Study guide

12.1 Supplemental Restraint System: Safe Handling & Diagnostics

Saudi Skill Verification Program - Auto Electrician Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Assessment Overview

About the SVP Auto Electrician Assessment

2 Electrical Fundamentals, Circuit Laws & Schematics

1.1 Ohm's Law, Watt's Law & Circuit Calculations 1.2 Automotive Wiring Schematics & DIN / SAE Standards 1.3 Series, Parallel & Series-Parallel Circuits

3 Relays, Fuses, Circuit Protection & Switching

2.1 Fuses, Fusible Links & Circuit Breakers 2.2 Relays, Solenoids & Electromagnetic Controls 2.3 Switches, Connectors & Terminal Pin Diagnostics

4 Digital Multimeter Diagnostics & Circuit Fault Tracing

3.1 Digital Multimeter Operation, Settings & Safety 3.2 Voltage Drop Testing & Systematic Fault Isolation 3.3 Parasitic Drain Testing & Quiescent Current Isolation

5 Automotive Batteries, Chemistry & Service

4.1 Lead-Acid Battery Chemistry & Construction 4.2 State of Charge, Conductance & Carbon Pile Load Testing 4.3 Battery Service, Maintenance & Safe Charging Protocols

6 Starting Systems, Starter Motors & Cranking Circuits

5.1 Starter Motor Principles, Construction & Drive Mechanisms 5.2 Starter Solenoids, Relays & Control Circuits 5.3 Cranking Circuit Diagnostics & Voltage Drop Analysis

7 Charging Systems, Alternators & Voltage Regulation

6.1 Alternator Construction, Electromagnetic Induction & Rectification 6.2 Voltage Regulation, Smart Charging & Field Control 6.3 Charging System Testing, Ripple Voltage & Diode Diagnostics

8 Automotive Sensors, ECU Operation & Multiplex Networking

7.1 ECU Architecture, Power, Ground & Reference Voltage Circuits 7.2 Engine & Chassis Sensors: Operation and Signal Testing 7.3 Oxygen Sensors, Air-Fuel Ratio Sensors & Fuel Trim Diagnostics 7.4 CAN Bus, LIN Bus & In-Vehicle Network Diagnostics

9 Vehicle Lighting, Accessories, Workshop Safety & EV Basics

8.1 Exterior & Interior Lighting Circuits and Diagnostics 8.2 Horn, Wiper, Power Accessories & Signaling Circuits 8.3 Workshop Safety, Chemical Hazards & Welding Precautions 8.4 High-Voltage Electric Vehicle (EV/HEV) Electrical Safety

10 Ignition Systems, Fuel Injection & Emission Control Electrics

9.1 Ignition System Fundamentals: Primary & Secondary Circuits 9.2 Electronic Ignition, Timing & Misfire Diagnosis 9.3 Electronic Fuel Injection Circuits, Fuel Pump & Injector Testing 9.4 EGR Valves & Emission-Control Actuator Diagnostics

11 Engine Cooling Fan, Instrument Panel & HVAC Electrical Systems

10.1 Engine Cooling Fan & Temperature Warning Circuits 10.2 Instrument Cluster, Gauges & Warning Lamp Diagnostics 10.3 Instrument-Panel Sensors, Senders & Switch Inputs 10.4 HVAC Heating, Blower & Ventilation Electrical Control 10.5 Air Conditioning Electrical Control & Compressor Clutch Circuits

12 Chassis Electrical: Braking, Transmission & Steering Systems

11.1 Anti-lock Braking & Electronic Brake Force Distribution Diagnostics 11.2 Automatic Transmission Electrical Controls & Solenoid Testing 11.3 Electronic Power Steering (EPS) Diagnostics

13 Comfort, Security & Occupant-Safety Systems

12.1 Supplemental Restraint System: Safe Handling & Diagnostics 12.2 Security, Immobiliser & Central Locking Systems 12.3 Cruise Control, Power Seats, Mirrors & Sunroof Circuits 12.4 Workplace Communication, Service Documentation & Diagnostic Software

12.1 Supplemental Restraint System: Safe Handling & Diagnostics

Key Takeaways Explain This Topic AI

An airbag initiator can be fired by a few hundred milliamperes, which is within the output of an ordinary ohmmeter, so squib circuits must never be measured with a multimeter or a test light.

The SRS control module holds a backup capacitor that can deploy an airbag after the battery is disconnected, so the manufacturer's stand-down period must be observed before any work.

SRS harnesses and connectors are coloured yellow and contain shorting bars that link the two squib wires together whenever the connector is unplugged.

A live airbag module must be carried with the trim face away from the body and stored face up on a flat surface so it cannot launch itself if it deploys.

SRS faults are diagnosed only with a scan tool, and the module itself measures squib resistance through its own protected circuitry.

Last updated: September 2026

What the Competency Standard Requires

Repair Supplemental Restraint System (SRS) requires you to check the SRS using a scanner , identify faulty components including the spiral cable, seat belt, SRS unit, control module and sensors and replace them, and inspect continuity of the wiring harness and repair or replace it as required.

Note the wording carefully. The scan tool is named as the diagnostic instrument. Nowhere does the standard invite you to put a multimeter on a squib circuit, and doing so can deploy an airbag into your face.

SRS Architecture

Component Function

SRS / airbag control module Contains the deployment logic, an internal accelerometer, a backup capacitor and the fault memory. Usually mounted on the transmission tunnel near the vehicle centre of gravity

Front, side and satellite impact sensors Accelerometers or pressure sensors that confirm an impact and its direction

  • Squib (initiator) The electrically fired igniter inside each airbag and pretensioner, typically about 2-3 ohms
  • Airbag modules Driver, passenger, side, curtain and knee bags

Seat belt pretensioners Pyrotechnic or mechanical devices that remove slack from the belt milliseconds before the bag inflates

Occupant classification / weight sensor Suppresses or reduces passenger bag deployment for a child or an empty seat

Seat belt buckle switches Tell the module which occupants are restrained so deployment force can be tailored

Clockspring (spiral cable) Carries the driver airbag squib circuit, horn and steering wheel switches across the rotating column

  • Warning lamp Prove-out at key-on, then extinguishes if the self-test passes
  • Design features that exist purely for safety

Yellow harness and connectors. Every SRS circuit is coloured yellow specifically so a technician can recognise it instantly and avoid cutting, splicing or probing it.

Shorting bars. SRS connectors contain a metal bar that automatically links the two squib wires together the moment the connector is unplugged. This prevents static or induced voltage from building a potential across the initiator. Forcing a probe into such a connector can lift the shorting bar and remove the protection.

Twisted pair wiring to cancel induced electromagnetic interference.

Redundant sensing. The module normally requires agreement between the internal accelerometer and a remote impact sensor before it will deploy, so a single sensor fault does not cause an accidental deployment.

The Rules That Keep You Alive

Switch the ignition off, disconnect the battery negative terminal, and wait the manufacturer's specified stand-down period. This is commonly between one and ten minutes depending on the vehicle, and it exists so the module's backup capacitor discharges. Look up the figure for the specific vehicle rather than assuming.

Never measure a squib circuit with an ohmmeter, a test light or a continuity buzzer. An initiator can fire on a few hundred milliamperes, and a typical multimeter on the ohms range or a test light can supply that. The control module measures squib resistance internally through a current-limited circuit, and the scan tool reports the result.

Never apply battery voltage to an airbag connector for any reason.

Carry a live airbag module with the trim cover facing away from your body , so that an unexpected deployment moves the module away from you rather than into you.

Store a live module face up on a flat, clear surface. Face down, a deployment turns the module into a projectile.

Do not expose airbag modules to temperatures above the manufacturer's limit , commonly around 93 degrees Celsius , and keep them clear of paint ovens, heat guns and welding.

Never strike, drop or subject the module to impact , and never attempt to open, repair or test a module.

Do not fit aftermarket seat covers over seats containing side airbags , and do not place accessories on the dash above a passenger airbag.

Disconnect the module before any welding , following the pre-welding isolation protocol in section 8.3.

Treat a deployed module as hazardous waste and dispose of both deployed and undeployed units through the approved route. An undeployed module removed from a scrapped vehicle is an explosive device.

Diagnosing SRS Faults

The method is short because the tool list is short.

Observe the prove-out. The SRS lamp should illuminate at key-on for a few seconds and then extinguish. A lamp that stays on indicates a stored fault. A lamp that never illuminates is just as serious, because it means the driver has no warning capability at all and someone may have removed the bulb to hide a fault.

Read the codes with a scan tool , recording whether each is current or historic and how many ignition cycles ago it was set.

Interpret the code type:

Code family Typical meaning Usual cause

Squib circuit resistance high The circuit has more resistance than expected A connector not fully seated, corrosion, or a broken clockspring conductor

  • Squib circuit resistance low or shorted Two conductors touching Chafed harness under a seat, or a crushed wire
  • Squib circuit shorted to earth or to battery Insulation damage Harness pinched by a seat rail or trim fixing
  • Impact sensor circuit or internal Sensor or wiring Corrosion at a wheel arch or door-mounted sensor

Occupant classification Weight sensing Spilled liquid, seat mat damage, or a calibration needed after seat removal

  • Module internal Control unit May require replacement and coding
  • Crash data stored Deployment recorded The module is locked and must be replaced, never simply cleared

Clear the code and re-test. A code that clears and stays clear through several ignition cycles and a road test was likely a poor connection. A code that returns immediately identifies a hard fault.

Inspect the physical circuit only with the system de-energised, the stand-down period observed and the connectors unplugged so the shorting bars are engaged.

The clockspring

The clockspring (spiral cable) is the single most common SRS fault and also appears in the cruise control and horn competencies because it carries those circuits too.

Symptoms include an intermittent driver airbag code, a horn that works only at certain steering positions, dead steering wheel switches and, on some vehicles, a steering angle sensor fault.

The ribbon breaks from repeated flexing, especially if the wheel has been rotated while the clockspring was disconnected.

Centring is critical. Before removing a clockspring, set the road wheels straight ahead and lock the steering. A replacement clockspring arrives with a locking tab that must stay in place until the wheel is fitted. Fitting an off-centre clockspring tears the ribbon at one extreme of lock, often days later.

After a Deployment

Repairing a deployed system is not a matter of fitting a new bag.

Read and record the crash data before replacing anything.

Replace every deployed component - airbag modules, pretensioners and any single-use bracket.

Replace the control module where the manufacturer requires it. Many modules lock permanently once crash data is written and cannot be reset.

Inspect and replace the impact sensors that recorded the event, plus any harness that has been heat damaged or stretched.

Inspect seat belts thoroughly. A belt that carried load in a collision must be replaced, including the retractor, even where it looks undamaged.

Replace, do not repair, the wiring. SRS harness splicing is prohibited by most manufacturers; the correct repair is a new harness section or connector kit.

Programme and configure the new module to the vehicle and then verify with a full scan and a lamp prove-out.

Seat Belts and Pretensioners

The competency standard names the seat belt among SRS components, and for good reason: the belt is the primary restraint and the airbag is supplemental to it.

Component Function Check

Retractor with emergency locking mechanism Locks under vehicle deceleration or rapid webbing extraction Pull sharply; the webbing must lock. Tilt-test the retractor where accessible

Pyrotechnic pretensioner Fires milliseconds before the airbag to remove slack Diagnosed only by scan tool; handle exactly as an airbag squib

Load limiter Allows controlled webbing payout to reduce chest loading Not serviceable; replace the assembly

Buckle switch Tells the module whether the occupant is belted Check status in live data; drink spillage is the common failure

Webbing Restrains the occupant Inspect the full length for cuts, fraying, chemical damage and heat damage

A belt that has restrained an occupant in a collision, or whose pretensioner has fired, must be replaced as an assembly. Never attempt to reset, re-wind or reload a fired pretensioner.

Customer Communication

SRS work carries an obligation to explain clearly:

If the SRS lamp is on, the system may not deploy in a collision . Say that plainly rather than describing it as a warning light problem.

Explain that the airbag supplements the seat belt and does not replace it.

Record the SRS lamp state on the job card at check-in and at hand-back. This protects both the customer and the workshop.

Never suggest disconnecting a bag, removing a bulb or fitting a resistor to extinguish a lamp. All three defeat a safety system and expose the workshop to serious liability.

Faults the Practical Assessment Likes to Present

Intermittent driver airbag code plus an erratic horn - clockspring.

Passenger airbag code after seat removal - occupant classification calibration not performed.

Side airbag code after a trim repair - pinched harness under the seat rail.

SRS lamp that never lights at key-on - removed bulb or open lamp circuit hiding a real fault.

Multiple SRS codes after a jump-start - poor connection or a voltage event; check supply before condemning the module.