Study guide

2.1 Four-Stroke Petrol Engine Operation, Thermodynamics & Cylinder Configuration

Saudi Skill Verification Program - Light Vehicle Mechanic Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Assessment Overview

1.1 Program Identity, Current Test Rules & Evidence Limits 1.2 Practical Assessment Evidence, Safe Workflow & Task Preparation

2 Engine Fundamentals, Four-Stroke Cycle & Internal Components

2.1 Four-Stroke Petrol Engine Operation, Thermodynamics & Cylinder Configuration 2.2 Cylinder Block, Pistons, Rings, Connecting Rods & Crankshaft Assemblies 2.3 Cylinder Head, Valvetrain Architectures & Timing Drive Systems

3 Engine Mechanical Diagnostics & Overhaul Procedures

3.1 Compression Testing & Cylinder Leak-Down Diagnostics 3.2 Manifold Vacuum Diagnostics & Engine Oil Pressure Testing 3.3 Cylinder Head Gasket Failure Analysis, Warp Measurement & Valve Sealing

4 Engine Lubrication, Cooling & Climate Control

4.1 Engine Lubrication Principles, Oil Viscosity, Filtration & Pressure Relief 4.2 Engine Cooling System Architecture, Thermostats, Radiators & Water Pumps 4.3 Gulf Climate Cooling Performance, Electric Fan Controls & Coolant Chemistry 4.4 Automotive Air Conditioning Operation, Diagnosis & Refrigerant Service

5 Petrol Fuel Delivery & Injection Systems

5.1 Fuel Tank Assemblies, Electric Pumps, Pressure Regulation & Line Safety 5.2 Port Fuel Injection (PFI) vs. Gasoline Direct Injection (GDI) Technologies 5.3 Air Induction, Throttle Bodies, Idle Air Control & Mass Airflow / MAP Sensors

6 Ignition Systems & Engine Management

6.1 Ignition Principles, Spark Plug Heat Ranges & Secondary Voltage Patterns 6.2 Distributorless & Coil-on-Plug (COP) Ignition Architectures 6.3 Crankshaft/Camshaft Position Sensors, Timing Advance & Knock Control

7 Exhaust, Emission Control & Aftertreatment Systems

7.1 Exhaust Manifolds, Gaskets, Catalytic Converters & Thermal Efficiency 7.2 Oxygen Sensors, Air-Fuel Ratio Sensors & Fuel Trim Diagnostics 7.3 Evaporative Emission Control (EVAP) & Positive Crankcase Ventilation (PCV)

8 Automotive Electrical Fundamentals, Batteries & Charging

8.1 Electrical Fundamentals, Ohm's Law & 12V Lead-Acid Battery Diagnostics 8.2 Cranking Systems, Starter Solenoids & Voltage Drop Testing 8.3 Alternators, Rectifiers, Regulators & Charging Circuit Diagnosis

9 On-Board Diagnostics (OBD-II) & Systematic Troubleshooting

9.1 OBD-II Architecture, Standardization & Generic DTC Structure 9.2 Live PID Streaming, Freeze Frame Capture & Readiness Monitors 9.3 Systematic Diagnostic Workflow: Verify, Isolate, Repair & Validate

10 Clutches & Manual Transmissions

10.1 Friction Clutch Construction, Pressure Plates, Flywheels & Release Bearings 10.2 Hydraulic Clutch Actuation, Master/Slave Cylinders & Bleeding Procedures 10.3 Manual Gearbox Internal Operation, Synchromesh Units & Gear Selection

11 Automatic Transmissions, Drivelines & Differentials

11.1 Torque Converters, Planetary Gearsets & Automatic Transmission Fluid (ATF) 11.2 Front-Wheel-Drive Halfshafts, Constant Velocity (CV) Joints & Boots 11.3 Rear-Wheel-Drive Propeller Shafts, Universal Joints & Differential Operation

12 Hydraulic Braking Systems & ABS

12.1 Hydraulic Principles, Dual Tandem Master Cylinders & Vacuum Boosters 12.2 Disc & Drum Brake Mechanical Service, Calipers & Rotors 12.3 Brake Fluid Chemistry (DOT 3, 4, 5.1), Bleeding Methods & Anti-Lock Brakes (ABS)

13 Steering, Suspension, Wheel Alignment & Balancing

13.1 Steering Systems: Rack-and-Pinion, Hydraulic Power Steering & EPS 13.2 Suspension Architectures: MacPherson Struts, Multi-Link & Shock Absorbers 13.3 Wheel Alignment Geometry (Camber, Caster, Toe, SAI) & Tire Wear Analysis 13.4 Wheel Balancing, Runout Diagnosis & Safe Wheel Installation

14 Workshop Safety, Precision Measurement & Fastener Torquing

14.1 Personal Protective Equipment, Chemical Safety & Shop Hazard Management 14.2 Vehicle Lifting Equipment, Two-Post Lift Positioning & Hydraulic Jacks 14.3 Precision Measuring Instruments (Micrometers, Dial Gauges) & Fastener Torquing

2.1 Four-Stroke Petrol Engine Operation, Thermodynamics & Cylinder Configuration

Key Takeaways Explain This Topic AI

The four-stroke Otto cycle completes one full thermodynamic cycle over 720° of crankshaft rotation (two full revolutions), requiring four distinct piston strokes: Intake, Compression, Power (Expansion), and Exhaust.

Ignition timing is initiated prior to Top Dead Center (typically 10°–15° BTDC) to ensure the progressive combustion flame front (~20–30 m/s) generates peak cylinder pressure (40–60 bar) at approximately 10°–15° After Top Dead Center (ATDC) for optimal crankshaft mechanical leverage.

Valve overlap is the brief period around TDC between the exhaust and intake strokes where both valves are open simultaneously, utilizing exhaust gas column momentum to scavenge residual gases and initiate the fresh intake charge.

Engine displacement is determined by cylinder swept volume (Vd = π/4 × d² × s), while the compression ratio is defined as CR = (Vd + Vc) / Vc; higher compression ratios directly improve theoretical Otto cycle thermal efficiency.

Engine layout, crankshaft geometry, firing order, counterweights, balance shafts, and mount design work together to control primary forces, secondary forces, and rocking couples; use the engine-specific firing order.

Last updated: September 2026

2.1 Four-Stroke Petrol Engine Operation, Thermodynamics & Cylinder Configuration

Automotive light vehicle technicians must possess a thorough mechanical and thermodynamic understanding of internal combustion fundamentals. The spark-ignition petrol engine operates on the four-stroke Otto cycle , first commercialized by Nikolaus Otto in 1876. Translating reciprocating linear motion into continuous rotational torque requires precise synchronization of gas exchange, valve timing, fuel delivery, and high-voltage ignition.

  • Note
  • Core Engine Kinematics & Geometric Definitions

Top Dead Center (TDC): The uppermost position of piston travel within the cylinder bore, representing the point of minimum cylinder volume ( V c V_c V c ​ , clearance volume).

Bottom Dead Center (BDC): The lowermost position of piston travel, representing the point of maximum cylinder volume ( V t = V d + V c V_t = V_d + V_c V t ​ = V d ​ + V c ​ ).

Bore ( d d d ): The internal diameter of the finished cylinder bore, expressed in millimeters (mm) or inches (in).

Stroke ( s s s ): The linear distance traveled by the piston between TDC and BDC, equal to twice the crankshaft throw radius ( s = 2 × r c r a n k s = 2 \times r_{crank} s = 2 × r cr ank ​ ).

720° Cycle Relationship: Because each stroke corresponds to 180° of crankshaft rotation, completing all four strokes requires 4 × 180 ∘ = 720 ∘ 4 \times 180^\circ = 720^\circ 4 × 18 0 ∘ = 72 0 ∘ of crankshaft rotation (two full crankshaft revolutions) for every single rotation of the camshaft ( 360 ∘ 360^\circ 36 0 ∘ ), establishing a strict 2:1 rotational gear ratio.

The Four-Stroke Otto Cycle: Step-by-Step Breakdown INTAKE STROKE COMPRESSION STROKE POWER STROKE EXHAUST STROKE

(0° to 180°) (180° to 360°) (360° to 540°) (540° to 720°)

  • Intake Exhaust Intake Exhaust Intake Exhaust Intake Exhaust
  • OPEN CLOSED CLOSED CLOSED CLOSED CLOSED CLOSED OPEN
  • | | | | | | | |
  • v | | | | | | ^
  • +-------------+ +-------------+ +-------------+ +-------------+
  • | (Air/ | | (Charge | | (SPARK) | | (Exhaust |
  • | Fuel) | | Compressed)| | Combustion | | Gases |
  • | | | | ^ | | | | | ^ |
  • | v | | | | | v | | | |
  • | [PISTON] | | [PISTON] | | [PISTON] | | [PISTON] |
  • | | | | | | | | | | | |
  • | v | | ^ | | v | | ^ |
  • +-------------+ +-------------+ +-------------+
  • Downward Upward Downward Upward
  • Motion (BDC) Motion (TDC) Motion (BDC) Motion (TDC)
  • 1. The Intake Stroke (Crankshaft 0° to 180°)

Kinematic Action: The piston moves downward from TDC to BDC.

Valve Status: The intake valve opens slightly before TDC (typically 5°–15° BTDC) and remains open past BDC (typically 35°–50° ABDC); the exhaust valve is closed.

Thermodynamic Behavior: As the piston descends, the volume inside the cylinder expands rapidly. This volumetric expansion causes cylinder pressure to drop below atmospheric pressure ( 101.3 kPa 101.3\text{ kPa} 101.3 kPa or 14.7 psi 14.7\text{ psi} 14.7 psi at sea level), creating a partial vacuum (atmospheric depression) ranging from − 40 kPa -40\text{ kPa} − 40 kPa to − 70 kPa -70\text{ kPa} − 70 kPa (12 to 21 in-Hg manifold vacuum in port-injected engines at idle/part throttle). Atmospheric pressure pushes the ambient air charge through the throttle body, intake runner, and open intake valve into the low-pressure cylinder.

Intake Valve Closing (IVC) Dynamics: Closing the intake valve after BDC appears counterintuitive, but it takes advantage of incoming air column inertia (ram effect). At high engine RPM, the incoming column of air possesses substantial kinetic energy; leaving the valve open after BDC allows this air momentum to continue packing into the cylinder even as the piston begins its initial upward rise, maximizing volumetric efficiency.

2. The Compression Stroke (Crankshaft 180° to 360°)

Kinematic Action: The piston travels upward from BDC to TDC.

Valve Status: Both intake and exhaust valves are firmly seated and hermetically sealed.

Thermodynamic Behavior: As the trapped air-fuel mixture is compressed into the combustion chamber clearance volume ( V c V_c V c ​ ), mechanical work is converted into internal thermal energy (adiabatic compression). Dynamic compression raises in-cylinder pressure to 10 – 15 bar 10–15\text{ bar} 10–15 bar ( 145 – 220 psi 145–220\text{ psi} 145–220 psi ) and mixture temperature to 350 ∘ C– 450 ∘ C 350^\circ\text{C}–450^\circ\text{C} 35 0 ∘ C –45 0 ∘ C . This rapid temperature rise vaporizes liquid fuel droplets into a homogeneous combustible gas, preparing the molecules for rapid chemical oxidation.

3. The Power / Expansion Stroke (Crankshaft 360° to 540°)

Kinematic Action: The piston is driven downward from TDC to BDC by high-pressure expanding combustion gases. This is the only stroke in the cycle that produces net positive mechanical work.

Valve Status: Both intake and exhaust valves remain tightly closed.

Combustion & Ignition Timing: The spark plug discharges prior to TDC (typically 10°–15° BTDC at curb idle, advancing to 30°–42° BTDC under high-speed cruise). Petrol combustion is a controlled deflagration rather than an instantaneous detonation; the flame front propagates outward from the spark plug electrodes at approximately 20 – 30 m/s 20–30\text{ m/s} 20–30 m/s . Initiating ignition BTDC gives the flame front sufficient time to consume the air-fuel mixture so that peak cylinder pressure (typically 40 to 60 bar / 600 to 900 psi) is reached precisely at 10° to 15° After Top Dead Center (ATDC) . This specific crankshaft angle provides the connecting rod and crankshaft throw journal with optimum mechanical leverage to generate maximum turning torque.

4. The Exhaust Stroke (Crankshaft 540° to 720°)

Kinematic Action: The piston travels upward from BDC to TDC.

Valve Status: The exhaust valve opens well before BDC (typically 40°–55° BBDC) and closes slightly after TDC (typically 5°–15° ATDC); the intake valve remains closed until near TDC.

Blowdown & Scavenging Dynamics: Opening the exhaust valve before BDC initiates the blowdown phase . Although the power stroke is ending, in-cylinder pressure at 50° BBDC remains at 3 – 5 bar 3–5\text{ bar} 3–5 bar ( 45 – 75 psi 45–75\text{ psi} 45–75 psi ). This residual pressure allows high-temperature exhaust gases to begin rushing out into the exhaust manifold under their own pressure differential before the piston reaches BDC. As the piston rounds BDC and ascends to TDC, it mechanically sweeps the remaining burnt combustion products out through the open exhaust port, clearing the cylinder for the next incoming charge.

Valve Overlap and Inertia Scavenging

Valve overlap is the brief angular duration—measured in crankshaft degrees—around TDC during which the intake valve has begun opening while the exhaust valve has not yet fully closed . TDC (Overlap Period)

  • \ /
  • Intake Opens \ / Exhaust Closes
  • (e.g., 10° BTDC) X (e.g., 10° ATDC)
  • / \
  • / \
  • Exhaust Stroke Intake Stroke
  • Physics of Inertia Scavenging

As the high-velocity column of exhaust gas accelerates down the exhaust runner and manifold header, it develops significant kinetic mass and inertia. When the piston reaches TDC, this exiting exhaust gas column creates a localized low-pressure depression (suction wave) directly behind the exhaust valve head. Because the intake valve is already cracked open during overlap, this depression pulls the fresh intake charge into the cylinder before the piston even begins descending, while simultaneously drawing out the last traces of burnt exhaust gas trapped in the clearance volume.

High-RPM Benefit: Greatly enhances volumetric efficiency, increases engine power output, and cools the exhaust valve head.

Low-RPM / Idle Penalty: At curb idle, low exhaust gas velocity prevents effective inertia scavenging. Instead, the intake manifold vacuum can draw exhaust gases backward into the intake runner (reversion), causing combustion instability, rough idling, and elevated unburnt hydrocarbon ( H C HC H C ) emissions. Variable Valve Timing (VVT) resolves this compromise by retarding the intake cam or advancing the exhaust cam at idle to minimize overlap, and increasing overlap under mid-range cruising loads.

Mathematical Formulas & Worked Calculations

Automotive technicians must calculate engine displacement, compression ratios, and thermal efficiency when performing engine overhauls, cylinder boring, or performance reconditioning.

1. Cylinder Swept Volume ( V d V_d V d ​ )

The swept volume (displacement) of a single cylinder represents the volume displaced by the piston crown moving between BDC and TDC: V d = π 4 × d 2 × s V_d = \frac{\pi}{4} \times d^2 \times s V d ​ = 4 π ​ × d 2 × s

Where:

  • V d V_d V d ​ = Cylinder swept volume (cubic centimeters, cc \text{cc} cc or cm 3 \text{cm}^3 cm 3 )
  • d d d = Cylinder bore diameter (centimeters, cm \text{cm} cm )
  • s s s = Piston stroke length (centimeters, cm \text{cm} cm )

2. Total Engine Displacement ( V t o t a l V_{total} V t o t a l ​ ) V t o t a l = V d × N V_{total} = V_d \times N V t o t a l ​ = V d ​ × N

Where N N N equals the total number of engine cylinders.

3. Compression Ratio ( C R CR CR )

The static compression ratio compares the total cylinder volume when the piston is at BDC ( V t V_t V t ​ ) to the clearance volume remaining when the piston is at TDC ( V c V_c V c ​ ): C R = V d + V c V c = V d V c + 1 CR = \frac{V_d + V_c}{V_c} = \frac{V_d}{V_c} + 1 CR = V c ​ V d ​ + V c ​ ​ = V c ​ V d ​ ​ + 1

To find clearance volume when swept volume and compression ratio are known: V c = V d C R − 1 V_c = \frac{V_d}{CR - 1} V c ​ = CR − 1 V d ​ ​

Worked Example: 4-Cylinder Passenger Vehicle Engine

Given Specifications:

  • Cylinder bore ( d d d ) = 82.5 mm = 8.25 cm 82.5\text{ mm} = 8.25\text{ cm} 82.5 mm = 8.25 cm
  • Piston stroke ( s s s ) = 92.8 mm = 9.28 cm 92.8\text{ mm} = 9.28\text{ cm} 92.8 mm = 9.28 cm
  • Number of cylinders ( N N N ) = 4 4 4
  • Combustion chamber clearance volume ( V c V_c V c ​ ) = 49.63 cc 49.63\text{ cc} 49.63 cc

Step 1: Calculate single-cylinder swept volume ( V d V_d V d ​ ): V d = π 4 × ( 8.25 ) 2 × 9.28 = 0.785398 × 68.0625 × 9.28 = 496.06 cc ≈ 496.1 cc V_d = \frac{\pi}{4} \times (8.25)^2 \times 9.28 = 0.785398 \times 68.0625 \times 9.28 = 496.06\text{ cc} \approx 496.1\text{ cc} V d ​ = 4 π ​ × ( 8.25 ) 2 × 9.28 = 0.785398 × 68.0625 × 9.28 = 496.06 cc ≈ 496.1 cc

Step 2: Calculate total engine displacement ( V t o t a l V_{total} V t o t a l ​ ): V t o t a l = 496.06 cc × 4 = 1 , 984.24 cc ≈ 1.984 Liters (marketed as a 2.0L engine) V_{total} = 496.06\text{ cc} \times 4 = 1,984.24\text{ cc} \approx 1.984\text{ Liters (marketed as a 2.0L engine)} V t o t a l ​ = 496.06 cc × 4 = 1 , 984.24 cc ≈ 1.984 Liters (marketed as a 2.0L engine)

Step 3: Calculate the static compression ratio ( C R CR CR ): C R = 496.06 cc + 49.63 cc 49.63 cc = 545.69 cc 49.63 cc = 10.995 : 1 ≈ 11.0 : 1 CR = \frac{496.06\text{ cc} + 49.63\text{ cc}}{49.63\text{ cc}} = \frac{545.69\text{ cc}}{49.63\text{ cc}} = 10.995:1 \approx 11.0:1 CR = 49.63 cc 496.06 cc + 49.63 cc ​ = 49.63 cc 545.69 cc ​ = 10.995 : 1 ≈ 11.0 : 1

4. Theoretical Otto Cycle Thermal Efficiency ( η t h \eta_{th} η t h ​ )

Thermal efficiency dictates how effectively an engine converts the chemical heat energy of fuel into mechanical crankshaft work: η t h = 1 − 1 C R γ − 1 \eta_{th} = 1 - \frac{1}{CR^{\gamma - 1}} η t h ​ = 1 − C R γ − 1 1 ​

Where γ \gamma γ (gamma) is the ratio of specific heats for air ( ≈ 1.4 \approx 1.4 ≈ 1.4 ). For an engine with a 10.0 : 1 10.0:1 10.0 : 1 compression ratio: η t h = 1 − 1 10.0 1.4 − 1 = 1 − 1 10.0 0.4 = 1 − 1 2.512 = 1 − 0.398 = 0.602 ( 60.2 % theoretical ) \eta_{th} = 1 - \frac{1}{10.0^{1.4 - 1}} = 1 - \frac{1}{10.0^{0.4}} = 1 - \frac{1}{2.512} = 1 - 0.398 = 0.602 \quad (60.2\%\text{ theoretical}) η t h ​ = 1 − 10. 0 1.4 − 1 1 ​ = 1 − 10. 0 0.4 1 ​ = 1 − 2.512 1 ​ = 1 − 0.398 = 0.602 ( 60.2% theoretical )

In real-world light vehicles, actual brake thermal efficiency ranges between 30% and 36% . The remaining energy is lost through:

  • Exhaust gas enthalpy heat rejection (~30%–35%)
  • Engine cooling system heat transfer (~25%–30%)
  • Internal mechanical friction and pumping losses (~5%–8%)
  • Cylinder Configurations, Firing Intervals & Engine Balance

Light vehicle engines are configured in several distinct geometric layouts depending on vehicle packaging, center-of-gravity targets, and NVH (Noise, Vibration, and Harshness) requirements.

Configuration Bank Angle Primary Vibration Balance Secondary Vibration Balance Firing Interval ( 720 ∘ / N 720^\circ / N 72 0 ∘ / N ) Common Light Vehicle Applications

Inline-4 (I4) 0 ∘ 0^\circ 0 ∘ (Single Bank) Inherent balance (pistons 1 & 4 oppose 2 & 3) Unbalanced (connecting rod angularity causes 2 × RPM 2\times\text{RPM} 2 × RPM vertical shake) 180 ∘ 180^\circ 18 0 ∘ Compact front-wheel-drive passenger sedans and crossovers.

Inline-6 (I6) 0 ∘ 0^\circ 0 ∘ (Single Bank) Perfect balance Perfect balance (forces and moments naturally cancel) 120 ∘ 120^\circ 12 0 ∘ Longitudinal rear-wheel-drive sedans and SUVs (e.g., BMW, Mercedes).

V6 (60°) 60 ∘ 60^\circ 6 0 ∘ Good balance with balance shaft Good balance with 6-throw crankshaft 120 ∘ 120^\circ 12 0 ∘ (Even firing) Mid-size sedans, crossovers, and minivans.

V6 (90°) 90 ∘ 90^\circ 9 0 ∘ Requires counterweights / balance shaft Requires split/splayed crankpins ( 30 ∘ 30^\circ 3 0 ∘ offset) 120 ∘ 120^\circ 12 0 ∘ (Even firing with split pins) Light trucks and vehicles sharing V8 manufacturing tooling.

Boxer-4 (Flat-4) 180 ∘ 180^\circ 18 0 ∘ (Opposed) Primary forces cancel , but cylinder offset can create a rocking couple Secondary forces largely cancel; overall smoothness still depends on crank and layout 180 ∘ 180^\circ 18 0 ∘ Subaru, Porsche (ultra-low center of gravity).

V8 (Cross-Plane) 90 ∘ 90^\circ 9 0 ∘ Balanced via heavy counterweights Balanced via 90° pin orientation 90 ∘ 90^\circ 9 0 ∘ Full-size SUVs, pickup trucks, and performance vehicles.

Firing Orders and Crankshaft Throw Spacing

Crankshaft throws are spaced radially to evenly divide the 720° cycle among the cylinders ( 720 ∘ / N 720^\circ / N 72 0 ∘ / N ):

Inline-4 Engines ( 180 ∘ 180^\circ 18 0 ∘ intervals): Firing order 1-3-4-2 (most common) or 1-2-4-3 . Cylinders 1 and 4 reach TDC together, while cylinders 2 and 3 are at BDC. Because connecting rods swing through an angle, pistons accelerate faster through the top half of their stroke than through the bottom half. This creates a secondary harmonic vibration occurring at twice engine speed ( 2 × RPM 2\times\text{RPM} 2 × RPM ). In engines larger than 2.0 L 2.0\text{L} 2.0 L , manufacturers incorporate twin counter-rotating balance shafts driven at twice engine speed to cancel this secondary shake.

Inline-6 Engines ( 120 ∘ 120^\circ 12 0 ∘ intervals): Firing order 1-5-3-6-2-4 . The 120° crank throws create mirror-image symmetry across the center main bearing, resulting in perfect primary and secondary natural mechanical balance without balance shafts.

V6 Engines ( 120 ∘ 120^\circ 12 0 ∘ intervals): Firing order typically 1-4-2-5-3-6 or 1-2-3-4-5-6 . In a 60° bank V6, six discrete crankpins produce natural 120° firing. In a 90° bank V6, standard crank throws would cause an uneven firing sequence alternating between 90° and 150°. To achieve smooth 120° even firing, crankshaft manufacturers incorporate splayed or split crankpins , machining a 30° offset into each rod journal pair.

V8 Engines ( 90 ∘ 90^\circ 9 0 ∘ intervals): Cross-plane crankshaft firing order 1-8-4-3-6-5-7-2 (GM/Chrysler) or 1-5-4-8-6-3-7-2 (Ford). The cross-plane layout features four crankpins oriented at 90° to one another in two perpendicular planes, requiring substantial counterweights to yield exceptional low-vibration operation at the expense of rotating assembly inertia.

Four-Stroke Events, Crank Angles & Valve Positions

Cycle Event / Phase Crankshaft Rotation Angle Piston Direction Intake Valve Status Exhaust Valve Status Cylinder Pressure & Thermodynamic State

Intake (Induction) 0 ∘ 0^\circ 0 ∘ to 180 ∘ 180^\circ 18 0 ∘ Downward (TDC to BDC) OPEN (opens ~10° BTDC, closes ~40° ABDC) CLOSED Below atmospheric pressure ( − 40 -40 − 40 to − 70 kPa -70\text{ kPa} − 70 kPa ); fresh air-fuel mixture fills expanding volume.

Compression 180 ∘ 180^\circ 18 0 ∘ to 360 ∘ 360^\circ 36 0 ∘ Upward (BDC to TDC) CLOSED CLOSED Pressure rises to 10 – 15 bar 10–15\text{ bar} 10–15 bar ( 145 – 220 psi 145–220\text{ psi} 145–220 psi ); temperature rises to 350 ∘ – 450 ∘ C 350^\circ–450^\circ\text{C} 35 0 ∘ –45 0 ∘ C via adiabatic heating.

Ignition Event 345 ∘ 345^\circ 34 5 ∘ to 350 ∘ 350^\circ 35 0 ∘ (~10°–15° BTDC) Upward approaching TDC CLOSED CLOSED Spark plug ignites charge; flame front initiates progressive deflagration wave ( 20 – 30 m/s 20–30\text{ m/s} 20–30 m/s ).

Power (Expansion) 360 ∘ 360^\circ 36 0 ∘ to 540 ∘ 540^\circ 54 0 ∘ Downward (TDC to BDC) CLOSED CLOSED Peak pressure of 40–60 bar reached at 10°–15° ATDC ; expanding gases force piston down, driving crankshaft.

Exhaust Blowdown 485 ∘ 485^\circ 48 5 ∘ to 540 ∘ 540^\circ 54 0 ∘ (~40°–55° BBDC) Downward approaching BDC CLOSED OPENS EARLY Residual pressure ( 3 – 5 bar 3–5\text{ bar} 3–5 bar ) expels high-temperature exhaust gases into manifold runner before BDC.

Exhaust Scavenging 540 ∘ 540^\circ 54 0 ∘ to 720 ∘ 720^\circ 72 0 ∘ Upward (BDC to TDC) CLOSED OPEN (closes ~10° ATDC) Piston sweeps remaining burnt gases out; cylinder pressure remains slightly above atmospheric ( 105 – 120 kPa 105–120\text{ kPa} 105–120 kPa ).

Valve Overlap 710 ∘ 710^\circ 71 0 ∘ to 10 ∘ 10^\circ 1 0 ∘ (~10° BTDC to 10° ATDC) Transitioning at TDC OPEN OPEN Gas column inertia in exhaust runner creates vacuum wave, pulling fresh intake charge into combustion chamber.

Loading diagram... Four-Stroke Otto Cycle Sequence & Crankshaft Kinematics