Study guide
12.3 Brake Fluid Chemistry (DOT 3, 4, 5.1), Bleeding Methods & Anti-Lock Brakes (ABS)
Saudi Skill Verification Program - Light Vehicle Mechanic Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Assessment Overview
1.1 Program Identity, Current Test Rules & Evidence Limits 1.2 Practical Assessment Evidence, Safe Workflow & Task Preparation
2 Engine Fundamentals, Four-Stroke Cycle & Internal Components
2.1 Four-Stroke Petrol Engine Operation, Thermodynamics & Cylinder Configuration 2.2 Cylinder Block, Pistons, Rings, Connecting Rods & Crankshaft Assemblies 2.3 Cylinder Head, Valvetrain Architectures & Timing Drive Systems
3 Engine Mechanical Diagnostics & Overhaul Procedures
3.1 Compression Testing & Cylinder Leak-Down Diagnostics 3.2 Manifold Vacuum Diagnostics & Engine Oil Pressure Testing 3.3 Cylinder Head Gasket Failure Analysis, Warp Measurement & Valve Sealing
4 Engine Lubrication, Cooling & Climate Control
4.1 Engine Lubrication Principles, Oil Viscosity, Filtration & Pressure Relief 4.2 Engine Cooling System Architecture, Thermostats, Radiators & Water Pumps 4.3 Gulf Climate Cooling Performance, Electric Fan Controls & Coolant Chemistry 4.4 Automotive Air Conditioning Operation, Diagnosis & Refrigerant Service
5 Petrol Fuel Delivery & Injection Systems
5.1 Fuel Tank Assemblies, Electric Pumps, Pressure Regulation & Line Safety 5.2 Port Fuel Injection (PFI) vs. Gasoline Direct Injection (GDI) Technologies 5.3 Air Induction, Throttle Bodies, Idle Air Control & Mass Airflow / MAP Sensors
6 Ignition Systems & Engine Management
6.1 Ignition Principles, Spark Plug Heat Ranges & Secondary Voltage Patterns 6.2 Distributorless & Coil-on-Plug (COP) Ignition Architectures 6.3 Crankshaft/Camshaft Position Sensors, Timing Advance & Knock Control
7 Exhaust, Emission Control & Aftertreatment Systems
7.1 Exhaust Manifolds, Gaskets, Catalytic Converters & Thermal Efficiency 7.2 Oxygen Sensors, Air-Fuel Ratio Sensors & Fuel Trim Diagnostics 7.3 Evaporative Emission Control (EVAP) & Positive Crankcase Ventilation (PCV)
8 Automotive Electrical Fundamentals, Batteries & Charging
8.1 Electrical Fundamentals, Ohm's Law & 12V Lead-Acid Battery Diagnostics 8.2 Cranking Systems, Starter Solenoids & Voltage Drop Testing 8.3 Alternators, Rectifiers, Regulators & Charging Circuit Diagnosis
9 On-Board Diagnostics (OBD-II) & Systematic Troubleshooting
9.1 OBD-II Architecture, Standardization & Generic DTC Structure 9.2 Live PID Streaming, Freeze Frame Capture & Readiness Monitors 9.3 Systematic Diagnostic Workflow: Verify, Isolate, Repair & Validate
10 Clutches & Manual Transmissions
10.1 Friction Clutch Construction, Pressure Plates, Flywheels & Release Bearings 10.2 Hydraulic Clutch Actuation, Master/Slave Cylinders & Bleeding Procedures 10.3 Manual Gearbox Internal Operation, Synchromesh Units & Gear Selection
11 Automatic Transmissions, Drivelines & Differentials
11.1 Torque Converters, Planetary Gearsets & Automatic Transmission Fluid (ATF) 11.2 Front-Wheel-Drive Halfshafts, Constant Velocity (CV) Joints & Boots 11.3 Rear-Wheel-Drive Propeller Shafts, Universal Joints & Differential Operation
12 Hydraulic Braking Systems & ABS
12.1 Hydraulic Principles, Dual Tandem Master Cylinders & Vacuum Boosters 12.2 Disc & Drum Brake Mechanical Service, Calipers & Rotors 12.3 Brake Fluid Chemistry (DOT 3, 4, 5.1), Bleeding Methods & Anti-Lock Brakes (ABS)
13 Steering, Suspension, Wheel Alignment & Balancing
13.1 Steering Systems: Rack-and-Pinion, Hydraulic Power Steering & EPS 13.2 Suspension Architectures: MacPherson Struts, Multi-Link & Shock Absorbers 13.3 Wheel Alignment Geometry (Camber, Caster, Toe, SAI) & Tire Wear Analysis 13.4 Wheel Balancing, Runout Diagnosis & Safe Wheel Installation
14 Workshop Safety, Precision Measurement & Fastener Torquing
14.1 Personal Protective Equipment, Chemical Safety & Shop Hazard Management 14.2 Vehicle Lifting Equipment, Two-Post Lift Positioning & Hydraulic Jacks 14.3 Precision Measuring Instruments (Micrometers, Dial Gauges) & Fastener Torquing
12.3 Brake Fluid Chemistry (DOT 3, 4, 5.1), Bleeding Methods & Anti-Lock Brakes (ABS)
Key Takeaways Explain This Topic AI
Brake fluids are strictly categorized under FMVSS 116 / SAE J1703: glycol-based DOT 3, DOT 4, and DOT 5.1 are hygroscopic and mutually compatible, whereas silicone-based DOT 5 is non-hygroscopic, incompatible with glycol, and strictly prohibited in ABS/ESC systems.
Glycol brake fluids naturally absorb 1% to 2% atmospheric moisture annually; water accumulation exceeding 3% drops boiling points by up to 100°C, causing vapor lock where fluid boils into compressible steam and the brake pedal collapses to the floor.
Hydraulic bleeding techniques include two-person manual bleeding, positive pressure bleeding (0.7 to 1.0 bar / 10 to 15 psi), and automated scan-tool ABS bleeding, which is mandatory to cycle internal modulator solenoids and secondary accumulators when air enters the Hydraulic Control Unit (HCU).
Wheel Speed Sensors (WSS) deliver wheel rotational velocity to the ABS ECU: passive Variable Reluctance (VR) sensors generate an analog AC sine wave that fades below 5 km/h, while active Hall Effect / magnetoresistive sensors output a digital square wave down to 0 km/h with directional detection.
The ABS Hydraulic Control Unit executes four rapid electro-hydraulic phases (Normal Braking, Pressure Hold, Pressure Dump/Release, and Pressure Re-apply) cycling 15 to 20 times per second to prevent wheel lockup, preserve steering control, and integrate with TCS and ESC.
Last updated: September 2026
12.3 Brake Fluid Chemistry (DOT 3, 4, 5.1), Bleeding Methods & Anti-Lock Brakes (ABS)
Modern automotive braking systems rely on high-performance hydraulic fluid acting as the non-compressible power transmission medium, supervised by microcomputer-controlled electro-hydraulic anti-lock systems. Understanding the chemical classification of brake fluids, the physics of hygroscopic degradation, specialized bleeding techniques, and the electro-hydraulic control logic of Anti-Lock Braking Systems (ABS) and Electronic Stability Control (ESC) is mandatory for light vehicle mechanics certified under the Saudi Skill Verification Program (SVP).
- Note
- Core Brake Fluid Standards (FMVSS 116 / SAE J1703 / ISO 4925)
Dry Boiling Point: Minimum boiling temperature of new, unexposed fluid (0.0% moisture content).
Wet Boiling Point: Standardized equilibrium-reflux boiling point after controlled water exposure; it is a laboratory classification value, not a universal calendar age.
Kinematic Viscosity at -40°C: Some ESC/ABS modulators specify a low-viscosity fluid for cold and rapid valve operation; use the exact OEM fluid class.
Brake Fluid Chemistry & Regulatory Classifications
Automotive brake fluids must maintain precise viscosity across wide thermal extremes (-40°C to +260°C), lubricate internal metal pistons and rubber seals, prevent internal corrosion, and resist thermal breakdown. BRAKE FLUID BOILING POINT COMPARISON
- Fluid Type Dry Boiling Point (0% H2O) Wet Boiling Point (3.7% H2O)
- ------------------------------------------------------------------------
- DOT 3 205°C (401°F) 140°C (284°F)
- DOT 4 230°C (446°F) 155°C (311°F)
- DOT 5.1 260°C (500°F) 180°C (356°F)
- DOT 5 (Sil.) 260°C (500°F) [Non-hygroscopic; use only where specified]
- Polyalkylene Glycol-Based Fluids: DOT 3, DOT 4 & DOT 5.1
DOT 3 (Polyalkylene Glycol Ether):
Specifications: Minimum Dry Boiling Point of 205°C (401°F) ; Minimum Wet Boiling Point of 140°C (284°F) .
Properties: Formulated from glycol ethers. Clear to pale amber in color. Common in older passenger cars and economy light commercial vehicles. It absorbs moisture over time; test and replace at the interval and by the method specified by the vehicle manufacturer.
DOT 4 (Glycol Ether with Borate Esters):
Specifications: Minimum Dry Boiling Point of 230°C (446°F) ; Minimum Wet Boiling Point of 155°C (311°F) .
Properties: Contains borate esters that chemically react with and bind absorbed water molecules into boric acid complexes, partially neutralizing their adverse thermal effects and preserving a higher wet boiling point. The standard factory-fill fluid in modern passenger cars and SUVs.
DOT 4 Low Viscosity (DOT 4 LV / ISO 4925 Class 6): Features a kinematic viscosity at -40°C of ≤ 750 mm²/s (compared to 1,500 mm²/s for standard DOT 4). Required only where the vehicle manufacturer specifies that low-viscosity class; standard DOT 4 is not an automatic substitute.
DOT 5.1 (High-Performance Glycol / Borate Ester):
Specifications: Minimum Dry Boiling Point of 260°C (500°F) ; Minimum Wet Boiling Point of 180°C (356°F) .
Properties: Advanced non-silicone glycol formulation. Combines the ultra-high boiling temperature of silicone with low kinematic viscosity (≤ 900 mm²/s at -40°C). It is generally glycol-compatible with DOT 3 and DOT 4, but compatibility does not authorize a change of specification. Use DOT 5.1 only when it meets the vehicle requirement; ambient temperature alone is not a reason to upgrade or mix fluids.
Silicone-Based Brake Fluid: DOT 5
Specifications: Minimum Dry Boiling Point of 260°C (500°F) ; Minimum Wet Boiling Point of 180°C (356°F) .
Properties: Formulated from polydimethylsiloxane (silicone) polymer, dyed a mandatory distinct purple color. Silicone fluid is completely non-hygroscopic (it does not absorb water) and does not harm automotive paint finishes.
- Caution
- Strict Contraindications for Silicone DOT 5
PROHIBITED IN ABS/ESC VEHICLES: Silicone fluid entrains microscopic air bubbles when subjected to the high-frequency cycling (15 to 20 Hz) of ABS solenoid valves and pump pistons. This aeration causes a permanently spongy brake pedal that cannot be bled out.
IMMISCIBILITY HAZARD: DOT 5 cannot be mixed with glycol fluids (DOT 3, 4, 5.1). If mixed, the fluids separate into two distinct chemical phases, forming a thick gelatinous sludge that swells rubber seals, blocks master cylinder compensating ports, and causes complete brake failure.
WATER POOLING: Because DOT 5 does not absorb water, any condensation entering the system pools as pure, free liquid water at the lowest points (the caliper bores). In hot braking conditions, this free water boils at just 100°C (212°F) , precipitating sudden, total vapor lock!
Hygroscopic Degradation, Testing & Hydraulic Bleeding Methods
Glycol-based brake fluids are naturally hygroscopic —they actively absorb water vapor directly from the atmosphere through reservoir cap breather vents, microscopic pores in flexible rubber brake hoses, and caliper piston seals. Under typical operating conditions, brake fluid absorbs 1.5% to 3.0% water by volume every 12 to 24 months .
The Vapor Lock Mechanism
As brake fluid absorbs moisture, its boiling point drops rapidly. If moisture content reaches 3% to 4% , the fluid's boiling point decreases by up to 80°C to 100°C :
During sustained braking (such as descending mountain passes in the Asir region or aggressive highway deceleration in high ambient desert heat), caliper temperatures can easily reach 150°C to 200°C .
When this heat transfers into water-contaminated fluid, the water boils and flashes into steam vapor bubbles .
While liquid brake fluid is incompressible, steam vapor is highly compressible.
When the driver steps on the brake pedal, the hydraulic force simply compresses the steam pockets rather than displacing caliper pistons. The brake pedal falls completely to the floorboard with zero braking deceleration —a catastrophic failure condition known as vapor lock .
Professional Brake Fluid Testing Techniques
Digital Boiling Point Tester (Thermal Tester): The professional gold-standard method. A small fluid sample is drawn from the reservoir into a test vial; an electric heating element boils the fluid and displays the exact physical boiling temperature. Compare the measured boiling point with the tester, fluid, and vehicle manufacturer's service criterion; there is no universal 160°C replacement cutoff.
Optical Refractometer: Measures the refractive index of light passing through a fluid drop placed on an optical prism, providing an accurate, direct reading of water percentage.
Conductivity Pen Testers: Inexpensive handheld tools that measure electrical conductivity between two brass probe tips. While quick, conductivity pens can produce false readings: dissolved copper ions from decomposing internal copper-brazed steel brake lines increase conductivity, indicating high moisture even if the water content is low.
Professional Bleeding Procedures
Hydraulic bleeding purges entrained air bubbles and contaminated fluid from the lines. HYDRAULIC BLEEDING METHODS & SEQUENCES
- TWO-PERSON MANUAL BLEED PRESSURE BLEEDING TANK
- [Assistant Pumps & Holds] [10–15 psi Clean Air/Fluid]
- | |
- v v
- Crack Bleeder Screw 1/4 Turn Attached to Master Cyl Neck
- Fluid/Air Out via Submerged Hose Open Bleeder at Each Wheel Caliper
- |
- v
TRADITIONAL FRONT/REAR SPLIT SEQUENCE: DIAGONAL SPLIT SEQUENCE:
- Right-Rear (RR) -> Left-Rear (LR) -> Right-Rear (RR) -> Left-Front (LF) ->
- Right-Front (RF) -> Left-Front (LF) Left-Rear (LR) -> Right-Front (RF)
- (Furthest to Closest from Master Cyl) (Follow OEM Workshop Manual)
Two-Person Manual Bleeding:
An assistant pumps the brake pedal 3 times and holds firm foot pressure.
The technician cracks the bleeder screw 1/4 to 1/2 turn, allowing fluid and air to expel into a clear plastic hose submerged in a catch bottle of clean fluid.
The technician closes the bleeder screw before the assistant releases the pedal to prevent air from being sucked backward into the caliper.
Bleed in the exact manufacturer sequence. Hydraulic routing and ABS layout can make a distance-based sequence wrong.
Pressure Bleeding:
A specialized pressure pot containing fresh fluid connects to the master cylinder reservoir with an airtight adapter cap. Set pressure to the bleeder and vehicle manufacturer's limit; excessive pressure can damage or overflow the reservoir.
Clean pressurized fluid automatically keeps the reservoir filled while the technician opens bleeder screws one by one at each wheel.
Advantages: Fast, single-operator procedure that eliminates the risk of master cylinder piston over-travel into corroded bore regions.
Automated Scan-Tool ABS Bleeding:
When Required: Use the scan-tool HCU bleed when the vehicle procedure requires it, commonly after air enters or components are replaced within specified parts of the modulator circuit.
The Problem: Air bubbles become trapped behind normally closed solenoid valves, within low-pressure accumulators, and inside the high-pressure return pump passages of the HCU. Conventional bleeding may not move air from isolated passages on some designs.
Procedure: Connect an OBD-II diagnostic scan tool, navigate to ABS special functions, and execute the Automated Bleed Routine . The scan tool commands the ABS module to run its internal 12V motor, spinning the high-pressure return pump while rapidly cycling the internal inlet and outlet solenoid valves. This flushes trapped air out of internal accumulator chambers and drives it downstream into the wheel caliper circuits, where it is expelled through open bleeder screws.
Anti-Lock Braking System (ABS) Architecture & Operation
The Anti-Lock Braking System (ABS) prevents wheel lockup during emergency braking or low-traction stops, preserving directional steering control and minimizing stopping distance on most road surfaces. ABS 4-PHASE HYDRAULIC CONTROL CYCLE
- +-------------------------------------------------------------------------+
- | PHASE 1: NORMAL BRAKING (PRESSURE BUILD) |
- | Inlet Valve: OPEN (De-energized) | Outlet Valve: CLOSED (De-energized) |
- | Fluid flows unrestricted from Master Cylinder directly to Caliper. |
- +-------------------------------------------------------------------------+
- | PHASE 2: PRESSURE HOLD (IMPENDING LOCKUP DETECTED) |
- | Inlet Valve: CLOSED (Energized) | Outlet Valve: CLOSED (De-energized) |
- | Caliper fluid isolated. Clamping pressure remains constant despite pedal|
- +-------------------------------------------------------------------------+
- | PHASE 3: PRESSURE DUMP / RELEASE (WHEEL LOCKED / SKIDDING) |
- | Inlet Valve: CLOSED (Energized) | Outlet Valve: OPEN (Energized) |
- | Fluid vents from Caliper into Low-Pressure Accumulator (LPA). Wheel free|
- +-------------------------------------------------------------------------+
- | PHASE 4: PRESSURE RE-APPLY (WHEEL ACCELERATES BACK TO SPEED) |
- | Inlet Valve: OPEN (De-energized) | Outlet Valve: CLOSED (De-energized) |
- | 12V Pump scavenges LPA and re-pressurizes Caliper. Pedal kicks back! |
- +-------------------------------------------------------------------------+
- System Components & Architecture
Electronic Control Unit (ECU): A microprocessor that monitors wheel speed signals, calculates individual wheel deceleration rates and vehicle reference speed, detects impending lockup, and commands the electro-hydraulic solenoids and pump motor.
Hydraulic Control Unit (HCU / Modulator): An electro-hydraulic valve block containing:
Solenoid Valves: Typically 8 to 12 valves (one normally-open inlet valve and one normally-closed outlet valve per hydraulic channel).
Low-Pressure Accumulators (LPA): Spring-loaded diaphragm chambers that temporarily store vented high-pressure brake fluid during pressure release phases.
Electric Motor & High-Pressure Return Pump: A 12V DC motor driving a dual-opposed piston pump that scavenges fluid from the LPAs and pumps it back into the master cylinder circuits against line pressure.
Wheel Speed Sensors (WSS): Precision sensors mounted at each wheel hub reading a rotating toothed ring or magnetic encoder.
Wheel Speed Sensor Technologies: Passive VR vs. Active Hall Effect
Sensor Type Operating Principle & Signal Waveform Wiring & Electrical Characteristics Limitations & Diagnostics
Passive Variable Reluctance (VR) Permanent magnet wrapped in a fine copper coil positioned adjacent to a rotating toothed steel reluctor ring. Tooth passage alters magnetic flux, generating an analog AC sine wave . 2 wires (signal + and signal - / shield). Generates its own voltage without external power supply. Sensor resistance: 800 to 1,500 Ω . Output voltage is proportional to speed. Below 5 km/h (3 mph) , signal voltage drops below the ECU detection threshold, blinding the ABS during final stopping. Sensitive to air gap changes (0.5 to 1.5 mm).
Active Magnetoresistive / Hall Effect Solid-state semiconductor circuit reading a magnetic encoder ring embedded into the wheel bearing seal (alternating north/south poles). Produces a digital square wave . 2 or 3 wires. Requires external reference power supply (typically 5V or 12V) from the ABS ECU. Modulates circuit current (7 mA low / 14 mA high). Reads wheel speed accurately down to 0.0 km/h . Detects wheel rotation direction (forward vs reverse) for hill-start assist. Immune to air gap variations and electrical noise.
The Four Electro-Hydraulic ABS Operating Phases
During panic braking on slippery surfaces (such as wet asphalt or loose desert sand), the ABS cycles through four rapid hydraulic phases at 15 to 20 cycles per second (Hz) :
Phase 1: Normal Braking (Pressure Build Phase):
Inlet Solenoid Valve: DE-ENERGIZED ( OPEN ).
Outlet Solenoid Valve: DE-ENERGIZED ( CLOSED ).
Pump Motor: OFF.
Operation: Master cylinder pressure flows directly through the open inlet valve into the wheel caliper. Clamping force rises linearly with driver pedal effort.
Phase 2: Pressure Hold Phase:
Trigger: The ECU detects that a wheel's rate of deceleration exceeds a pre-programmed threshold (indicating impending lockup and excessive tire slip).
Inlet Solenoid Valve: ENERGIZED ( CLOSED ).
Outlet Solenoid Valve: DE-ENERGIZED ( CLOSED ).
Pump Motor: OFF.
Operation: The closed inlet valve traps fluid in the caliper bore. Clamping pressure is held constant. Even if the driver stomps harder on the brake pedal, caliper pressure cannot increase, preventing wheel lockup.
Phase 3: Pressure Dump / Release Phase:
Trigger: The wheel continues to decelerate toward zero velocity despite holding pressure.
Inlet Solenoid Valve: ENERGIZED ( CLOSED ).
Outlet Solenoid Valve: ENERGIZED ( OPEN ).
Pump Motor: ON (starts running).
Operation: Trapped fluid in the caliper vents rapidly through the open outlet valve into the Low-Pressure Accumulator (LPA). Caliper clamping force drops instantly, allowing the skidding tire to spin back up toward vehicle speed and restore frictional grip with the road surface.
Phase 4: Pressure Re-Apply Phase:
Trigger: The wheel accelerates back to matching vehicle speed.
Inlet Solenoid Valve: DE-ENERGIZED ( OPEN ).
Outlet Solenoid Valve: DE-ENERGIZED ( CLOSED ).
Pump Motor: ON (running).
Operation: The internal high-pressure return pump draws fluid from the LPA and forces it back into the master cylinder supply line, re-pressurizing the caliper to slow the wheel again. Pumping fluid back into the pressurized master cylinder line pushes the master cylinder piston backward against driver foot pressure, creating the distinct pedal pulsation (kickback) and mechanical chattering noise characteristic of ABS operation.
Integration with TCS and Electronic Stability Control (ESC / ESP)
Modern vehicles expand the ABS modulator to deliver active chassis dynamics:
Traction Control System (TCS): Prevents wheel spin during acceleration on slick surfaces. If one drive wheel loses grip, the HCU energizes high-pressure priming valves and runs the pump to apply brake pressure to the slipping wheel without driver pedal input, transferring torque across the open differential to the gripping wheel. Simultaneously signals the PCM via CAN bus to reduce throttle opening or retard ignition timing.
Electronic Stability Control (ESC / ESP): Integrates additional input sensors:
Steering Angle Sensor (SAS): Measures driver intended direction.
Yaw Rate Sensor: Measures actual vehicle rotational angular velocity around its vertical axis (deg/sec).
Lateral Acceleration Sensor: Measures cornering centrifugal G-forces.
Dynamic Correction:
Understeer (Front-End Push): Vehicle plows straight ahead during cornering. ESC automatically applies brake pressure to the inside rear wheel , inducing a corrective yaw moment that pulls the front end into the corner.
Oversteer (Rear-End Fishtail): Rear wheels break traction and slide outward. ESC automatically applies brake pressure to the outside front wheel , inducing a counter-yaw moment that prevents the vehicle from spinning out.
Master Reference: Brake Fluid Specifications & ABS Operating Phases
System Parameter FMVSS / Engineering Specification Operating State / Electrical Condition Diagnostic Verification Standard
DOT 3 Fluid Dry: ≥ 205°C (401°F); Wet: ≥ 140°C (284°F) Amber glycol ether; absorbs 1.5%–2% water/year. Use the OEM interval and approved condition test; do not apply one cutoff or calendar interval to every vehicle.
DOT 4 Fluid Dry: ≥ 230°C (446°F); Wet: ≥ 155°C (311°F) Borate ester glycol; viscosity ≤ 1,500 mm²/s. Standard fill; test with optical refractometer or boiling tester.
DOT 4 LV (Class 6) Dry: ≥ 230°C (446°F); Wet: ≥ 155°C (311°F) Low viscosity: ≤ 750 mm²/s at -40°C. Use only where Class 6 or equivalent low-viscosity fluid is specified.
DOT 5.1 Fluid Dry: ≥ 260°C (500°F); Wet: ≥ 180°C (356°F) Glycol/borate base; viscosity ≤ 900 mm²/s. Use only if it meets the exact vehicle specification; climate alone does not select the fluid.
DOT 5 (Silicone) Dry: ≥ 260°C (500°F); Wet: ≥ 180°C (356°F) Purple polydimethylsiloxane; non-hygroscopic. Not interchangeable with glycol fluid. Use only when explicitly specified; most ABS/ESC vehicles specify DOT 3, DOT 4, or DOT 5.1.
ABS Phase 1: Build Driver controlled master cylinder pressure. Inlet Valve: OPEN (de-energized); Outlet Valve: CLOSED (de-energized) Baseline resting valve state; unpowered fluid pass-through.
ABS Phase 2: Hold Trapped line pressure isolated at caliper. Inlet Valve: CLOSED (energized); Outlet Valve: CLOSED (de-energized) Line pressure holds constant; isolates caliper from increasing pedal force.
ABS Phase 3: Dump Pressure drops; fluid vents to LPA. Inlet Valve: CLOSED (energized); Outlet Valve: OPEN (energized) Caliper clamping force collapses; wheel accelerates back toward road speed.
ABS Phase 4: Re-Apply Return pump returns fluid to circuit. Inlet Valve: OPEN (de-energized); Outlet Valve: CLOSED (de-energized) 12V pump motor running; creates driver pedal pulsation / kickback.
Passive VR Sensor 800 to 1,500 Ω internal coil resistance. Analog AC sine wave; amplitude increases with speed. Inspect with lab scope for uniform sine wave peaks; verify 0.5–1.5 mm air gap.
Active Hall Sensor 5V or 12V reference power supply from ECU. Digital square wave (7 mA / 14 mA current pulses). Measure with lab scope; generates 0 to 5V clean square wave down to 0.0 km/h.