Study guide
1.1 Program Identity, Current Test Rules & Evidence Limits
Saudi Skill Verification Program - Light Vehicle Mechanic Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Assessment Overview
1.1 Program Identity, Current Test Rules & Evidence Limits 1.2 Practical Assessment Evidence, Safe Workflow & Task Preparation
2 Engine Fundamentals, Four-Stroke Cycle & Internal Components
2.1 Four-Stroke Petrol Engine Operation, Thermodynamics & Cylinder Configuration 2.2 Cylinder Block, Pistons, Rings, Connecting Rods & Crankshaft Assemblies 2.3 Cylinder Head, Valvetrain Architectures & Timing Drive Systems
3 Engine Mechanical Diagnostics & Overhaul Procedures
3.1 Compression Testing & Cylinder Leak-Down Diagnostics 3.2 Manifold Vacuum Diagnostics & Engine Oil Pressure Testing 3.3 Cylinder Head Gasket Failure Analysis, Warp Measurement & Valve Sealing
4 Engine Lubrication, Cooling & Climate Control
4.1 Engine Lubrication Principles, Oil Viscosity, Filtration & Pressure Relief 4.2 Engine Cooling System Architecture, Thermostats, Radiators & Water Pumps 4.3 Gulf Climate Cooling Performance, Electric Fan Controls & Coolant Chemistry 4.4 Automotive Air Conditioning Operation, Diagnosis & Refrigerant Service
5 Petrol Fuel Delivery & Injection Systems
5.1 Fuel Tank Assemblies, Electric Pumps, Pressure Regulation & Line Safety 5.2 Port Fuel Injection (PFI) vs. Gasoline Direct Injection (GDI) Technologies 5.3 Air Induction, Throttle Bodies, Idle Air Control & Mass Airflow / MAP Sensors
6 Ignition Systems & Engine Management
6.1 Ignition Principles, Spark Plug Heat Ranges & Secondary Voltage Patterns 6.2 Distributorless & Coil-on-Plug (COP) Ignition Architectures 6.3 Crankshaft/Camshaft Position Sensors, Timing Advance & Knock Control
7 Exhaust, Emission Control & Aftertreatment Systems
7.1 Exhaust Manifolds, Gaskets, Catalytic Converters & Thermal Efficiency 7.2 Oxygen Sensors, Air-Fuel Ratio Sensors & Fuel Trim Diagnostics 7.3 Evaporative Emission Control (EVAP) & Positive Crankcase Ventilation (PCV)
8 Automotive Electrical Fundamentals, Batteries & Charging
8.1 Electrical Fundamentals, Ohm's Law & 12V Lead-Acid Battery Diagnostics 8.2 Cranking Systems, Starter Solenoids & Voltage Drop Testing 8.3 Alternators, Rectifiers, Regulators & Charging Circuit Diagnosis
9 On-Board Diagnostics (OBD-II) & Systematic Troubleshooting
9.1 OBD-II Architecture, Standardization & Generic DTC Structure 9.2 Live PID Streaming, Freeze Frame Capture & Readiness Monitors 9.3 Systematic Diagnostic Workflow: Verify, Isolate, Repair & Validate
10 Clutches & Manual Transmissions
10.1 Friction Clutch Construction, Pressure Plates, Flywheels & Release Bearings 10.2 Hydraulic Clutch Actuation, Master/Slave Cylinders & Bleeding Procedures 10.3 Manual Gearbox Internal Operation, Synchromesh Units & Gear Selection
11 Automatic Transmissions, Drivelines & Differentials
11.1 Torque Converters, Planetary Gearsets & Automatic Transmission Fluid (ATF) 11.2 Front-Wheel-Drive Halfshafts, Constant Velocity (CV) Joints & Boots 11.3 Rear-Wheel-Drive Propeller Shafts, Universal Joints & Differential Operation
12 Hydraulic Braking Systems & ABS
12.1 Hydraulic Principles, Dual Tandem Master Cylinders & Vacuum Boosters 12.2 Disc & Drum Brake Mechanical Service, Calipers & Rotors 12.3 Brake Fluid Chemistry (DOT 3, 4, 5.1), Bleeding Methods & Anti-Lock Brakes (ABS)
13 Steering, Suspension, Wheel Alignment & Balancing
13.1 Steering Systems: Rack-and-Pinion, Hydraulic Power Steering & EPS 13.2 Suspension Architectures: MacPherson Struts, Multi-Link & Shock Absorbers 13.3 Wheel Alignment Geometry (Camber, Caster, Toe, SAI) & Tire Wear Analysis 13.4 Wheel Balancing, Runout Diagnosis & Safe Wheel Installation
14 Workshop Safety, Precision Measurement & Fastener Torquing
14.1 Personal Protective Equipment, Chemical Safety & Shop Hazard Management 14.2 Vehicle Lifting Equipment, Two-Post Lift Positioning & Hydraulic Jacks 14.3 Precision Measuring Instruments (Micrometers, Dial Gauges) & Fastener Torquing
1.1 Program Identity, Current Test Rules & Evidence Limits
Key Takeaways Explain This Topic AI
The current PACC international occupation directory lists SSCO code 9151033 as General light vehicle mechanic (ميكانيكي مركبات خفيفة عام); candidates must book the occupation that matches their work or visa record.
PACC states that assessment methodology depends on the occupation: a booking may be computer-based only or may combine computer-based and practical testing. The maximum published test duration is 120 minutes, but the booking confirmation controls the actual session.
The current published fee is USD 85 for applicants outside Saudi Arabia and SAR 702.6 for applicants inside Saudi Arabia. Fees and availability can change, so candidates should recheck PACC before paying.
PACC permits up to three attempts. A certificate is valid for two years after computer-only testing or Recognition of Prior Learning and five years after a combined computer-and-practical assessment.
PACC publishes no candidate syllabus or preparation resources for Skills Verification. This guide is an evidence-based occupational preparation aid, not an official PACC blueprint or a prediction of live questions.
Last updated: September 2026
1.1 Program Identity, Current Test Rules & Evidence Limits
The Saudi Skills Verification Program (SVP) is part of the Professional Accreditation framework overseen by the Ministry of Human Resources and Social Development and delivered through the Professional Accreditation Center (PACC). Its purpose is to verify that a professional worker has the skills needed for the occupation in which the worker will be employed. MHRSD describes Skills Verification as covering practical and theoretical assessment for covered vocational occupations.
Exact Occupation Identity
The current PACC international occupation directory lists:
- Field Current listing
- SSCO occupation code 9151033
- English occupation name General light vehicle mechanic
- Arabic occupation name ميكانيكي مركبات خفيفة عام
- Current international activation shown by PACC Pakistan, Bangladesh, Egypt, and India
The name in a local study product may be shortened to Light Vehicle Mechanic, but the booking must use the occupation shown in PACC and must match the candidate's work or visa record. Do not substitute Auto Electrician, Automotive Primary Service, or Heavy Equipment Technician merely because some tools overlap.
Important
Occupation activation and test-center availability are live booking data. Recheck the PACC search and the booking calendar before payment; a country or session shown today may change.
What PACC Publishes About the Test
PACC's current public FAQ gives rules that apply across Skills Verification occupations:
Methodology varies by occupation. A test may be computer-based only or may combine a computer-based component with a practical component.
Maximum duration: PACC states that duration differs by occupation and the maximum is 120 minutes . It does not publish a separate 90-to-120-minute practical duration for this occupation.
Languages offered at booking: Arabic, English, Hindi, Urdu, Filipino/Tagalog, Sinhala, Tamil, Bengali, and Nepali. Availability can depend on the booked occupation and session.
Identity documents: Bring the original national identity card, residency card, or passport, as applicable, plus the test ticket.
Arrival: PACC instructs candidates to reach the test center 30 minutes before the appointment.
Attempts: A candidate may attempt the assessment up to three times , paying for each attempt.
Combined retake rule: PACC states that if a candidate passes the practical component but fails the computer component, the complete assessment is repeated because the components are complementary.
Cancellation or rescheduling: The public FAQ allows one cancellation or reschedule at least 72 hours before the appointment. A no-show is treated as a withdrawal, and the payment is not refunded.
PACC does not publish a question count, domain weights, a numeric cut score, station sequence, or the scoring rubric for General light vehicle mechanic. Do not invent any of those values.
Current Fees and Certificate Validity
The public PACC FAQ reviewed on 24 September 2026 states:
- Candidate route Published fee
- Outside Saudi Arabia USD 85
- Inside Saudi Arabia SAR 702.6
- Recognition of Prior Learning (RPL) USD 85
Payment is made by Visa or MasterCard after the candidate selects the methodology and occupation. PACC says paid amounts are non-refundable, except that a technical payment failure or a center cancellation may create account credit under the platform rules. Treat every fee as time-sensitive and verify the checkout amount before paying.
Certificate validity depends on the assessment methodology:
Computer-based only: two years.
Computer-based plus practical: five years.
Recognition of Prior Learning: two years.
Evidence-Based Preparation Blueprint
PACC explicitly says it provides no review resources and that the assessment is based on the occupation registered in the work permit. Therefore, this guide does not label its chapter plan as an official PACC syllabus. Its preparation blueprint is derived from three independent evidence layers:
Current PACC identity and rules: exact occupation code/name, current program logistics, and live availability.
Current Saudi TVTC automotive training scope: fuel systems, power transmission, engine diagnosis and repair, brakes, steering and suspension, vehicle testing, electrical/electronic systems, emissions, workshop safety, and fault diagnosis.
Saudi-partner practical evidence: NAVTTC materials for the Takamol automotive trade identify practical tasks and current test-center equipment. Published tasks include front brake-pad replacement, shock-absorber replacement, valve-cover-gasket replacement, wheel balancing, engine-oil service, parking-brake adjustment, drive-belt replacement, and thermostat replacement. The current Auto Mechanic equipment list also includes scan tools, electrical testers, brake tools, alignment and balancing equipment, transmission tools, cooling equipment, and A/C recovery/service equipment.
These sources justify broad occupational preparation, but they do not prove that every candidate receives every listed task. The live booking, center instructions, and task sheet control on test day.
Candidate Action Plan
Search PACC for occupation 9151033 General light vehicle mechanic and confirm it matches the employment record.
Confirm the country, center, methodology, language, date, duration, documents, and checkout fee shown in the booking.
Prepare for both theory and hands-on work when the booking includes both components.
Practice safe, specification-led procedures instead of memorizing unofficial answer banks.
Use OEM service information for torque, fluid, clearance, pressure, refrigerant, and alignment specifications; generic values in study examples are not vehicle specifications.
Recheck the PACC FAQ shortly before the appointment for rule or fee changes.
- Official Checkpoints
- PACC program, occupation search, certificate verification, and FAQ: https://pacc.sa/
- PACC international booking portal: https://svp-international.pacc.sa/
- MHRSD Skills and Training information: https://www.hrsd.gov.sa/en/care-about-you/skillsandtrain
- Saudi-partner Takamol information and current trade tool lists: https://navttc.gov.pk/takamol/