Study guide
14.3 Hand Expansion Valves and DX Coil Distribution
RETA CIRO Certified Industrial Refrigeration Operator Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Current Exam Facts 1.2 Test-Day Tools, On-Screen References, and Calculators 1.3 CIRO vs CARO and the RETA Credential Path
2 IIAR and ASHRAE Standards
2.1 IIAR 2 and ASHRAE 15 Machinery-Room Design 2.2 IIAR 6 Inspection, Testing, and Maintenance 2.3 IIAR 7 Operating Procedures and IIAR 9 Existing Systems
3 OSHA Process Safety Management
3.1 PSM Applicability and the 14 Elements 3.2 Process Safety Information 3.3 Process Hazard Analysis 3.4 Operating Procedures, Training, Contractors, and PSSR
4 Integrity, Change, and Emergency Programs
4.1 Mechanical Integrity and Pressure-Relief Valves 4.2 Hot Work and Management of Change 4.3 Incident Investigation and Compliance Audits 4.4 Emergency Planning, EPA RMP, and the General Duty Clause
5 Ammonia Hazards and Machinery-Room Safety
5.1 Ammonia Properties, SDS, and Exposure Limits 5.2 Detection, Ventilation, and Emergency Shutdown 5.3 Eyewash, PPE, Materials Compatibility, and ASME B31.5 Piping
6 Three-Phase Motors and Starting
6.1 Three-Phase Motors, Nameplates, and FLA 6.2 Wye-Delta and Reduced-Voltage Starting 6.3 Voltage Unbalance 6.4 Single-Phasing, Rotation Checks, and Screw Compressors
7 Ladder Diagrams, VFDs, and Power
7.1 Ladder Diagrams, Seal-In Circuits, and Safety Interlocks 7.2 Variable-Frequency Drives in Refrigeration Plants 7.3 Power Factor, kW/HP, Overloads, and Machinery-Room Electrical Classification
8 Pressure-Enthalpy Diagrams and Properties
8.1 Reading the Ammonia P-h Diagram 8.2 Saturated Properties, psia vs psig, and Saturation Temperature 8.3 Superheat, Subcooling, and Flash Gas
9 Capacity, COP, and Efficiency
9.1 Enthalpy, Latent Heat, and Net Refrigerating Effect 9.2 COP, Tons of Refrigeration, and Heat Rejection Ratio 9.3 BHP/ton, Isentropic Efficiency, and Theoretical Discharge Temperature
10 Heat Transfer and Rejection
10.1 Q = UAΔT, LMTD, and Heat Exchangers 10.2 Condensers, Approach, and Wet-Bulb Limits 10.3 Specific Volume, Mass Flow, and Compression Ratio
11 System Screens and Performance KPIs
11.1 Using CIRO Operating Screens (normal vs abnormal) 11.2 kW/ton, BHP/ton, and KPI Dashboards 11.3 Power Cost, Demand Charges, and the Cost of Poor Operation
12 Approach, TD, and Oil-Cooling Diagnostics
12.1 Condenser Approach and Non-Condensables 12.2 Evaporator TD and Superheat Diagnostics 12.3 Thermosiphon Oil Coolers and Oil-Temperature Trends
13 Floating Head, Sequencing, and Slide Valves
13.1 Floating Head Pressure 13.2 Compressor Sequencing 13.3 Screw Slide-Valve Unloading and Feedback
14 Expansion Devices and DX Feed
14.1 Solenoid and TXV Pairs, Equalizers, and Hunting 14.2 Electronic Expansion Valves 14.3 Hand Expansion Valves and DX Coil Distribution
15 Pressure-Regulating and Pilot-Operated Valves
15.1 Back-Pressure Regulators 15.2 Crankcase Pressure Regulators and Gas-Pumped CPR Systems 15.3 Pilot-Operated Valves and High-to-Low Relief Regulators
16 Floats, Checks, Solenoid Failures, and Piping
16.1 High-Side Floats and High-Pressure Receivers 16.2 Check Valves, Discharge Checks, and Defrost Check Valves 16.3 Solenoid Failure Modes, Strainers, King Valves, and Ammonia Piping
17 Flooded and Liquid-Overfeed Basics
17.1 Flooded vs DX Advantages and Charge 17.2 Overfeed Ratios and Recirculation Rate 17.3 Surge Drums, Separators, and Wet Suction Returns
18 Pumps, Oil Management, and Level Control
18.1 Mechanical Liquid Pumps and NPSH 18.2 Oil Drain Pots, Rectifiers, and Thermosiphon Oil Management 18.3 Level Glasses, Float Switches, and High/Low Cutouts 18.4 Liquid-Line Sizing and High-/Low-Pressure Receivers
19 Two-Stage Compression and Intercoolers
19.1 Why Two-Stage: Compression Ratio and Discharge Temperature 19.2 Interstage Pressure Selection (Geometric Mean) 19.3 Open Flash Intercoolers 19.4 Closed Intercoolers and Two-Stage Troubleshooting
20 Cascade and Secondary Coolant Systems
20.1 NH3/CO2 Cascade Designs 20.2 Glycol and Brine Secondary Coolants (pH, freeze point, inhibitors) 20.3 Why Secondary Coolants and Glycol Testing/Maintenance
21 Evaporator Defrost
21.1 Hot-Gas Defrost Sequence 21.2 Defrost Drain Pressure-Relief Regulators and Soft Equalization 21.3 Time/Temperature Termination, Drain Pans, Water and Electric Defrost
14.3 Hand Expansion Valves and DX Coil Distribution
Key Takeaways Explain This Topic AI
A hand expansion valve is a manual needle: it sets feed rate to flooded coils, overfeed surge drums, and some DX; it does not hold superheat by itself.
CIRO-style two-stage plant diagrams show hand expansion from high-side or interstage liquid into evaporators or drums — metering, not a king-valve substitute.
DX distributors use nozzles or orifices to split two-phase feed among circuits; even split is the design intent.
Uneven circuit distribution floods some circuits and starves others in the same coil; mixed-outlet superheat can look acceptable while the compressor still sees slugs.
Last updated: September 2026
14.3 Hand Expansion Valves and DX Coil Distribution
A hand expansion valve (HEV) is a manual needle valve . An operator or a commissioning tech sets a stem position. There is no bulb, no stepper, and no superheat spring. Mass flow follows the opening, the liquid pressure, and the downstream pressure. CIRO tests HEVs because they are all over flooded and overfeed P&IDs, and because two-stage study-guide diagrams show them on evaporator feed . Supervisors who only think "TXV" miss half of Area 5 and most of the overfeed drawings.
Where an HEV belongs
Flooded evaporators and overfeed surge drums. Makeup liquid from the high-pressure receiver — or from an intercooler on a two-stage plant — is throttled through an HEV into a surge drum / low-pressure receiver or a flooded shell. A float , level transmitter, or the recirculation pump manages inventory . The HEV sets a feed rate . The glass or the level loop keeps the drum from pumping dry or filling the compressor. You are not chasing 10°F leaving superheat on a flooded coil. Leaving vapor from a properly separated flooded or overfeed vessel is essentially saturated . Superheat control is a DX idea.
Some DX. Small ammonia DX coils and older layouts may use an HEV instead of a TXV. Superheat then becomes an operator job : too far open floods; too far closed starves. That is acceptable only when the load is steady and someone is actually watching. "Crack the HEV and walk away" is not automatic superheat control.
Two-stage plants, CIRO Figure 3 style. The official study-guide two-stage schematic family shows hand expansion feeding evaporators (or the low-stage drums) from high-side or interstage liquid. Do not copy that copyrighted figure. Remember the idea : high-pressure liquid does not dump uncontrolled into a low-temperature evaporator. An HEV — or an automatic expansion device — drops pressure and meters mass. Booster suction, intercooler, and high-stage machines are drawn around that feed. If a stem shows an HEV on the evaporator liquid line of a two-stage plant, it is feed control .
Vocabulary trap: a king valve isolates the receiver. An HEV meters . An HEV is not a lockout. Needle valves are for throttling . Isolation for lockout is a stop valve that can be tagged.
Setting an HEV like a supervisor
Establish a stable high-side pressure and a known level in the source vessel (receiver or intercooler).
Open the HEV slowly while watching surge-drum level (flooded / overfeed) or suction superheat and frost line (DX).
On overfeed, the HEV is often makeup to the drum. The recirculation pump and overfeed ratio (commonly taught 3:1 to 4:1 mass circulated to mass evaporated) wet the coils. Do not confuse makeup metering with the pump loop.
Note or lock the stem. Vibration walks a needle overnight.
If drum level is climbing with the HEV barely cracked, look at other liquid sources: hot-gas defrost drain, transfer from another vessel, or a leaking automatic valve in parallel. If the drum is falling with the HEV several turns out, look at undersized liquid lines, flash gas, a plugged strainer, or a load the makeup cannot match.
DX coil distribution — nozzles and orifices
A DX evaporator is a bundle of parallel circuits . The TXV, EEV, or (rarely) HEV dumps a two-phase mixture into a distributor . Each circuit has a nozzle or orifice sized so mass flow splits evenly when the distributor sees the pressure drop it was designed for. After the circuits, a suction header mixes the leaving vapor. The TXV bulb or EEV sensors see that mixed stream — not each circuit.
Even split: every circuit finishes boiling near the same superheat, frost is uniform from inlet to a consistent dry-out, capacity matches the rating, oil returns with the vapor.
Uneven split is the exam diagnosis:
Starved circuits: little or no frost, high local superheat, unused surface, missing capacity.
Flooded circuits: wet tubes, frost or liquid into the header, low or zero superheat on those circuits, compressor flood risk.
The cruel point: some circuits flood while others starve in the same coil. The mixed-outlet superheat can look "about 10°F" while the compressor eats slugs from the wet circuits and the dry circuits contribute almost no tons. A single bulb or transducer averages . Frost pattern and circuit-by-circuit surface temperature beat that average.
Causes of a bad split:
Plugged distributor nozzles. One orifice closed starves that circuit; the others may overfeed because the valve is still trying to satisfy mixed superheat.
Missing or wrong-size orifice after a rebuild or a "we had extras" parts swap. Orifice kits are matched to refrigerant, capacity, and circuit count.
Distributor too small or too large for the valve's mass flow, so the intended pressure drop never appears.
Oil-logged circuits that stop boiling.
Uneven air loading — blocked return, product stacked against one face — so some circuits have no load and overfeed while loaded circuits starve.
Feed header not level ; gravity bias on a horizontal coil.
After a coil rebuild, count nozzles back in . Cleaning the liquid strainer without accounting for distributor orifices leaves a mystery starve that no TXV spring turn will fix.
Device map (keep these jobs separate)
- Device What it controls Typical ammonia service
- Hand expansion valve Manual mass-feed opening Flooded / overfeed makeup; some DX; two-stage evaporator feed
- TXV Superheat via bulb and equalizer DX coils
- EEV Superheat via temperature and pressure DX coils, wide or low load
- Liquid solenoid On/off, pump-down, defrost isolation Upstream of TXV or EEV
- Distributor nozzles / orifices Split among DX circuits DX evaporators
- King valve Receiver isolation Not metering
- Exam traps
An HEV on a surge drum is not a TXV. Do not look for DX leaving superheat on a flooded coil.
A two-stage diagram with HEVs to evaporators is still expansion . The intercooler is a different vessel with its own level and feed.
Replacing a distributor without matching orifice kits recreates uneven feed on the next pull-down.
Uneven frost is not automatically "low charge." Charge, strainer, solenoid, TXV, and nozzles can all starve selected circuits. Walk the coil face.
Overfeed coils also need even feed among parallel circuits, but they are intentionally wet . The DX problem is that the leaving vapor is supposed to be superheated and evenly finished. Mixing those two pictures is how people overfeed a DX coil "to make frost look better" and then slug the machine.
When a CIRO stem gives you a two-stage plant with an HEV on the evaporator and a DX freezer with a distributor on another circuit, name the devices by job : manual feed versus superheat control versus circuit split. That vocabulary is the section.