Study guide
3.1 PSM Applicability and the 14 Elements
RETA CIRO Certified Industrial Refrigeration Operator Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Current Exam Facts 1.2 Test-Day Tools, On-Screen References, and Calculators 1.3 CIRO vs CARO and the RETA Credential Path
2 IIAR and ASHRAE Standards
2.1 IIAR 2 and ASHRAE 15 Machinery-Room Design 2.2 IIAR 6 Inspection, Testing, and Maintenance 2.3 IIAR 7 Operating Procedures and IIAR 9 Existing Systems
3 OSHA Process Safety Management
3.1 PSM Applicability and the 14 Elements 3.2 Process Safety Information 3.3 Process Hazard Analysis 3.4 Operating Procedures, Training, Contractors, and PSSR
4 Integrity, Change, and Emergency Programs
4.1 Mechanical Integrity and Pressure-Relief Valves 4.2 Hot Work and Management of Change 4.3 Incident Investigation and Compliance Audits 4.4 Emergency Planning, EPA RMP, and the General Duty Clause
5 Ammonia Hazards and Machinery-Room Safety
5.1 Ammonia Properties, SDS, and Exposure Limits 5.2 Detection, Ventilation, and Emergency Shutdown 5.3 Eyewash, PPE, Materials Compatibility, and ASME B31.5 Piping
6 Three-Phase Motors and Starting
6.1 Three-Phase Motors, Nameplates, and FLA 6.2 Wye-Delta and Reduced-Voltage Starting 6.3 Voltage Unbalance 6.4 Single-Phasing, Rotation Checks, and Screw Compressors
7 Ladder Diagrams, VFDs, and Power
7.1 Ladder Diagrams, Seal-In Circuits, and Safety Interlocks 7.2 Variable-Frequency Drives in Refrigeration Plants 7.3 Power Factor, kW/HP, Overloads, and Machinery-Room Electrical Classification
8 Pressure-Enthalpy Diagrams and Properties
8.1 Reading the Ammonia P-h Diagram 8.2 Saturated Properties, psia vs psig, and Saturation Temperature 8.3 Superheat, Subcooling, and Flash Gas
9 Capacity, COP, and Efficiency
9.1 Enthalpy, Latent Heat, and Net Refrigerating Effect 9.2 COP, Tons of Refrigeration, and Heat Rejection Ratio 9.3 BHP/ton, Isentropic Efficiency, and Theoretical Discharge Temperature
10 Heat Transfer and Rejection
10.1 Q = UAΔT, LMTD, and Heat Exchangers 10.2 Condensers, Approach, and Wet-Bulb Limits 10.3 Specific Volume, Mass Flow, and Compression Ratio
11 System Screens and Performance KPIs
11.1 Using CIRO Operating Screens (normal vs abnormal) 11.2 kW/ton, BHP/ton, and KPI Dashboards 11.3 Power Cost, Demand Charges, and the Cost of Poor Operation
12 Approach, TD, and Oil-Cooling Diagnostics
12.1 Condenser Approach and Non-Condensables 12.2 Evaporator TD and Superheat Diagnostics 12.3 Thermosiphon Oil Coolers and Oil-Temperature Trends
13 Floating Head, Sequencing, and Slide Valves
13.1 Floating Head Pressure 13.2 Compressor Sequencing 13.3 Screw Slide-Valve Unloading and Feedback
14 Expansion Devices and DX Feed
14.1 Solenoid and TXV Pairs, Equalizers, and Hunting 14.2 Electronic Expansion Valves 14.3 Hand Expansion Valves and DX Coil Distribution
15 Pressure-Regulating and Pilot-Operated Valves
15.1 Back-Pressure Regulators 15.2 Crankcase Pressure Regulators and Gas-Pumped CPR Systems 15.3 Pilot-Operated Valves and High-to-Low Relief Regulators
16 Floats, Checks, Solenoid Failures, and Piping
16.1 High-Side Floats and High-Pressure Receivers 16.2 Check Valves, Discharge Checks, and Defrost Check Valves 16.3 Solenoid Failure Modes, Strainers, King Valves, and Ammonia Piping
17 Flooded and Liquid-Overfeed Basics
17.1 Flooded vs DX Advantages and Charge 17.2 Overfeed Ratios and Recirculation Rate 17.3 Surge Drums, Separators, and Wet Suction Returns
18 Pumps, Oil Management, and Level Control
18.1 Mechanical Liquid Pumps and NPSH 18.2 Oil Drain Pots, Rectifiers, and Thermosiphon Oil Management 18.3 Level Glasses, Float Switches, and High/Low Cutouts 18.4 Liquid-Line Sizing and High-/Low-Pressure Receivers
19 Two-Stage Compression and Intercoolers
19.1 Why Two-Stage: Compression Ratio and Discharge Temperature 19.2 Interstage Pressure Selection (Geometric Mean) 19.3 Open Flash Intercoolers 19.4 Closed Intercoolers and Two-Stage Troubleshooting
20 Cascade and Secondary Coolant Systems
20.1 NH3/CO2 Cascade Designs 20.2 Glycol and Brine Secondary Coolants (pH, freeze point, inhibitors) 20.3 Why Secondary Coolants and Glycol Testing/Maintenance
21 Evaporator Defrost
21.1 Hot-Gas Defrost Sequence 21.2 Defrost Drain Pressure-Relief Regulators and Soft Equalization 21.3 Time/Temperature Termination, Drain Pans, Water and Electric Defrost
3.1 PSM Applicability and the 14 Elements
Key Takeaways Explain This Topic AI
OSHA 29 CFR 1910.119 Process Safety Management of Highly Hazardous Chemicals covers a process when anhydrous ammonia (CAS 7664-41-7) is at or above the Appendix A threshold quantity of 10,000 pounds
Ammonia solutions greater than 44% ammonia by weight have a separate Appendix A threshold of 15,000 pounds; industrial anhydrous plants almost always trip on the 10,000-pound anhydrous listing
Interconnected vessels, and nearby vessels that could share a potential release, count as one process — you do not get a free pass by splitting charge across packages that can dump into each other
PSM has 14 elements; this chapter owns applicability, employee participation, PSI, PHA, operating procedures, training, contractors, PSSR, and trade secrets, with one-line pointers to mechanical integrity, hot work, MOC, incidents, emergency/RMP, and audits
OSHA's ammonia refrigeration overview treats ammonia as corrosive, cites an odor threshold of 20 ppm, lists IDLH at 300 ppm, and gives a flammable range of about 15–28% by volume in air
Last updated: September 2026
Industrial ammonia refrigeration is not “just HVAC with a stronger smell.” Once a plant’s process holds enough anhydrous ammonia, OSHA treats it as a highly hazardous chemical process under 29 CFR 1910.119 , Process Safety Management of Highly Hazardous Chemicals (PSM). CIRO candidates are expected to know when the rule attaches , what a process is, and how the 14 elements divide the work of keeping a release from becoming a catastrophe. This section is the map. The next three sections teach the elements you operate: process safety information, process hazard analysis, and the cluster of operating procedures, training, contractors, and pre-startup safety review (PSSR).
The legal hook
PSM is a performance standard. OSHA does not hand you a fill-in-the-blank ammonia SOP. It requires a written program that identifies hazards, keeps information accurate, analyzes what can go wrong, and controls the people, procedures, and hardware that prevent a catastrophic release of toxic, reactive, or flammable chemicals. For ammonia plants, the usual coverage path is 1910.119(a)(1)(i) : a process that involves a chemical at or above the threshold quantity (TQ) listed in Appendix A .
Appendix A is a table of chemicals, CAS numbers, and TQs in pounds. The row that matters on almost every CIRO plant is:
- Chemical (Appendix A wording) CAS Threshold quantity
- Ammonia, Anhydrous 7664-41-7 10,000 pounds
- Ammonia solutions (>44% ammonia by weight) 7664-41-7 15,000 pounds
Anhydrous means the refrigerant in the vessels, piping, and packages — the inventory you would report as system charge, not the dilute janitorial ammonia in a spray bottle. Ammonia solutions greater than 44% by weight have a higher TQ of 15,000 lb . Mention that row so you do not confuse it with the anhydrous number; a typical industrial engine-room plant is anhydrous and trips on 10,000 lb , not 15,000 lb.
EPA’s Risk Management Program (40 CFR 68) also lists anhydrous ammonia at 10,000 lb . RMP is a sister program with a different agency and a community-offsite focus. You will treat emergency planning, RMP, and the General Duty Clause in a later chapter. For applicability on the CIRO exam, memorize OSHA Appendix A: 10,000 lb anhydrous .
What OSHA means by a “process”
Coverage is not “the north engine room” versus “the south penthouse” if those packages can share a release. OSHA defines a process as any activity involving a highly hazardous chemical, including use, storage, manufacturing, handling, or on-site movement — or a combination of those. Critically, any group of vessels that are interconnected , and separate vessels located so that a highly hazardous chemical could be involved in a potential release , are a single process .
That definition is how plants try — and fail — to stay under 10,000 lb by arguing that two machines are “separate systems.” If a high-side equalizer, a common pump-out station, a shared high-pressure receiver, or a piping arrangement could put both charges into one release, OSHA will add the inventories. Maximum intended inventory for the process (a PSI fact you will compile in the next section) is the number you compare to the TQ, not a hopeful nameplate on one compressor package.
PSM does not apply to retail facilities, oil or gas well drilling or servicing, or normally unoccupied remote facilities. Hydrocarbon-fuel and atmospheric-tank exceptions exist in the flammable-liquid paragraph of 1910.119(a). Those exceptions are not the CIRO ammonia path. Pressurized anhydrous ammonia refrigeration is an Appendix A chemical at 10,000 lb .
A small specialty plant that truly keeps maximum intended inventory under 10,000 lb anhydrous is not Appendix A-covered for ammonia. Most industrial cold storage, protein processing, and large refrigerated-distribution plants that a CIRO supervises are covered. If you are not sure, you count charge — you do not guess from square footage.
Why ammonia is on Appendix A
OSHA’s ammonia refrigeration overview is the snapshot operators should be able to recite without opening an SDS (the full SDS and exposure chapter comes later):
Ammonia is corrosive to tissue — eyes, skin, and respiratory tract.
OSHA cites an odor threshold of 20 ppm on that overview page. Odor is a warning, not a calibrated detector and not a substitute for ventilation or PPE.
IDLH is 300 ppm (immediately dangerous to life or health).
Ammonia is flammable in a range of about 15–28% by volume in air . It is harder to ignite than many hydrocarbons, but a machinery-room release can still reach a flammable mixture, which is why electrical classification, hot work, and emergency ventilation matter.
OSHA Table Z-1 lists an ammonia PEL of 50 ppm as an 8-hour TWA. That PEL belongs in process safety information as a required chemical fact. NIOSH REL and ACGIH TLV values (commonly 25 ppm TWA / 35 ppm STEL) are tighter recommended limits — label the authority when you quote them. They do not replace the OSHA PEL inside PSM’s chemical-information list.
The 14 elements — learn every name
PSM is one program with 14 elements (1910.119(c) through (p)). A CIRO is expected to name all 14 . This chapter goes deep on the operator-facing cluster listed below. Mechanical integrity, hot work, management of change, incident investigation, emergency planning and response (and RMP), and compliance audits are later chapters — one-line pointers only, so you know they exist and where they live.
Element (1910.119) Ammonia-plant example Depth in this guide
(c) Employee participation Written plan; operators sit on the engine-room PHA; employees get access to PHA and other PSM information This section
- (d) Process safety information SDS/PEL data, P&IDs, relief design basis, materials of construction Section 3.2
- (e) Process hazard analysis HAZOP of hot-gas defrost and king-valve isolation Section 3.3
- (f) Operating procedures Written steps for initial startup, emergency shutdown, pump-out Section 3.4
- (g) Training Initial operator training plus at least every-3-year refresher Section 3.4
- (h) Contractors Screw-compressor overhaul crew briefed on NH3 hazards and the EAP Section 3.4
- (i) Pre-startup safety review PSSR after a new vessel that changes PSI, before charging Section 3.4
- (j) Mechanical integrity ITM of vessels, piping, relief valves, rotating equipment Chapter 4 (pointer only)
- (k) Hot work permit Welding on an isolated, pumped-out oil pot Chapter 4 (pointer only)
(l) Management of change Different valve trim, new setpoint band, or new piping — not replacement-in-kind Chapter 4 (pointer only)
(m) Incident investigation Near-miss release during oil draining Chapter 4 (pointer only)
(n) Emergency planning and response EAP, rescue, coordination with responders; RMP overlap Chapter 4 (pointer only)
(o) Compliance audits Independent check that the written PSM program is real Chapter 4 (pointer only)
(p) Trade secrets Confidentiality agreements allowed; information still must be available to people compiling PSI, PHAs, procedures, investigations, emergency plans, and audits This section
Employee participation — 1910.119(c)
Employee participation is not a suggestion box. The employer must develop a written plan of action for how participation will work. The employer must consult with employees and their representatives on the conduct and development of process hazard analyses and on development of the other PSM elements . Employees and representatives must have access to process hazard analyses and to all other information required to be developed under the standard .
On an ammonia plant that means a CIRO-level operator is not a spectator. If a HAZOP of the recirculator skid is happening, people who actually start pumps, reset level columns, and isolate king valves belong in the room. If the written plan only interviews the safety director, it is not the element OSHA wrote. Access also means you can see the PHA report and the PSI package for the process you operate — not a redacted pamphlet.
Trade secrets — 1910.119(p)
Ammonia refrigeration is not a secret chemical, but plants still have vendor packages, control logic, and customer-process details they consider proprietary. Trade secrets cannot be used as a wall against PSM. The employer must make all information necessary to comply available to the people compiling process safety information, developing PHAs, writing operating procedures, investigating incidents, planning emergencies, and conducting compliance audits — without regard to possible trade secret status . The employer may require those people to sign confidentiality agreements . For CIRO purposes: you still get the P&ID and the relief basis; the company can still ask you not to photocopy the package for a competitor.
How a CIRO uses this on the floor
When a vendor says “we are not PSM because each skid is only 8,000 pounds,” you ask whether the skids are one process . When corporate says operators do not need the PHA because it is “engineering,” you point at employee participation and access . When a project wants to charge a new high-pressure receiver on Friday night, you ask whether PSSR is done because the modification changed PSI. Those are supervisor questions. The 14-element list is the checklist behind them.
Keep the later elements in view so you do not pretend PSM ends at procedures. Mechanical integrity is how hardware stays inside the design assumed by PSI. Hot work is a permit system for ignition sources. Management of change is how you stop “small” piping and setpoint changes from bypassing the PHA. Incident investigation , emergency planning (and EPA RMP), and compliance audits close the loop. They have their own chapter. You still must be able to name all 14 on the CIRO exam.