TR} Tons = 24 TR
The evaporator is absorbing 24 tons of refrigeration.
Worked Example 3: Finding Required Ice Production
If a processing plant has an ammonia system rated at 150 tons, how many pounds of 32°F ice could this system theoretically produce from 32°F water in 24 hours?
Recall that 1 ton of refrigeration = melting/freezing 2,000 lbs of ice per day.
Apply the ratio: Pounds of ice per day = Refrigeration Capacity (Tons) × 2 , 000 lbs/ton \text{Pounds of ice per day} = \text{Refrigeration Capacity (Tons)} \times 2,000\text{ lbs/ton} Pounds of ice per day = Refrigeration Capacity (Tons) × 2 , 000 lbs/ton Pounds of ice per day = 150 × 2 , 000 = 300 , 000 lbs of ice \text{Pounds of ice per day} = 150 \times 2,000 = 300,000\text{ lbs of ice} Pounds of ice per day = 150 × 2 , 000 = 300 , 000 lbs of ice
The system can freeze 300,000 lbs (150 tons) of ice in 24 hours.
Industrial Temperature Ranges
Ammonia systems are designed differently depending on the temperature range of the space or process they serve. In industrial facilities, these are typically grouped into three main categories: Coolers, Freezers, and Blast Freezers.
- 1. Coolers (High-Temperature Refrigeration)
- Operating Range: 35°F to 45°F (1.7°C to 7.2°C)
- Typical Evaporator Temperature: 20°F to 30°F (to maintain temperature difference for heat transfer)
Common Applications: Produce storage rooms, loading docks, meat cutting rooms, and glycol jacket cooling.
Operator Considerations: Since the room temperature is above freezing (32°F), moisture does not freeze on the product, but frost will still form on evaporator coils if the coil temperature is below 32°F. Defrost cycles are still required, though they can often be accomplished using room air (air defrost).
- 2. Freezers (Medium/Low-Temperature Refrigeration)
- Operating Range: 0°F to -20°F (-17.8°C to -28.9°C)
- Typical Evaporator Temperature: -10°F to -30°F
Common Applications: Frozen food storage warehouses, ice cream storage facilities, and frozen distribution centers.
Operator Considerations: At these temperatures, moisture in the air will freeze on contact with the evaporator coils, forming ice that acts as an insulator and restricts airflow. Active defrost (such as hot gas defrost or water defrost) is critical to maintain heat transfer efficiency.
- 3. Blast Freezers (Ultra-Low-Temperature Refrigeration)
- Operating Range: -30°F to -50°F (-34.4°C to -45.6°C)
- Typical Evaporator Temperature: -40°F to -60°F
Common Applications: Quick-freezing of poultry, seafood, beef, or prepared meals immediately after processing. Fast freezing forms small ice crystals, preserving product texture and quality.
Operator Considerations: These systems operate at very low pressures, often in a vacuum (e.g., at -40°F, ammonia saturates at -10.9 in. Hg vacuum). Air and moisture infiltration are major concerns. Blast freezers require multi-stage compression systems (booster systems) to manage the high compression ratios efficiently.
Summary of Temperature Ranges
- Facility Type Room Temp Range Typical Evaporator Temp Primary Defrost Method Compression Stage
- Cooler 35°F to 45°F 20°F to 30°F Off-cycle / Air Defrost Single Stage
- Freezer 0°F to -20°F -10°F to -30°F Hot Gas / Electric Single Stage or Two-Stage
- Blast Freezer -30°F to -50°F -40°F to -60°F Hot Gas / Water Two-Stage (Booster)
- Two-Stage Compression in Low-Temperature Applications
For systems operating in freezer and blast freezer ranges (suction temperatures below -10°F), the compression ratio becomes very high if compressing directly to standard condensing pressure (typically 120 psig to 180 psig). High compression ratios lead to low volumetric efficiency and extremely high discharge temperatures that break down lubrication oil. To solve this, industrial systems use two-stage compression . A booster compressor handles the low-stage compression (from low evaporator pressure to an intermediate pressure), and a high-stage compressor handles the final compression (from intermediate pressure to condensing pressure). An intercooler cooling vessel is placed between the stages to desuperheat the booster discharge gas and cool the liquid going to the low-temperature evaporators, which significantly increases overall system efficiency.