Study guide

12.3 Thermosiphon Oil Coolers and Oil-Temperature Trends

RETA CIRO Certified Industrial Refrigeration Operator Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Test-Day Tools, On-Screen References, and Calculators 1.3 CIRO vs CARO and the RETA Credential Path

2 IIAR and ASHRAE Standards

2.1 IIAR 2 and ASHRAE 15 Machinery-Room Design 2.2 IIAR 6 Inspection, Testing, and Maintenance 2.3 IIAR 7 Operating Procedures and IIAR 9 Existing Systems

3 OSHA Process Safety Management

3.1 PSM Applicability and the 14 Elements 3.2 Process Safety Information 3.3 Process Hazard Analysis 3.4 Operating Procedures, Training, Contractors, and PSSR

4 Integrity, Change, and Emergency Programs

4.1 Mechanical Integrity and Pressure-Relief Valves 4.2 Hot Work and Management of Change 4.3 Incident Investigation and Compliance Audits 4.4 Emergency Planning, EPA RMP, and the General Duty Clause

5 Ammonia Hazards and Machinery-Room Safety

5.1 Ammonia Properties, SDS, and Exposure Limits 5.2 Detection, Ventilation, and Emergency Shutdown 5.3 Eyewash, PPE, Materials Compatibility, and ASME B31.5 Piping

6 Three-Phase Motors and Starting

6.1 Three-Phase Motors, Nameplates, and FLA 6.2 Wye-Delta and Reduced-Voltage Starting 6.3 Voltage Unbalance 6.4 Single-Phasing, Rotation Checks, and Screw Compressors

7 Ladder Diagrams, VFDs, and Power

7.1 Ladder Diagrams, Seal-In Circuits, and Safety Interlocks 7.2 Variable-Frequency Drives in Refrigeration Plants 7.3 Power Factor, kW/HP, Overloads, and Machinery-Room Electrical Classification

8 Pressure-Enthalpy Diagrams and Properties

8.1 Reading the Ammonia P-h Diagram 8.2 Saturated Properties, psia vs psig, and Saturation Temperature 8.3 Superheat, Subcooling, and Flash Gas

9 Capacity, COP, and Efficiency

9.1 Enthalpy, Latent Heat, and Net Refrigerating Effect 9.2 COP, Tons of Refrigeration, and Heat Rejection Ratio 9.3 BHP/ton, Isentropic Efficiency, and Theoretical Discharge Temperature

10 Heat Transfer and Rejection

10.1 Q = UAΔT, LMTD, and Heat Exchangers 10.2 Condensers, Approach, and Wet-Bulb Limits 10.3 Specific Volume, Mass Flow, and Compression Ratio

11 System Screens and Performance KPIs

11.1 Using CIRO Operating Screens (normal vs abnormal) 11.2 kW/ton, BHP/ton, and KPI Dashboards 11.3 Power Cost, Demand Charges, and the Cost of Poor Operation

12 Approach, TD, and Oil-Cooling Diagnostics

12.1 Condenser Approach and Non-Condensables 12.2 Evaporator TD and Superheat Diagnostics 12.3 Thermosiphon Oil Coolers and Oil-Temperature Trends

13 Floating Head, Sequencing, and Slide Valves

13.1 Floating Head Pressure 13.2 Compressor Sequencing 13.3 Screw Slide-Valve Unloading and Feedback

14 Expansion Devices and DX Feed

14.1 Solenoid and TXV Pairs, Equalizers, and Hunting 14.2 Electronic Expansion Valves 14.3 Hand Expansion Valves and DX Coil Distribution

15 Pressure-Regulating and Pilot-Operated Valves

15.1 Back-Pressure Regulators 15.2 Crankcase Pressure Regulators and Gas-Pumped CPR Systems 15.3 Pilot-Operated Valves and High-to-Low Relief Regulators

16 Floats, Checks, Solenoid Failures, and Piping

16.1 High-Side Floats and High-Pressure Receivers 16.2 Check Valves, Discharge Checks, and Defrost Check Valves 16.3 Solenoid Failure Modes, Strainers, King Valves, and Ammonia Piping

17 Flooded and Liquid-Overfeed Basics

17.1 Flooded vs DX Advantages and Charge 17.2 Overfeed Ratios and Recirculation Rate 17.3 Surge Drums, Separators, and Wet Suction Returns

18 Pumps, Oil Management, and Level Control

18.1 Mechanical Liquid Pumps and NPSH 18.2 Oil Drain Pots, Rectifiers, and Thermosiphon Oil Management 18.3 Level Glasses, Float Switches, and High/Low Cutouts 18.4 Liquid-Line Sizing and High-/Low-Pressure Receivers

19 Two-Stage Compression and Intercoolers

19.1 Why Two-Stage: Compression Ratio and Discharge Temperature 19.2 Interstage Pressure Selection (Geometric Mean) 19.3 Open Flash Intercoolers 19.4 Closed Intercoolers and Two-Stage Troubleshooting

20 Cascade and Secondary Coolant Systems

20.1 NH3/CO2 Cascade Designs 20.2 Glycol and Brine Secondary Coolants (pH, freeze point, inhibitors) 20.3 Why Secondary Coolants and Glycol Testing/Maintenance

21 Evaporator Defrost

21.1 Hot-Gas Defrost Sequence 21.2 Defrost Drain Pressure-Relief Regulators and Soft Equalization 21.3 Time/Temperature Termination, Drain Pans, Water and Electric Defrost

12.3 Thermosiphon Oil Coolers and Oil-Temperature Trends

Key Takeaways Explain This Topic AI

A thermosiphon oil cooler uses high-side liquid ammonia and gravity/density difference — no refrigerant pump — to take heat out of screw oil.

Oil inlet runs near discharge temperature; oil outlet must be cooler. A sample-screen 136°F oil-out is a healthy class; 154°F is an abnormal high-oil flag.

Refrigerant leaving the oil cooler should be liquid or two-phase as designed; a superheated refrigerant outlet means the thermosiphon is starved or blocked.

High oil temperature at 100% slide valve with high discharge points to hot cooling water or condenser sump, a fouled cooler, or overcompression — not to 'full load is supposed to look like 154°F.'

A shared thermosiphon header can starve running coolers when an offline unit fills with liquid.

Last updated: September 2026

12.3 Thermosiphon Oil Coolers and Oil-Temperature Trends

Industrial ammonia screws dump a large fraction of input power into oil . Oil seals the rotors, lubricates bearings, and leaves the machine near discharge temperature . That heat has to leave the oil before the oil goes back in. CIRO screens show oil in, oil out, and often a refrigerant temperature on the cooler. Those three numbers diagnose the cooler faster than waiting for a bearing-metal alarm.

What a thermosiphon oil cooler is

A thermosiphon (also spelled thermosyphon) oil cooler is a heat exchanger — often a plate pack or shell-and-tube — that cools compressor oil with high-side liquid ammonia . There is no refrigerant pump . Liquid from the condenser or high-pressure receiver flows down a liquid leg into the cooler (the cooler sits below the liquid source). Oil heat boils some of that liquid. The lower-density two-phase mixture rises back to the condenser or receiver vapor space. Gravity and density difference keep the loop moving.

Contrast with liquid injection (refrigerant dumped into the compressor, which raises mass flow and can cost kW/ton) and water or glycol oil coolers (depend on tower or process water). A typical CIRO plant description is thermosiphon oil cooling plus an evaporative condenser : the oil cooler is riding the same high-side liquid the condenser just made. If Chapter 12.1 left you with a dirty or air-bound condenser, this chapter is where that heat shows up as hot oil .

Temperatures you should see

Oil inlet (from the separator / discharge end) sits near discharge temperature — often in a 160–185°F neighborhood at load, depending on ratio and injection design. It is supposed to be the hot number.

Oil outlet (back to the compressor) is cooler . A healthy screen example is 136°F . That is a normal oil-out class for many loaded screws on thermosiphon.

154°F oil on the same style of screen is abnormal . An 18°F hike is not a thermocouple shrug. Treat 154°F as a high-oil-temperature flag, especially at 100% slide valve .

Refrigerant leaving the oil cooler should be liquid or two-phase , as the manufacturer piped it. A thermosiphon that is fed and circulating does not superheat the ammonia on the way out; there is still liquid present to boil. If the refrigerant outlet is superheated , the loop boiled dry and then the vapor kept taking heat. That is a starved or blocked thermosiphon , not extra-good cooling.

Starved or blocked loop — refrigerant outlet superheated

Walk the loop before you blame the compressor:

  • Liquid feed valve throttled or closed
  • Strainer or nozzle plugged (construction debris, rust, oil)
  • Receiver level too low — no static head to push liquid into the cooler
  • Equalizer, vent, or return riser blocked or vapor-bound

Shared thermosiphon header : when one compressor cycles off , its cooler can fill with liquid and starve the running machines on the same header

Cooler elevation or reversed riser after a rebuild

Oil may still look tolerable for a few minutes while remaining liquid boils off; then oil-out climbs and the refrigerant outlet goes superheated . That pairing — hot oil plus superheated refrigerant out — is almost never high wet-bulb only. Fix feed and circulation.

If refrigerant out is still two-phase and oil is hot, the limitation is oil-side fouling , too much heat (ratio and load), or a hot condensing reference (the liquid you are boiling against is itself too warm).

High oil temperature at 100% slide with high discharge

Full slide ( 100% ) is maximum swept volume and usually maximum oil-heat load . High discharge pressure and temperature means high heat of compression dumped into oil and discharge gas. The exam pairing is deliberate: this is when a weak cooler shows.

Three supervisor causes, in the order you can actually check:

Cooling water or condenser sump high. Thermosiphon liquid is only as cold as the high side that produced it. A hot evaporative-condenser sump , a high wet-bulb, or a water-cooled condenser running hot raises the boiling temperature in the oil cooler. Less ΔT, hotter oil. Non-condensables and dirty condensers therefore heat the oil even though the cooler is ammonia-cooled.

Fouled oil cooler. Oil-side varnish and coke, or refrigerant-side film, cut UA. Oil-in stays high; oil-out does not drop the design 30–50°F. Approach on the cooler itself (oil-out minus refrigerant sat T) opens up.

Overcompression. High compression ratio — low suction , high discharge , or both — raises discharge temperature and oil temperature even with a clean cooler. Fix the ratio (unloading, another stage, head pressure, suction problems) rather than opening an oil-cooler bypass as the first move.

136°F versus 154°F on a trend at the same slide and similar wet-bulb is a maintenance ticket , not a new normal. If 154°F appears only at 100% on the hottest afternoon, still check those three causes; do not live with it because the slide is loaded. Bearings see the oil that is actually injected, not the nameplate.

Do not copy a memorized good oil temperature from another plant as if RETA published a single legal value. Use the pattern : oil must leave cooler than it entered , refrigerant must not go superheated , and a step change from 136°F to 154°F at high load is a diagnostic. CIRO on-screen references include operating screens; you are being tested on whether 136°F and 154°F mean normal versus abnormal in that loaded, thermosiphon-cooled context.

Reading the oil row on a CIRO-style screen

A useful mental checklist:

Slide-valve position and whether discharge is high for today's wet-bulb.

Oil-in near discharge? If oil-in is cool , you may have injection or measurement issues, not a hero cooler.

Oil-out 136°F class versus 154°F class .

Refrigerant out: two-phase or liquid versus superheated .

Condenser liquid T versus condensing P (non-condensables heat the whole high side).

Thermosiphon oil cooling belongs in Monitoring System Performance because oil temperature is a leading indicator: it moves before a bearing alarm, and it explains kW/ton when head pressure and slide look acceptable but the machine is pumping heat into a dead cooler. Tie it to approach and TD: a plant that ignores 154°F oil while chasing only room temperature will pay in power and in the next teardown.

Loading diagram... Thermosiphon oil-cooler loop and starved-outlet check

Screw oil temperatures on a thermosiphon-cooled screen (°F)