Study guide
17.1 Flooded vs DX Advantages and Charge
RETA CIRO Certified Industrial Refrigeration Operator Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Current Exam Facts 1.2 Test-Day Tools, On-Screen References, and Calculators 1.3 CIRO vs CARO and the RETA Credential Path
2 IIAR and ASHRAE Standards
2.1 IIAR 2 and ASHRAE 15 Machinery-Room Design 2.2 IIAR 6 Inspection, Testing, and Maintenance 2.3 IIAR 7 Operating Procedures and IIAR 9 Existing Systems
3 OSHA Process Safety Management
3.1 PSM Applicability and the 14 Elements 3.2 Process Safety Information 3.3 Process Hazard Analysis 3.4 Operating Procedures, Training, Contractors, and PSSR
4 Integrity, Change, and Emergency Programs
4.1 Mechanical Integrity and Pressure-Relief Valves 4.2 Hot Work and Management of Change 4.3 Incident Investigation and Compliance Audits 4.4 Emergency Planning, EPA RMP, and the General Duty Clause
5 Ammonia Hazards and Machinery-Room Safety
5.1 Ammonia Properties, SDS, and Exposure Limits 5.2 Detection, Ventilation, and Emergency Shutdown 5.3 Eyewash, PPE, Materials Compatibility, and ASME B31.5 Piping
6 Three-Phase Motors and Starting
6.1 Three-Phase Motors, Nameplates, and FLA 6.2 Wye-Delta and Reduced-Voltage Starting 6.3 Voltage Unbalance 6.4 Single-Phasing, Rotation Checks, and Screw Compressors
7 Ladder Diagrams, VFDs, and Power
7.1 Ladder Diagrams, Seal-In Circuits, and Safety Interlocks 7.2 Variable-Frequency Drives in Refrigeration Plants 7.3 Power Factor, kW/HP, Overloads, and Machinery-Room Electrical Classification
8 Pressure-Enthalpy Diagrams and Properties
8.1 Reading the Ammonia P-h Diagram 8.2 Saturated Properties, psia vs psig, and Saturation Temperature 8.3 Superheat, Subcooling, and Flash Gas
9 Capacity, COP, and Efficiency
9.1 Enthalpy, Latent Heat, and Net Refrigerating Effect 9.2 COP, Tons of Refrigeration, and Heat Rejection Ratio 9.3 BHP/ton, Isentropic Efficiency, and Theoretical Discharge Temperature
10 Heat Transfer and Rejection
10.1 Q = UAΔT, LMTD, and Heat Exchangers 10.2 Condensers, Approach, and Wet-Bulb Limits 10.3 Specific Volume, Mass Flow, and Compression Ratio
11 System Screens and Performance KPIs
11.1 Using CIRO Operating Screens (normal vs abnormal) 11.2 kW/ton, BHP/ton, and KPI Dashboards 11.3 Power Cost, Demand Charges, and the Cost of Poor Operation
12 Approach, TD, and Oil-Cooling Diagnostics
12.1 Condenser Approach and Non-Condensables 12.2 Evaporator TD and Superheat Diagnostics 12.3 Thermosiphon Oil Coolers and Oil-Temperature Trends
13 Floating Head, Sequencing, and Slide Valves
13.1 Floating Head Pressure 13.2 Compressor Sequencing 13.3 Screw Slide-Valve Unloading and Feedback
14 Expansion Devices and DX Feed
14.1 Solenoid and TXV Pairs, Equalizers, and Hunting 14.2 Electronic Expansion Valves 14.3 Hand Expansion Valves and DX Coil Distribution
15 Pressure-Regulating and Pilot-Operated Valves
15.1 Back-Pressure Regulators 15.2 Crankcase Pressure Regulators and Gas-Pumped CPR Systems 15.3 Pilot-Operated Valves and High-to-Low Relief Regulators
16 Floats, Checks, Solenoid Failures, and Piping
16.1 High-Side Floats and High-Pressure Receivers 16.2 Check Valves, Discharge Checks, and Defrost Check Valves 16.3 Solenoid Failure Modes, Strainers, King Valves, and Ammonia Piping
17 Flooded and Liquid-Overfeed Basics
17.1 Flooded vs DX Advantages and Charge 17.2 Overfeed Ratios and Recirculation Rate 17.3 Surge Drums, Separators, and Wet Suction Returns
18 Pumps, Oil Management, and Level Control
18.1 Mechanical Liquid Pumps and NPSH 18.2 Oil Drain Pots, Rectifiers, and Thermosiphon Oil Management 18.3 Level Glasses, Float Switches, and High/Low Cutouts 18.4 Liquid-Line Sizing and High-/Low-Pressure Receivers
19 Two-Stage Compression and Intercoolers
19.1 Why Two-Stage: Compression Ratio and Discharge Temperature 19.2 Interstage Pressure Selection (Geometric Mean) 19.3 Open Flash Intercoolers 19.4 Closed Intercoolers and Two-Stage Troubleshooting
20 Cascade and Secondary Coolant Systems
20.1 NH3/CO2 Cascade Designs 20.2 Glycol and Brine Secondary Coolants (pH, freeze point, inhibitors) 20.3 Why Secondary Coolants and Glycol Testing/Maintenance
21 Evaporator Defrost
21.1 Hot-Gas Defrost Sequence 21.2 Defrost Drain Pressure-Relief Regulators and Soft Equalization 21.3 Time/Temperature Termination, Drain Pans, Water and Electric Defrost
17.1 Flooded vs DX Advantages and Charge
Key Takeaways Explain This Topic AI
A flooded evaporator keeps the heat-transfer surface filled with boiling liquid, so inside HTC stays high and coil-outlet superheat is near zero.
DX (dry expansion) meters liquid with a TXV or EEV so the coil leaves as superheated vapor; evaporator charge is lower and the dry-out zone has poor HTC.
Industrial anhydrous ammonia plants are mostly flooded vessels and liquid-overfeed coils; DX is the minority feed on large NH3 systems.
Flooded and overfeed evaporators hold more refrigerant mass because liquid density dwarfs vapor density — that inventory is a design choice and a PSM/RMP pounds issue.
Do not commission an overfeed coil to a DX superheat target; forcing outlet superheat starves a wet system.
Last updated: September 2026
17.1 Flooded vs DX Advantages and Charge
CIRO Liquid Overfeed and Flooded Systems is 20 scored items (15% of the sitting). Area 5 already tested DX solenoids, TXVs, and EEVs. Area 6 is why most of the ammonia plants you supervise do not run dry-expansion evaporators as the plant standard: they run flooded vessels or liquid-overfeed coils. You must contrast the two feed methods, name the heat-transfer and charge consequences, and explain why industrial anhydrous ammonia prefers a wet coil.
What flooded actually means
A flooded evaporator keeps the heat-transfer surface wetted with boiling liquid . The coil, plate pack, or shell is not trying to dry the refrigerant out before it leaves. Two-phase mixture — liquid plus vapor — is present over most of the circuit. Heat from the load (air, glycol, process fluid) goes into nucleate boiling and forced-convection boiling, not into superheating a dry vapor film on the last third of the tube.
That wetting is the point. Liquid refrigerant contacting metal has a much higher heat-transfer coefficient (HTC) than superheated vapor. A dry-out patch on the inside of a tube is almost an insulator compared with a boiling film. Flooded and overfeed designs keep those dry patches from forming, so the evaporator can hold a smaller temperature difference (TD) for the same capacity, or more capacity at the same TD.
Leaving the evaporator, flooded and overfeed circuits send a wet mixture toward a separator . Superheat at the coil outlet is near zero . The vapor that finally goes to the compressor is dried in the surge drum / low-pressure receiver, not inside the last few feet of coil. If you clip a thermometer on a wet suction header and subtract saturation temperature, you are not looking at a DX superheat that is supposed to be 8–12°F. You are looking at two-phase fluid that should be near saturation.
Three flooded architectures (same wetting idea)
Operators mix the words. The exam cares that all three keep the surface wet :
Flooded shell-and-tube (or plate) chiller. Refrigerant boils in the shell (or in a flooded plate pack). A level control keeps tubes submerged. Makeup liquid comes from a high-side float or a level valve. Vapor leaves the top to suction. This is flooded vessel operation.
Gravity-flooded / thermosiphon coil. A surge drum at the evaporator feeds liquid down; two-phase returns up by density difference. Elevation and pressure drop limit how far the coil can sit from the drum. No recirculation pump on that coil.
Liquid overfeed (liquid recirculation). A mechanical pump or gas pump forces extra liquid through remote coils. Leftover liquid returns in a wet suction to a plant LPR / recirculator . This is the warehouse penthouse workhorse. Section 17.2 owns the ratio; this section owns why you bother.
Overfeed is not a third refrigerant. It is flooded-coil operation with extra liquid mass so every circuit stays wet even when the evaporated portion is small.
What DX (dry expansion) does instead
Direct expansion (DX) — also called dry expansion — meters liquid so the refrigerant finishes evaporating inside the coil and leaves as superheated vapor . A thermostatic expansion valve (TXV) or electronic expansion valve (EEV) holds that superheat. There is no dedicated wet-return header dumping two-phase fluid into a plant recirculator for that coil. A liquid-line solenoid ahead of the valve is on/off for pump-down, isolation, and defrost (Chapter 14).
DX advantages CIRO still expects you to name:
Less refrigerant charge in the evaporator. The outlet end is mostly vapor. Inventory is a liquid film plus vapor fill, not a flooded tube.
Simpler piping on small systems: liquid in, superheated suction out, no recirculation pump, no wet suction main sized for two-phase flow.
Superheat is a compressor-protection signal. If the TXV/EEV is healthy, liquid should not leave the coil. An accumulator is a backup, not the primary separator of a recirculation plant.
DX penalties on large industrial ammonia:
The outlet end of the circuit is vapor . HTC collapses where quality approaches 1.0. You pay with higher TD , more coil surface, or both.
Distribution through a distributor and many circuits is harder with ammonia's high latent heat and small mass flow per ton . Some circuits starve while others flood.
A failed-open TXV or lost superheat slugs the compressor unless an accumulator is in the way. Flooded plants put a vessel and high-level cutout in that path on purpose.
Oil return on DX depends on leaving-vapor velocity. Ammonia and mineral oil do not mix well. Large plants usually manage oil at the separator and oil pots instead (Chapter 18).
Industrial ammonia is mostly flooded and liquid-overfeed, not DX. DX still appears on small process evaporators, some packaged units, and a few penthouse air units. Do not tell the exam that ammonia DX does not exist. Tell it that large industrial NH3 prefers wet coils .
Charge: why flooded holds more pounds
Charge is the mass of refrigerant sitting in the circuit. A flooded tube, shell-and-tube chiller, or overfeed coil kept full of boiling liquid holds far more ammonia than a DX coil of the same physical volume, because liquid density is orders of magnitude higher than vapor density .
That extra inventory is not wasted decoration. It is the buffer that keeps the surface wet when load spikes, when a circuit is slightly starved, or when a pump is ramping. It is also a PSM/RMP inventory issue. More pounds in evaporators and surge drums can matter at the 10,000 lb anhydrous ammonia threshold (OSHA 29 CFR 1910.119 Appendix A; EPA 40 CFR 68). Flooded/overfeed plants often have large low-pressure receivers . DX packaged systems often do not. The operator's job is not to minimize charge at all costs; it is to know where the pounds live and why the design put them there.
Worked contrast (order of magnitude, not a RETA constant): a small DX freezer coil might hold a few dozen pounds of ammonia in the tubes. The same room on liquid overfeed , with a wet return and a recirculator serving several penthouses, can hold hundreds to thousands of pounds in the LPR plus the coils and wet suction. CIRO will not ask you to invent a catalog charge. It will ask whether flooded/overfeed increases evaporator charge relative to DX. It does.
Heat transfer, TD, and leaving state
- Feature Flooded / liquid overfeed DX (dry expansion)
- Coil fill Boiling liquid over most of the surface Liquid → two-phase → superheated vapor
- Outlet state Wet mixture; near-zero superheat at the coil Superheated vapor; TXV/EEV holds SH
- Inside-tube HTC High (boiling liquid) High in two-phase, low in the dry-out zone
- Typical evaporator TD Lower for the same load Higher, or more surface required
- Feed device Level control, gravity, or recirculation pump / gas pump TXV or EEV plus liquid solenoid
- Charge in evaporator Higher Lower
- Compressor protection Separator + high-level cutout ; wet returns expected Superheat + optional accumulator
- Industrial NH3 use Dominant on large plants Limited / smaller evaporators
Evaporator TD is the difference between entering air (or fluid) temperature and refrigerant saturation temperature. Because flooded/overfeed keeps the inside wet, you can often run closer to the space, or the same refrigerant temperature with more capacity. On a CIRO screen, a flooded coil showing a high TD with a coil that is not fully frosted to the header is not proving that DX superheat is healthy — it is often underfeed, oil film, frost, or lost recirculation . A DX coil should show superheat at the bulb. A flooded coil should not be judged by DX superheat rules.
Control philosophy, not just hardware
Flooded vessels typically hold level . A high-side float, low-side float, or modulating level valve keeps the boiling surface covered. Liquid-overfeed coils typically do not try to hold a level in the coil. A pump (or gas-powered recirculator) overfeeds liquid; the coil stays wet; leftover liquid returns in the wet suction to the separator.
DX control is superheat . Overfeed control is wetted surface plus separator level . If you apply a DX diagnostic (chase 10°F superheat at a flooded coil outlet) you will starve a wet system or miss a real dry-out. If you apply a flooded diagnostic (expect wet returns) to a DX coil, you will accept liquid in the suction that the compressor cannot swallow.
A supervisor who throttles overfeed balancing valves until a suction header shows DX-like superheat has just converted a 4:1 coil into a starved DX coil without a TXV. Capacity falls. TD rises. That is a commissioning error, not a savings.
Why ammonia, specifically
Anhydrous ammonia has a large latent heat and a relatively small mass flow per ton . DX distributors designed around halocarbons do not automatically behave well with that small mass flow. Recirculating extra liquid multiplies the mass in the tubes so every circuit stays wetted even when the evaporated portion is small.
Ammonia's toxicity also argues for robust compressor protection: a surge drum / LPR with a high-level trip is a more forgiving last barrier than hoping a TXV never fails open on a 300 HP screw. Oil is another ammonia-specific reason. Mineral oil used with ammonia is immiscible and heavier. In a flooded vessel it tends to log in the bottom or in a drain pot, not ride out with the vapor the way it can in some miscible HFC DX circuits. Large plants concentrate oil management at the recirculator, oil pots, and rectifiers . Flooded/overfeed is the architecture that makes that oil strategy possible.
Exam traps
Flooded does not mean the whole plant is full. It means the evaporator surface is flooded with boiling liquid. High-side receivers and condensers have their own levels.
Overfeed is a type of flooded-coil operation , not a third mystery refrigerant. Liquid is pumped at a multiple of the evaporated mass so the coil stays flooded.
Low leaving superheat on a flooded coil is normal. Low leaving superheat on a DX coil is a flood-back warning.
More charge is a flooded/overfeed trait , not a defect, unless inventory was never accounted for in process safety information and RMP.
Do not claim a numeric HTC from memory if the stem does not give one. Claim the direction : boiling liquid is far better than dry vapor.