Study guide
5.1 Secondary Port Calculations: Time & Height Differences
RYA Coastal Skipper / Yachtmaster Offshore Shorebased Theory Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: The Magnetic Compass, Variation & Deviation
1.1 The Magnetic Compass, Earth's Magnetic Field & Variation 1.2 Compass Deviation, Deviation Cards & Swinging the Compass 1.3 The Mercator Projection, Chart Symbols & Latitude Distance Scales
2 Chapter 2: Dead Reckoning, Estimated Position & Leeway
2.1 Dead Reckoning (DR) & Water Track Principles 2.2 Wind Leeway & Calculating Water Track 2.3 Plotting an Estimated Position (EP) with Tidal Stream
3 Chapter 3: Course to Steer, Vector Triangles & Position Lines
3.1 Course to Steer (CTS) Single-Hour Vector Triangles 3.2 Multi-Hour Courses to Steer & Changing Tidal Streams 3.3 Visual Position Lines, Three-Bearing Fixes & Cocked Hats 3.4 Running Fixes, Transferred Position Lines & Electronic Aids
4 Chapter 4: Tidal Heights, Datums & Standard Port Calculations
4.1 Tidal Theory, Astronomical Causes, Springs & Neaps 4.2 Chart Datums, Lowest Astronomical Tide (LAT) & Soundings 4.3 Standard Port Tidal Calculations & The Rule of Twelfths
5 Chapter 5: Secondary Ports, Tidal Streams & Dynamic Waters
5.1 Secondary Port Calculations: Time & Height Differences 5.2 Using Admiralty Tidal Curves for Height at Any Time 5.3 Tidal Diamonds, Stream Atlases & Tidal Gates 5.4 Tidal Overfalls, Races, Wind-Over-Tide & Shallow Water Effects
6 Chapter 6: IRPCS Steering & Sailing Rules
6.1 General Rules, Look-out, Safe Speed & Risk of Collision (Rules 1-8) 6.2 Narrow Channels & Traffic Separation Schemes (Rules 9 & 10) 6.3 Steering Rules: Sailing Vessels, Overtaking, Head-on & Crossing (Rules 12-17) 6.4 Responsibilities Between Vessels & Restricted Visibility (Rules 18 & 19)
7 Chapter 7: IRPCS Navigation Lights, Day Shapes & Sound Signals
7.1 Fundamentals of Navigation Lights & Day Shapes (Rules 20-22) 7.2 Specific Vessel Lights & Shapes: Power, Sail, Towing & Fishing (Rules 23-26) 7.3 Special Category Vessels: NUC, RAM, CBD, Pilot & Anchored (Rules 27-31) 7.4 Sound and Light Signals: Manoeuvring, Warning & Fog (Rules 32-37)
8 Chapter 8: The IALA Maritime Buoyage System
8.1 Lateral Marks: System A and System B Comparison 8.2 Cardinal Marks: Quadrants, Topmarks, Colours & Light Sequences 8.3 Isolated Danger, Safe Water, Special & Emergency Wreck Marks
9 Chapter 9: Meteorology, Synoptic Systems & Depressions
9.1 Atmospheric Pressure, Isobars & Buys Ballot's Law 9.2 Air Masses & The Anatomy of a Frontal Depression 9.3 Passage of a Frontal Depression: Pressure, Wind & Cloud Changes 9.4 Anticyclones, Ridges, Cols & Troughs
10 Chapter 10: Local Coastal Weather, Fog & Forecasts
10.1 Coastal Effects: Sea & Land Breezes, Katabatic Winds & Funnelling 10.2 Fog Formation: Advection Fog, Radiation Fog & Sea Smoke 10.3 Beaufort Wind Scale & Maritime Forecast Interpretation
11 Chapter 11: Passage Planning & Pilotage Under SOLAS Chapter V
11.1 SOLAS Chapter V Regulations & The 4 Stages of Passage Planning 11.2 Routing Strategy, Tidal Windows, Fuel Planning & Contingencies 11.3 Pilotage Plans, Clearing Bearings, Leading Lines & Soundings 11.4 Night Pilotage, Light Characteristics & Dipping Distances
12 Chapter 12: Marine Safety, Emergencies & GMDSS Communications
12.1 GMDSS Architecture, VHF DSC & Marine Radio Distress Procedures 12.2 Emergency Distress Equipment: EPIRB, SART, Navtex & Pyrotechnics 12.3 Heavy Weather Seamanship, Stability & Man Overboard Recovery
5.1 Secondary Port Calculations: Time & Height Differences
Key Takeaways Explain This Topic AI
Secondary Ports do not have dedicated daily prediction tables; their times and heights are calculated by applying tabulated differences to a designated Standard Port.
ATT Part II gives HW and LW time differences against specified Standard Port reference times. Read those column headings and interpolate separately for HW and LW.
Height differences in ATT Part II are tabulated against four primary tidal datums: Mean High Water Springs (MHWS), Mean High Water Neaps (MHWN), Mean Low Water Neaps (MLWN), and Mean Low Water Springs (MLWS).
Use the time basis printed in the tables. In the UT-based UK exercise here, complete interpolation in UT and add one hour for BST only to the final result.
Mathematical signs (+ or -) must be strictly maintained throughout calculations; subtracting a negative difference is equivalent to adding that height or time.
Last updated: November 2026
5.1 Secondary Port Calculations: Time & Height Differences
Note
While major commercial hubs feature full daily predictions in Admiralty Tide Tables (ATT) Part I, thousands of smaller anchorages and coastal marinas are designated as Secondary Ports in ATT Part II. Navigators predict secondary port tides by applying mathematical time and height differences to a primary Standard Port .
Standard Ports vs. Secondary Ports
The UK Hydrographic Office cannot publish 365-day tables for every coastal inlet. The appropriate regional ATT volume organizes tidal coverage into two tiers:
Standard Ports : Ports with published daily predictions (e.g., Dover, Portsmouth, Plymouth, Brest). ATT Part I tabulates daily times and heights of High Water (HW) and Low Water (LW) in the stated time zone, with the applicable prediction guidance.
Secondary Ports : Coastal locations whose tides mirror a designated Standard Port with predictable time lags and range variations. ATT Part II lists secondary ports by geographical index number, tabulating differences relative to their parent Standard Port.
Because secondary ports lie within the same co-tidal system as their parent Standard Port, astronomical variations reproduce at the secondary port with consistent mathematical offsets.
Architecture of Admiralty Tide Tables (ATT) Part II
ATT Part II displays differences in a standardized tabular format containing three core datasets:
Position & Reference Port : Port index number, geographical coordinates (lat/long), and the assigned Standard Port.
Time Differences (HW and LW) : Tabulated against specified Standard Port clock times; these vary by location, so use the actual column headings.
Height Differences : Tabulated against four primary tidal levels of the Standard Port:
MHWS (Mean High Water Springs) : Height difference at mean spring high water.
MHWN (Mean High Water Neaps) : Height difference at mean neap high water.
MLWN (Mean Low Water Neaps) : Neap low water difference.
MLWS (Mean Low Water Springs) : Spring low water difference.
Sample ATT Part II Extract: Secondary Port 'Sandy Cove'
Secondary Port Position Ref Standard Port HW Diff: 0000/1200 HW Diff: 0600/1800 LW Diff: 0000/1200 LW Diff: 0600/1800 MHWS (6.0m) MHWN (4.8m) MLWN (1.8m) MLWS (0.6m)
- No. 1422 Sandy Cove 50°24.5'N 003°32.1'W Port Victoria +0040 +0020 +0050 +0030 +0.6m +0.2m -0.1m -0.3m
- Time Standards & British Summer Time (BST)
Read the time zone printed for the port and differences table. The fictional table in this section uses Universal Time (UT / GMT) .
Warning
The Reference Time Rule : Interpolate against the clock times and time basis printed in the table. For this UT-based exercise, add 1 hour for BST only to the final prediction. Do not add summer time to a time difference or interpolate a BST clock time against UT column headings.
Linear Interpolation Protocol
Standard Port daily tides rarely match exact reference hours or datum levels, requiring linear interpolation :
1. Time Interpolation
For Standard Port time T T T between reference times T 1 T_1 T 1 and T 2 T_2 T 2 with differences D 1 D_1 D 1 and D 2 D_2 D 2 : Interpolated Diff = D 1 + ( T − T 1 T 2 − T 1 ) × ( D 2 − D 1 ) \text{Interpolated Diff} = D_1 + \left( \frac{T - T_1}{T_2 - T_1} \right) \times (D_2 - D_1) Interpolated Diff = D 1 + ( T 2 − T 1 T − T 1 ) × ( D 2 − D 1 ) Secondary Time = T + Interpolated Diff \text{Secondary Time} = T + \text{Interpolated Diff} Secondary Time = T + Interpolated Diff
2. Height Interpolation
For Standard Port height H H H between datum levels H 1 H_1 H 1 and H 2 H_2 H 2 with differences Δ H 1 \Delta H_1 Δ H 1 and Δ H 2 \Delta H_2 Δ H 2 : Interpolated Height Diff = Δ H 1 + ( H − H 1 H 2 − H 1 ) × ( Δ H 2 − Δ H 1 ) \text{Interpolated Height Diff} = \Delta H_1 + \left( \frac{H - H_1}{H_2 - H_1} \right) \times (\Delta H_2 - \Delta H_1) Interpolated Height Diff = Δ H 1 + ( H 2 − H 1 H − H 1 ) × ( Δ H 2 − Δ H 1 ) Secondary Height = H + Interpolated Height Diff \text{Secondary Height} = H + \text{Interpolated Height Diff} Secondary Height = H + Interpolated Height Diff
Comprehensive Worked Numerical Scenario
A yacht plans to enter Sandy Cove on 15 June (draught 1.8m, BST active).
Standard Port (Port Victoria) Daily Predictions
From ATT Part I: HW at 0430 UT (5.4m); LW at 1045 UT (1.1m).
Datums: MHWS = 6.0m, MHWN = 4.8m, MLWN = 1.8m, MLWS = 0.6m.
Calculation Steps
High Water Time (Sandy Cove) :
0430 UT is between 0000 (+0040) and 0600 (+0020).
Elapsed: 270/360 min = 0.75. Change: (+20) - (+40) = -20 min.
Diff at 0430: + 40 + ( 0.75 × − 20 ) = + 0025 +40 + (0.75 \times -20) = \mathbf{+0025} + 40 + ( 0.75 × − 20 ) = + 0025 .
Secondary HW: 0430 + 0025 = 0455 UT 0430 + 0025 = \mathbf{0455\text{ UT}} 0430 + 0025 = 0455 UT ( 0555 BST \mathbf{0555\text{ BST}} 0555 BST ).
High Water Height (Sandy Cove) :
5.4m is midway between MHWN (4.8m) and MHWS (6.0m) (range 1.2m, offset 0.6m, ratio 0.5).
Diff change: ( + 0.6 ) − ( + 0.2 ) = + 0.4 m (+0.6) - (+0.2) = +0.4\text{m} ( + 0.6 ) − ( + 0.2 ) = + 0.4 m .
Diff at 5.4m: + 0.2 + ( 0.5 × 0.4 ) = + 0.4 m +0.2 + (0.5 \times 0.4) = \mathbf{+0.4\text{m}} + 0.2 + ( 0.5 × 0.4 ) = + 0.4 m .
Secondary HW Height: 5.4 m + 0.4 m = 5.8 m 5.4\text{m} + 0.4\text{m} = \mathbf{5.8\text{m}} 5.4 m + 0.4 m = 5.8 m .
Low Water Time (Sandy Cove) :
1045 UT is between 0600 (+0030) and 1200 (+0050).
Elapsed: 285/360 min = 0.792. Change: (+50) - (+30) = +20 min.
Diff at 1045: + 30 + ( 0.792 × 20 ) = + 30 + 16 = + 0046 +30 + (0.792 \times 20) = +30 + 16 = \mathbf{+0046} + 30 + ( 0.792 × 20 ) = + 30 + 16 = + 0046 .
Secondary LW: 1045 + 0046 = 1131 UT 1045 + 0046 = \mathbf{1131\text{ UT}} 1045 + 0046 = 1131 UT ( 1231 BST \mathbf{1231\text{ BST}} 1231 BST ).
Low Water Height (Sandy Cove) :
1.1m is between MLWS (0.6m) and MLWN (1.8m) (range 1.2m, offset 0.5m, ratio 0.5 / 1.2 = 0.417 0.5/1.2 = 0.417 0.5/1.2 = 0.417 ).
Diff change: ( − 0.1 ) − ( − 0.3 ) = + 0.2 m (-0.1) - (-0.3) = +0.2\text{m} ( − 0.1 ) − ( − 0.3 ) = + 0.2 m .
Diff at 1.1m: − 0.3 + ( 0.417 × 0.2 ) = − 0.3 + 0.083 = − 0.2 m -0.3 + (0.417 \times 0.2) = -0.3 + 0.083 = \mathbf{-0.2\text{m}} − 0.3 + ( 0.417 × 0.2 ) = − 0.3 + 0.083 = − 0.2 m .
Secondary LW Height: 1.1 m + ( − 0.2 m ) = 0.9 m 1.1\text{m} + (-0.2\text{m}) = \mathbf{0.9\text{m}} 1.1 m + ( − 0.2 m ) = 0.9 m .
Admiralty Pro-Forma Summary
- Parameter High Water (HW) Low Water (LW)
- Standard Port Time (UT) 0430 1045
- Interpolated Time Difference +0025 +0046
- Secondary Port Time (UT) 0455 1131
- Summer Time Correction (BST) +0100 +0100
- Secondary Port Time (BST) 0555 BST 1231 BST
- Standard Port Height 5.4m 1.1m
- Interpolated Height Difference +0.4m -0.2m
- Secondary Port Height 5.8m 0.9m
- Practical Examination Pitfalls
Sign Confusion : Height differences often carry negative signs (e.g., -0.2m ). Adding a negative decreases height ( 1.1 m + ( − 0.2 m ) = 0.9 m 1.1\text{m} + (-0.2\text{m}) = 0.9\text{m} 1.1 m + ( − 0.2 m ) = 0.9 m ). Reversing signs risks groundings.
Column Misalignment : Always interpolate HW predictions against HW difference columns, and LW predictions against LW difference columns.
Double Summer Time Addition : Keep all arithmetic in UT until the final step, then add 1 hour for BST once.