Study guide
2.3 Spirometer Troubleshooting
NBRC Registered Pulmonary Function Technologist RPFT
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Current Exam Facts 1.2 Content Outline Domains & Study Plan
2 Spirometry Instrumentation
2.1 Spirometer Types, Setup & Maintenance 2.2 Spirometer Calibration & Linearity 2.3 Spirometer Troubleshooting
3 Blood Gas & Gas Analyzers
3.1 Blood Gas Analyzer Setup, Maintain, Calibrate 3.2 Gas Analyzers & Water/Gas Absorbers 3.3 ABG & Gas Analyzer Troubleshooting and QC
4 Body Box, Exercise & Monitoring Equipment
4.1 Body Plethysmograph Setup & Calibration 4.2 Exercise, Field Walking & ECG Equipment 4.3 Pressure Devices, Valves & Gas Delivery Systems
5 Ancillary Equipment & Infection Control
5.1 Body Habitus, Sampling & Aerosol Equipment 5.2 Monitors & Emergency Management Equipment 5.3 Infection Control Materials & Methods
6 Quality Control Systems
6.1 Mechanical QC Devices 6.2 Biological Controls & Proficiency Testing 6.3 Laboratory Quality Management & SOPs
7 Patient Preparation & Safety
7.1 Body Habitus Measurements & Estimates 7.2 Patient Safety, Precautions & Adverse Events
8 Spirometry Procedures
8.1 Selecting Spirometry Protocols & Equipment 8.2 Performing Standard & Position-Variant Spirometry 8.3 Evaluating Spirometry Acceptability & Repeatability 8.4 Bronchodilator Response Studies
9 Static Lung Volumes
9.1 Gas Dilution Lung Volume Methods 9.2 Body Plethysmography Lung Volumes 9.3 Evaluating Lung Volume Validity
10 Diffusing Capacity (DLCO)
10.1 DLCO Protocol & Equipment Selection 10.2 Performing the DLCO Maneuver 10.3 Evaluating DLCO Validity
11 Blood Gas Sampling & Analysis Procedures
11.1 Arterial & Capillary Blood Sample Collection 11.2 Performing Blood Gas Analysis 11.3 CO-oximetry / Hemoximetry Procedures
12 Airway Responsiveness, Resistance & Muscle Strength
12.1 Bronchial Provocation Studies 12.2 Airways Resistance & Conductance by Plethysmography 12.3 Respiratory Muscle Strength (MIP/MEP/CPF)
13 Exercise, Oxygen, Home Testing & Education
13.1 Field Walking Tests (6MWT, Shuttle) 13.2 Monitored Exercise Testing 13.3 Oxygen Assessment & Titration 13.4 Home Testing Instruction & Patient Education
14 Calculations & Reference Ranges
14.1 Spirometry Calculations & Reference Equations 14.2 Lung Volume & DLCO Calculations/Corrections 14.3 Blood Gas & CO-oximetry Derived Calculations 14.4 Exercise, Oximetry & Special Test Calculations
15 Evaluating Result Reliability
15.1 Spirometry & Lung Volume Reliability 15.2 DLCO & Exercise Test Reliability 15.3 ABG, Monitoring & QC Reliability
16 Clinical Implications & Reporting
16.1 Pattern Recognition: Obstruction, Restriction, Mixed, Severity 16.2 Clinical Implications: DLCO, ABG, Airway Response, Exercise & Lab Context
2.3 Spirometer Troubleshooting
Key Takeaways Explain This Topic AI
NBRC Domain I.B.3 expects systematic troubleshooting of spirometers: leaks, zero drift, moisture, blocked filters, and loose connections
Volume–time and flow–volume displays show distinct error signatures for leak, early termination, obstruction in the circuit, and zero offset
Condensation on pneumotachs and saturated filters commonly flatten PEF and pull FEV1/FVC down without a true change in lung function
Decision order: stop testing → inspect circuit → re-zero → re-calibrate/linearity → replace disposable or user-serviceable parts → remove from service/service call
Never report clinical interpretations from waveforms that fail instrument QC; document and switch to a backup system when calibration cannot be restored
Last updated: August 2026
Troubleshooting is Domain I.B.3 — a scored skill
I.B Troubleshoot is one of the larger equipment sub-areas on the PFT Examination. Task I.B.3 Troubleshoot spirometers assumes you already know types, setup, and calibration (2.1–2.2). Exam stems show a bad curve, a failed syringe check, or a sudden change in a known subject’s values and ask for the next best action .
Good troubleshooters do not randomly reboot. They match error signatures to likely hardware causes , then walk a decision tree : re-calibrate vs replace parts vs service.
- Common fault categories
- 1. Leaks
- Where leaks occur
- Mouthpiece–lip seal and missing/loose nose clip (patient interface)
- Filter not seated; cracked disposable sensor housing
- Tubing cracks, loose barb connections, open sample ports
- Volume systems: rolling-seal tears, bell water-seal failure, bellows pinholes
- Pneumotach: loose pressure-sense lines (acts like a pneumatic leak/shunt)
- What you see
- Calibration syringe under-recovers at all flows (volume loss to room)
- Patient FVC lower than expected with a slow “bleed” on volume–time after apparent end-expiration
- Inability to hold a plateau on SVC/IC maneuvers
- Flow–volume loop with irregular scalloping or failure to return cleanly to baseline volume
Actions: soapy-water or manufacturer leak test on volume devices; listen/feel for hiss; reseat filter; replace cracked parts; re-instruct seal and nose clip; re-calibrate after repair.
2. Zero drift
Causes: incomplete warm-up, temperature change mid-session, electronic instability, moisture shifting pneumotach baseline, blocked reference port.
- What you see
- Baseline flow not at zero before the maneuver
- Volume–time slowly ramps without patient effort
- Integrated FVC drifts upward or downward between efforts
- Calibration strokes start from a non-zero baseline and recover wrong volumes
Actions: allow warm-up; dry sensor; clear ports; perform software zero/offset procedure; repeat calibration. If zero will not hold, remove from service.
3. Moisture / condensation on pneumotachs
Exhaled gas is warm and fully saturated. On a cooler pneumotach screen, water condenses, raising resistance and destroying the pressure–flow relationship.
- What you see
- Progressive drop in PEF/FEV1 across successive efforts in a session
- Noisy, tremulous flow signal
- Linearity fails at mid/high flows with syringe after patient testing
- Calibration that passed dry in the morning fails after several patients
Actions: use validated filters; do not leave wet filters on the head; follow heated-pneumotach or drying procedures if equipped; clean/dry/replace flow head; re-zero and re-run multi-flow calibration before more patients.
4. Blocked or high-resistance filters
Filters load with secretions, saliva, or packing debris.
- What you see
- Flattened PEF, prolonged rise time, scooped effort that looks like poor patient blast but is mechanical
- Patient complains of hard-to-blow / hard-to-inhale through the circuit
- Syringe high-flow recovery falls while low-flow may still pass
Actions: replace filter; never attempt to “clear” a disposable filter by forced air from the syringe into the sensor in a way that drives moisture deeper—replace and re-verify.
- 5. Loose connections and reversed lines
- What you see
- Intermittent dropouts on flow–volume loops
- Near-zero flow with obvious patient effort
- Inverted or mirror-image loops if inspiratory/expiratory sensing is reversed on dual-path systems
- Large stroke-to-stroke calibration scatter
Actions: reseat every connection; confirm color-coded pressure lines on Fleisch/Lilly heads; strain-relief tubing so patient movement does not tug ports; re-calibrate.
Error patterns on volume–time and flow–volume displays
Use displays as diagnostic instruments, not only patient report cards.
Volume–time (V–t) signatures
- Pattern on V–t Suspect
- Slow upward creep of volume with no effort Zero drift or leak into the measuring system
- Abrupt volume loss after peak (downward step) Leak to atmosphere mid-maneuver or software reset
Rounded, delayed rise without sharp onset Circuit resistance (wet pneumotach, blocked filter) or poor blast—confirm with hardware check first if multiple patients affected
- Failure to plateau; continuous small rise Leak, incomplete exhalation, or drift
- Calibration stroke volume low with straight, clean delivery Leak, span error, wrong syringe stops
- Flow–volume (F–V) signatures
Pattern on F–V Suspect
Blunted peak, slow rise to PEF Turbine inertia, obstruction in filter/mouthpiece, coaching—but if syringe high-flow also low → hardware
- Tremulous/noisy PEF region Moisture, loose connection, electrical interference
- Loop fails to close; volume axis wanders Zero drift, leak
- Mirror or inverted loops Reversed sensor orientation/lines
- Sudden notch mid-expiration on every effort, every patient Fixed circuit defect (kink, partial occlusion)
- Only one patient shows cough notches Patient artifact, not instrument
Key exam discrimination: If one patient has poor peaks, coach effort. If every patient after 10:00 has lower PEF and the afternoon syringe fails high flow, think moisture/obstruction , not an epidemic of obstruction.
Decision tree: re-calibrate vs replace parts vs service
Work top-down. Stop clinical testing when instrument fault is plausible. 1. STOP — do not report questionable results
- 2. INSPECT — filter, mouthpiece, tubing, water level/seals, sensor moisture, cables
- 3. CORRECT obvious setup faults — reseat, replace disposables, dry/clean per IFU
- 4. ZERO — perform baseline zero after warm-up
- 5. CALIBRATE — 3-L syringe at multiple flows (section 2.2)
- ├─ PASS → resume testing; document intervention
- └─ FAIL → go to 6
- 6. ISOLATE QC device — try second certified syringe if available
- ├─ Second syringe PASS → remove bad syringe (I.A.17); spirometer OK
- └─ Second syringe FAIL → spirometer problem → go to 7
- 7. REPLACE user-serviceable parts — pneumotach head/screen, turbine assembly,
- rolling seal (if trained), O-rings, tubing set; then re-zero + re-calibrate
- ├─ PASS → return to service with full documentation
- └─ FAIL → go to 8
- 8. OUT OF SERVICE — tag device, notify supervisor/service, switch to backup
- Do NOT apply correction factors to patient data
- When re-calibration alone is appropriate
- After warm-up that was skipped
- After zeroing a stable, dry sensor
- After reconnecting a loose but undamaged tube
- After environmental entry correction (legitimate temperature/PB fix—not falsification)
- When replacing parts is appropriate
- Saturated/contaminated filter or disposable flow sensor
- Visibly dirty pneumotach screen or sticky turbine
- Cracked mouthpiece adapter, torn seal, split tubing
- Damaged syringe O-rings (replace syringe seals or the syringe itself)
- When service / remove from service is required
- Electronics will not zero or store calibration
- Linearity fails after clean sensor and verified syringe
- Persistent leak in volume chamber that user parts cannot fix
- Safety issues (frayed power cord, cracked body box interface if integrated, fluid intrusion into electronics)
- Recurrent failures after temporary “fixes”
- Integrated scenarios (RPFT style)
- Scenario A — Morning pass, midday fail
Morning multi-flow calibration 2.96–3.04 L. After 12 patients, PEF values look systematically low. Repeat calibration: slow 3.00 L, fast 2.86 L .
Best action: Suspect moisture/contamination ; replace filter and dry/clean pneumotach; re-zero; re-linearize. Do not interpret all midday patients as new obstruction without instrument recovery.
Scenario B — Leak on volume spirometer
Syringe recovers 2.70 L every stroke; soapy water bubbles at rolling seal.
Best action: Replace/repair seal (trained personnel) or remove from service; re-calibrate after repair. Re-calibrating alone without fixing the seal will fail again.
Scenario C — Zero drift
Volume–time creeps up 50 mL/s before the patient starts.
Best action: Abort maneuver; dry/warm sensor; re-zero ; verify calibration; then resume.
Scenario D — Bad syringe
All techs fail calibration until a loaner certified syringe passes.
Best action: Remove original syringe from QC inventory; document; continue testing on the spirometer.
Scenario E — Coaching vs hardware
Only one anxious patient has blunted PEF; syringe still 3.00 L at high flow.
Best action: Coaching and technique (Domain II)—not sensor replacement.
Documentation during troubleshooting
Record:
- Fault description and which patients/time window may be affected
- Waveform observations (attach screenshots if system allows)
- Steps tried (filter change, zero, calibration data)
- Final disposition (returned to service / out of service)
- Whether any results need to be voided and repeated
Quality systems and NBRC items both reward the technologist who protects data integrity over the one who “finishes the schedule” on a failed device.
Quick fault → first action table
- Finding First best action
- Syringe low all flows, hiss at connector Reseat/replace tubing; leak test; re-calibrate
- Baseline not zero Warm-up + zero; then calibrate
- High-flow syringe fail after many patients Replace wet filter; dry/clean pneumotach; multi-flow calibrate
- Inverted loop on all efforts Check sensor orientation / pressure lines
- Scatter on calibration, intermittent dropout Secure loose connections; retest
- Still failing after clean head + good syringe Tag out of service; call service
- Single patient poor PEF, hardware QC pass Coach effort / check mouthpiece seal
- Closing the Domain I spirometry loop
Sections 2.1–2.3 form a single exam storyline: choose and set up the right hardware → prove it with 3-L accuracy and linearity → recognize and fix failure modes without contaminating clinical data . Downstream Domain II chapters assume this foundation; Domain III reliability questions will again ask whether a pretty curve came from a trustworthy instrument.
Practice applying the decision tree on every vignette until “re-calibrate vs replace vs service” is automatic under the RPFT’s timed, high-cut standard.