Study guide
9.1 Ignition System Fundamentals: Primary & Secondary Circuits
Saudi Skill Verification Program - Auto Electrician Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Assessment Overview
About the SVP Auto Electrician Assessment
2 Electrical Fundamentals, Circuit Laws & Schematics
1.1 Ohm's Law, Watt's Law & Circuit Calculations 1.2 Automotive Wiring Schematics & DIN / SAE Standards 1.3 Series, Parallel & Series-Parallel Circuits
3 Relays, Fuses, Circuit Protection & Switching
2.1 Fuses, Fusible Links & Circuit Breakers 2.2 Relays, Solenoids & Electromagnetic Controls 2.3 Switches, Connectors & Terminal Pin Diagnostics
4 Digital Multimeter Diagnostics & Circuit Fault Tracing
3.1 Digital Multimeter Operation, Settings & Safety 3.2 Voltage Drop Testing & Systematic Fault Isolation 3.3 Parasitic Drain Testing & Quiescent Current Isolation
5 Automotive Batteries, Chemistry & Service
4.1 Lead-Acid Battery Chemistry & Construction 4.2 State of Charge, Conductance & Carbon Pile Load Testing 4.3 Battery Service, Maintenance & Safe Charging Protocols
6 Starting Systems, Starter Motors & Cranking Circuits
5.1 Starter Motor Principles, Construction & Drive Mechanisms 5.2 Starter Solenoids, Relays & Control Circuits 5.3 Cranking Circuit Diagnostics & Voltage Drop Analysis
7 Charging Systems, Alternators & Voltage Regulation
6.1 Alternator Construction, Electromagnetic Induction & Rectification 6.2 Voltage Regulation, Smart Charging & Field Control 6.3 Charging System Testing, Ripple Voltage & Diode Diagnostics
8 Automotive Sensors, ECU Operation & Multiplex Networking
7.1 ECU Architecture, Power, Ground & Reference Voltage Circuits 7.2 Engine & Chassis Sensors: Operation and Signal Testing 7.3 Oxygen Sensors, Air-Fuel Ratio Sensors & Fuel Trim Diagnostics 7.4 CAN Bus, LIN Bus & In-Vehicle Network Diagnostics
9 Vehicle Lighting, Accessories, Workshop Safety & EV Basics
8.1 Exterior & Interior Lighting Circuits and Diagnostics 8.2 Horn, Wiper, Power Accessories & Signaling Circuits 8.3 Workshop Safety, Chemical Hazards & Welding Precautions 8.4 High-Voltage Electric Vehicle (EV/HEV) Electrical Safety
10 Ignition Systems, Fuel Injection & Emission Control Electrics
9.1 Ignition System Fundamentals: Primary & Secondary Circuits 9.2 Electronic Ignition, Timing & Misfire Diagnosis 9.3 Electronic Fuel Injection Circuits, Fuel Pump & Injector Testing 9.4 EGR Valves & Emission-Control Actuator Diagnostics
11 Engine Cooling Fan, Instrument Panel & HVAC Electrical Systems
10.1 Engine Cooling Fan & Temperature Warning Circuits 10.2 Instrument Cluster, Gauges & Warning Lamp Diagnostics 10.3 Instrument-Panel Sensors, Senders & Switch Inputs 10.4 HVAC Heating, Blower & Ventilation Electrical Control 10.5 Air Conditioning Electrical Control & Compressor Clutch Circuits
12 Chassis Electrical: Braking, Transmission & Steering Systems
11.1 Anti-lock Braking & Electronic Brake Force Distribution Diagnostics 11.2 Automatic Transmission Electrical Controls & Solenoid Testing 11.3 Electronic Power Steering (EPS) Diagnostics
13 Comfort, Security & Occupant-Safety Systems
12.1 Supplemental Restraint System: Safe Handling & Diagnostics 12.2 Security, Immobiliser & Central Locking Systems 12.3 Cruise Control, Power Seats, Mirrors & Sunroof Circuits 12.4 Workplace Communication, Service Documentation & Diagnostic Software
9.1 Ignition System Fundamentals: Primary & Secondary Circuits
Key Takeaways Explain This Topic AI
An ignition coil steps 12 V primary voltage up to 8,000-40,000 V secondary through a turns ratio of roughly 100:1 to 150:1.
Contact-breaker ignition uses a condenser of about 0.20-0.30 microfarads to suppress arcing across the points and sharpen primary current collapse.
Dwell angle and point gap are inversely related: opening the point gap reduces dwell angle, and closing the gap increases it.
Carbon-core suppression HT leads typically measure about 5-15 kilohms per metre, and most manufacturers reject any single lead above roughly 25 kilohms.
Required firing voltage rises with plug gap, cylinder pressure and lean mixtures, while available voltage falls with a weak coil or leaking insulation.
Last updated: September 2026
Why the Ignition Circuit Is Its Own Competency
The Skill Verification Program occupational standard for Automobile Electrician lists Repair Ignition System as a separate competency unit inside the Repair Electrical Systems of Vehicle standard. Its performance criteria require you to check and replace the ignition switch, ignition coil and resistor , inspect high-tension (HT) cables for damaged insulation and out-of-specification resistance, verify the electrical power source and charging system , clean or replace spark plugs , replace fuses with correct ratings, check the distributor, distributor cap and rotor , and test ignition system sensors .
An auto electrician owns this circuit end to end because almost every failure in it is electrical rather than mechanical.
The Two Circuits Inside Every Ignition System
- Primary circuit Secondary circuit
- Voltage 12-14 V (battery or charging voltage) 8,000-40,000 V
- Current 3-8 A typical Milliamperes
- Conductor Normal primary cable, small gauge Heavily insulated HT lead or integrated coil boot
Components Battery, ignition switch, ballast resistor, coil primary winding, switching device (points or transistor), condenser Coil secondary winding, distributor cap and rotor where fitted, HT leads, spark plug
Common faults Corroded switch, open resistor, burned points, failed driver Tracking, carbon paths, cracked insulation, worn plug electrodes
The coil bridges the two. Its primary winding is a few hundred turns of relatively heavy wire; its secondary winding is tens of thousands of turns of very fine wire. The turns ratio of roughly 100:1 to 150:1 multiplies voltage when the primary magnetic field collapses.
Typical coil winding resistances
Coil type Primary resistance Secondary resistance
Ballast-resistor coil (points or early electronic) 1.0-1.5 ohms plus a separate 1.2-1.6 ohm ballast 6,000-15,000 ohms
- Non-ballast 12 V coil 1.5-3.0 ohms 6,000-15,000 ohms
- Distributorless twin-tower coil 0.4-1.0 ohm 8,000-15,000 ohms
- Coil-on-plug with internal driver Not measurable at the connector Not measurable at the connector
Always compare against the manufacturer's repair manual figure. Many coil-on-plug units contain the switching transistor inside the coil body, so an ohmmeter across the connector proves nothing. A resistance test on those coils is a common technician trap.
The Ignition Switch and the Ballast Resistor
Using DIN 72552 terminal designations, the ignition switch feeds:
Terminal 30 - permanent unswitched battery positive into the switch.
Terminal 15 - switched positive, live in RUN and START. This is the normal coil feed, routed through the ballast resistor where one is fitted.
Terminal 15a - the output from the ballast resistor to the coil positive terminal.
Terminal 50 - starter solenoid control, live only in START.
The ballast resistor solves a cranking problem. During cranking, battery voltage collapses to perhaps 9-10 V, which would weaken the spark exactly when the engine needs it most. The system therefore uses a coil with a low-resistance primary winding and inserts a ballast resistor in series for normal running. During cranking, a bypass circuit fed from the starter solenoid shorts the ballast out and applies full available voltage directly to the coil.
Two classic faults follow from this design:
Engine starts while cranking but dies the instant the key returns to RUN - the ballast resistor is open-circuit. The bypass carried the coil during cranking; when the bypass dropped out, the coil lost its feed.
Engine will not start when cold but runs once hot - the bypass wire from the solenoid is open, so the coil runs on reduced voltage during cranking.
A ballast resistor is a resistance wire or ceramic block and must never be replaced with ordinary wire, which would over-drive the coil and burn the points or the driver transistor.
Contact Breaker Points and the Condenser
Older vehicles still common in light commercial fleets use a contact breaker (CB) point set inside the distributor, driven by a cam on the distributor shaft. The competency standard explicitly lists C.B Point and Condenser as required knowledge.
Point gap is typically 0.40-0.50 mm at full cam lift.
Dwell angle is the number of degrees of distributor rotation for which the points remain closed and the coil is charging. Point gap and dwell angle are inversely related : widening the gap makes the points open earlier and close later, so dwell decreases ; closing the gap increases dwell.
The condenser (capacitor) sits in parallel with the points, typically 0.20-0.30 microfarads . It absorbs the inductive surge at the moment the points open, which stops the points arcing and makes primary current collapse faster, raising secondary voltage.
Failure signatures worth memorising:
- Symptom Likely cause
- Badly burned, blue-black pitted points after short service Wrong, open or disconnected condenser
Metal transferred from one point face to the other forming a pip and crater Condenser capacitance wrong for the coil
- Dwell changes as engine speed rises Worn distributor shaft bushes or a worn breaker cam
- Weak spark and misfire under load Excessive point gap, low dwell, insufficient coil charge time
Distributor, Cap, Rotor and HT Leads
On a points system the distributor performs three jobs: it triggers the primary circuit, it distributes secondary voltage to the correct cylinder, and it advances timing through centrifugal weights and a vacuum diaphragm.
Inspection checklist required by the competency standard:
Cap - check for hairline cracks, carbon tracking lines between towers, corroded or eroded brass segments, and moisture ingress. A carbon track is a permanent low-resistance path, so the cap must be replaced rather than cleaned.
Rotor - check the tip for erosion and the centre carbon contact for wear. Measure rotor resistance where a suppression rotor is used, commonly about 1,000-5,000 ohms.
Centre carbon brush and spring inside the cap - a stuck or worn brush causes a total no-spark condition.
Shaft end float and side play - excessive play changes dwell and timing together.
HT lead testing. Modern suppression leads use a carbon-impregnated or wound ferrite core to limit radio interference. Measure each lead end to end with a digital multimeter on the ohms range:
Carbon-core leads: roughly 5,000-15,000 ohms per metre .
Most manufacturers reject any single lead above about 25,000 ohms , and any lead reading open circuit.
Always compare leads of similar length against each other. One outlier is usually the failed lead.
Check insulation in a darkened bay with the engine running: visible blue arcing to the block, the manifold or a bracket confirms breakdown. Never pull a live HT lead off by the wire; use insulated pliers on the boot only, and remember that secondary voltage can exceed 30,000 V.
Spark Plugs
Property What it means Service point
Gap Distance between centre and earth electrode, typically 0.7-1.1 mm Set with a wire feeler gauge to the manual figure; never gap a fine-wire platinum or iridium plug by levering on the centre electrode
Heat range How quickly the plug conducts heat away from the firing tip A colder plug than specified fouls; a hotter plug than specified risks pre-ignition
Reach Threaded length A plug that is too long can contact the piston; too short leaves carbon build-up in the exposed threads
Resistor plug Internal 4,000-6,000 ohm resistor Required on vehicles with electronic modules; substituting a non-resistor plug can cause interference faults
Reading plugs is a diagnostic skill the practical assessment rewards. Light tan or grey deposits indicate normal combustion. Dry black soot indicates a rich mixture or weak ignition. Wet black oily deposits indicate oil control failure. A white, blistered or melted tip indicates overheating or pre-ignition. Torque plugs to specification - typically 20-30 Nm for a 14 mm gasket-seat plug and less for taper-seat designs - because both under-torque and over-torque ruin heat transfer.
Required Voltage Versus Available Voltage
Every spark event is a race between two figures:
Required voltage is the voltage needed to ionise the gap. It rises with a wider plug gap, higher cylinder pressure under heavy load or boost, a lean mixture, and worn electrodes.
Available voltage is the maximum the coil can deliver. It falls with a weak coil, high primary resistance, a low battery, high HT lead resistance, or insulation leakage.
A misfire under load with a perfect idle is the classic signature of a small margin between the two. At idle the required voltage is low enough for a tired coil to cope; under load the required voltage climbs past what the system can supply.