Study guide

10.1 Engine Cooling Fan & Temperature Warning Circuits

Saudi Skill Verification Program - Auto Electrician Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Assessment Overview

About the SVP Auto Electrician Assessment

2 Electrical Fundamentals, Circuit Laws & Schematics

1.1 Ohm's Law, Watt's Law & Circuit Calculations 1.2 Automotive Wiring Schematics & DIN / SAE Standards 1.3 Series, Parallel & Series-Parallel Circuits

3 Relays, Fuses, Circuit Protection & Switching

2.1 Fuses, Fusible Links & Circuit Breakers 2.2 Relays, Solenoids & Electromagnetic Controls 2.3 Switches, Connectors & Terminal Pin Diagnostics

4 Digital Multimeter Diagnostics & Circuit Fault Tracing

3.1 Digital Multimeter Operation, Settings & Safety 3.2 Voltage Drop Testing & Systematic Fault Isolation 3.3 Parasitic Drain Testing & Quiescent Current Isolation

5 Automotive Batteries, Chemistry & Service

4.1 Lead-Acid Battery Chemistry & Construction 4.2 State of Charge, Conductance & Carbon Pile Load Testing 4.3 Battery Service, Maintenance & Safe Charging Protocols

6 Starting Systems, Starter Motors & Cranking Circuits

5.1 Starter Motor Principles, Construction & Drive Mechanisms 5.2 Starter Solenoids, Relays & Control Circuits 5.3 Cranking Circuit Diagnostics & Voltage Drop Analysis

7 Charging Systems, Alternators & Voltage Regulation

6.1 Alternator Construction, Electromagnetic Induction & Rectification 6.2 Voltage Regulation, Smart Charging & Field Control 6.3 Charging System Testing, Ripple Voltage & Diode Diagnostics

8 Automotive Sensors, ECU Operation & Multiplex Networking

7.1 ECU Architecture, Power, Ground & Reference Voltage Circuits 7.2 Engine & Chassis Sensors: Operation and Signal Testing 7.3 Oxygen Sensors, Air-Fuel Ratio Sensors & Fuel Trim Diagnostics 7.4 CAN Bus, LIN Bus & In-Vehicle Network Diagnostics

9 Vehicle Lighting, Accessories, Workshop Safety & EV Basics

8.1 Exterior & Interior Lighting Circuits and Diagnostics 8.2 Horn, Wiper, Power Accessories & Signaling Circuits 8.3 Workshop Safety, Chemical Hazards & Welding Precautions 8.4 High-Voltage Electric Vehicle (EV/HEV) Electrical Safety

10 Ignition Systems, Fuel Injection & Emission Control Electrics

9.1 Ignition System Fundamentals: Primary & Secondary Circuits 9.2 Electronic Ignition, Timing & Misfire Diagnosis 9.3 Electronic Fuel Injection Circuits, Fuel Pump & Injector Testing 9.4 EGR Valves & Emission-Control Actuator Diagnostics

11 Engine Cooling Fan, Instrument Panel & HVAC Electrical Systems

10.1 Engine Cooling Fan & Temperature Warning Circuits 10.2 Instrument Cluster, Gauges & Warning Lamp Diagnostics 10.3 Instrument-Panel Sensors, Senders & Switch Inputs 10.4 HVAC Heating, Blower & Ventilation Electrical Control 10.5 Air Conditioning Electrical Control & Compressor Clutch Circuits

12 Chassis Electrical: Braking, Transmission & Steering Systems

11.1 Anti-lock Braking & Electronic Brake Force Distribution Diagnostics 11.2 Automatic Transmission Electrical Controls & Solenoid Testing 11.3 Electronic Power Steering (EPS) Diagnostics

13 Comfort, Security & Occupant-Safety Systems

12.1 Supplemental Restraint System: Safe Handling & Diagnostics 12.2 Security, Immobiliser & Central Locking Systems 12.3 Cruise Control, Power Seats, Mirrors & Sunroof Circuits 12.4 Workplace Communication, Service Documentation & Diagnostic Software

10.1 Engine Cooling Fan & Temperature Warning Circuits

Key Takeaways Explain This Topic AI

A radiator thermo switch typically closes near 92-97 degrees Celsius and reopens about 5-8 degrees lower, giving the switching hysteresis that stops relay chatter.

The engine coolant temperature sensor feeding the ECU and the temperature gauge sender feeding the instrument panel are usually two separate devices.

An air conditioning request normally forces the cooling fan on regardless of coolant temperature, to protect condenser head pressure.

A fan that runs continuously from key-on points to a shorted thermo switch, an open coolant temperature sensor circuit or welded relay contacts.

Electric cooling fans can start without warning while the ignition is off, so never leave hands near the blades on a hot engine.

Last updated: September 2026

What the Competency Standard Requires

Repair Engine Cooling Fan and Electrical Circuit is the sixth competency unit inside Repair Electrical Systems of Vehicle. Its performance criteria require you to inspect fan operation and repair faults, inspect the water temperature gauge and its sensor or switch , inspect the cooling fan relay and fuse , and inspect and repair the wiring harness .

That pairing of the fan with the temperature gauge is deliberate: both depend on accurate coolant temperature information, and a single bad earth can upset both.

Four Cooling Fan Control Architectures

Architecture Control device Typical current Recognition

Belt-driven viscous (thermal) clutch Bimetallic coil and silicone fluid coupling None electrical Fan mounted on the water pump pulley, no wiring

Single-speed electric with thermo switch Temperature switch screwed into the radiator or thermostat housing, driving a relay 12-25 A Two-wire switch in the radiator tank

Two-speed electric Two relays plus a series dropping resistor, or two motors 12-25 A low, 25-40 A high A ballast resistor pack near the fan shroud

Pulse-width-modulated brushless fan module Electronic module receiving a duty-cycle command from the ECU, often over LIN Up to 60-80 A peak Three or four wires to a control module bolted to the shroud

The thermo switch

A thermo switch is a simple thermostatic contact immersed in coolant. A typical single-speed switch closes near 92-97 degrees Celsius and reopens about 5-8 degrees lower . That deliberate gap is hysteresis , and it exists so the fan does not chatter on and off around a single temperature point. Two-speed switches contain two contact sets at different temperatures, for example low speed at 92 degrees and high speed at 99 degrees.

Test a thermo switch by measuring continuity across it while the engine warms, or by removing it and heating it in a controlled water bath with a thermometer. Bridging the two switch terminals with a fused jumper should run the fan immediately; if it does, the switch is faulty and the rest of the circuit is sound.

The relay and its drive

Most electric fan circuits use a standard ISO relay with DIN 72552 terminals: terminal 30 from a high-current fuse, terminal 87 to the fan motor, terminal 86 from switched ignition, and terminal 85 switched to earth either by the thermo switch or by an ECU low-side driver. On ECU-controlled systems the thermo switch is replaced entirely by the engine coolant temperature sensor signal and a software threshold, which lets the manufacturer vary fan-on temperature by operating condition.

The air conditioning override. When the air conditioning compressor is engaged, the ECU or the pressure switch normally forces the fan on regardless of coolant temperature. This protects condenser head pressure and is why a fan that only fails to run with the air conditioning on points to the request circuit rather than the temperature circuit.

  • Diagnosing Cooling Fan Faults
  • Fan never runs

Work outward from the motor:

Bridge the thermo switch terminals with a fused jumper, or command the fan on with a bidirectional scan tool. If the fan runs, the temperature input or the ECU driver is at fault, not the motor.

Check the high-current fuse and the relay. Swap in a known-good identical relay before testing further.

Measure voltage at the fan connector with the fan commanded on. Voltage present and no rotation means the motor or its earth has failed.

Bench the motor on a fused direct supply and measure current draw. A motor drawing far more than specification has worn brushes or dry bearings; a motor drawing nothing is open.

Voltage-drop the feed and earth under running load. More than about 0.5 V total across the circuit starves the motor and causes slow running and overheating.

Fan runs continuously from key-on

This is the mirror image and equally common:

  • Cause Confirmation
  • Thermo switch shorted internally Unplug the switch; if the fan stops, the switch is at fault
  • Relay contacts welded closed Remove the relay; if the fan stops, replace the relay

Coolant temperature sensor circuit open The ECU sees an implausibly hot or cold signal and defaults the fan on as a protective strategy; scan data shows an extreme value

Wiring chafed to earth on the low-side drive Disconnect the ECU connector; if the fan still runs, the harness is shorted

Note the fourth row: an open temperature sensor circuit commonly commands the fan on , because a full-time fan is the safe default. Technicians who assume a fan-on fault must be a shorted switch will miss this.

Fan runs but the engine still overheats

The fault is usually not electrical at all. Check the coolant level, the thermostat, the radiator core for blockage and the water pump. Confirm the fan is rotating in the correct direction and that the shroud is present and intact, because a missing shroud can halve airflow.

The Temperature Gauge and Warning Lamp Circuit

The competency standard lists the water temperature gauge and its sender in the same breath as the fan, so treat them as one system.

The gauge sender is usually a separate negative temperature coefficient (NTC) thermistor with a single wire, earthed through its threads into the cylinder head or housing. Its resistance falls as coolant temperature rises.

The engine coolant temperature sensor used by the ECU is typically a two-wire NTC device with its own dedicated earth, so it is unaffected by a corroded thread.

On bimetallic thermal gauges an instrument voltage regulator supplies a stabilised average voltage, commonly around 5 V or 10 V , so the reading does not swing with charging voltage. If that regulator fails, the fuel and temperature gauges usually read wrongly together, which is a valuable clue.

Modern clusters use stepper-motor gauges driven from a digital value the ECU broadcasts over the vehicle network, so the "sender" wire may not exist at all.

Reading the symptom pattern

Symptom Likely cause

Gauge reads permanently cold, engine runs normally Sender wire open, sender failed open, or an earth fault at the sender thread

  • Gauge reads permanently hot from key-on Sender wire shorted to earth
  • Temperature gauge and fuel gauge both wrong Instrument voltage regulator or a shared cluster earth

Gauge normal but the ECU reports the wrong temperature Separate coolant temperature sensor circuit, not the gauge circuit

Warning lamp on with a normal gauge Separate overheat switch or a lamp-driver fault in the cluster

The Heater and Blower Connection

The Skill Verification Program pairs the cooling fan unit with checks on the heater core, blower and fuse , because they share coolant and cabin airflow. A blower motor that has failed also removes the heater core's ability to shed heat into the cabin, and a heater core blocked with scale can mimic a cooling system fault. Full blower control detail is covered in section 10.4; the point here is that an overheating complaint should always include a check that the heater delivers hot air, since cool heater output with a hot engine strongly suggests low coolant level or an air lock.

Safety Rules for Cooling Fan Work

An electric cooling fan can start without warning even with the ignition off , because many run-on strategies keep the circuit live while the engine cools. Disconnect the fan connector or the battery negative terminal before putting hands near the blades.

Never remove a pressure cap from a hot system. Coolant above 100 degrees Celsius flashes to steam the moment pressure is released and causes severe scald injuries. Wait until the upper hose can be squeezed comfortably by hand.

Ethylene glycol coolant is toxic and sweet-tasting, so it must be captured and disposed of properly and never left in an open container where it may be mistaken for a drink.

Keep tools, sleeves and test leads clear of the fan and belts whenever the engine is running.

Support the vehicle correctly on axle stands before working under it on a lower fan shroud or radiator fixing.