Study guide
9.1 OBD-II Architecture, Standardization & Generic DTC Structure
Saudi Skill Verification Program - Light Vehicle Mechanic Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Assessment Overview
1.1 Program Identity, Current Test Rules & Evidence Limits 1.2 Practical Assessment Evidence, Safe Workflow & Task Preparation
2 Engine Fundamentals, Four-Stroke Cycle & Internal Components
2.1 Four-Stroke Petrol Engine Operation, Thermodynamics & Cylinder Configuration 2.2 Cylinder Block, Pistons, Rings, Connecting Rods & Crankshaft Assemblies 2.3 Cylinder Head, Valvetrain Architectures & Timing Drive Systems
3 Engine Mechanical Diagnostics & Overhaul Procedures
3.1 Compression Testing & Cylinder Leak-Down Diagnostics 3.2 Manifold Vacuum Diagnostics & Engine Oil Pressure Testing 3.3 Cylinder Head Gasket Failure Analysis, Warp Measurement & Valve Sealing
4 Engine Lubrication, Cooling & Climate Control
4.1 Engine Lubrication Principles, Oil Viscosity, Filtration & Pressure Relief 4.2 Engine Cooling System Architecture, Thermostats, Radiators & Water Pumps 4.3 Gulf Climate Cooling Performance, Electric Fan Controls & Coolant Chemistry 4.4 Automotive Air Conditioning Operation, Diagnosis & Refrigerant Service
5 Petrol Fuel Delivery & Injection Systems
5.1 Fuel Tank Assemblies, Electric Pumps, Pressure Regulation & Line Safety 5.2 Port Fuel Injection (PFI) vs. Gasoline Direct Injection (GDI) Technologies 5.3 Air Induction, Throttle Bodies, Idle Air Control & Mass Airflow / MAP Sensors
6 Ignition Systems & Engine Management
6.1 Ignition Principles, Spark Plug Heat Ranges & Secondary Voltage Patterns 6.2 Distributorless & Coil-on-Plug (COP) Ignition Architectures 6.3 Crankshaft/Camshaft Position Sensors, Timing Advance & Knock Control
7 Exhaust, Emission Control & Aftertreatment Systems
7.1 Exhaust Manifolds, Gaskets, Catalytic Converters & Thermal Efficiency 7.2 Oxygen Sensors, Air-Fuel Ratio Sensors & Fuel Trim Diagnostics 7.3 Evaporative Emission Control (EVAP) & Positive Crankcase Ventilation (PCV)
8 Automotive Electrical Fundamentals, Batteries & Charging
8.1 Electrical Fundamentals, Ohm's Law & 12V Lead-Acid Battery Diagnostics 8.2 Cranking Systems, Starter Solenoids & Voltage Drop Testing 8.3 Alternators, Rectifiers, Regulators & Charging Circuit Diagnosis
9 On-Board Diagnostics (OBD-II) & Systematic Troubleshooting
9.1 OBD-II Architecture, Standardization & Generic DTC Structure 9.2 Live PID Streaming, Freeze Frame Capture & Readiness Monitors 9.3 Systematic Diagnostic Workflow: Verify, Isolate, Repair & Validate
10 Clutches & Manual Transmissions
10.1 Friction Clutch Construction, Pressure Plates, Flywheels & Release Bearings 10.2 Hydraulic Clutch Actuation, Master/Slave Cylinders & Bleeding Procedures 10.3 Manual Gearbox Internal Operation, Synchromesh Units & Gear Selection
11 Automatic Transmissions, Drivelines & Differentials
11.1 Torque Converters, Planetary Gearsets & Automatic Transmission Fluid (ATF) 11.2 Front-Wheel-Drive Halfshafts, Constant Velocity (CV) Joints & Boots 11.3 Rear-Wheel-Drive Propeller Shafts, Universal Joints & Differential Operation
12 Hydraulic Braking Systems & ABS
12.1 Hydraulic Principles, Dual Tandem Master Cylinders & Vacuum Boosters 12.2 Disc & Drum Brake Mechanical Service, Calipers & Rotors 12.3 Brake Fluid Chemistry (DOT 3, 4, 5.1), Bleeding Methods & Anti-Lock Brakes (ABS)
13 Steering, Suspension, Wheel Alignment & Balancing
13.1 Steering Systems: Rack-and-Pinion, Hydraulic Power Steering & EPS 13.2 Suspension Architectures: MacPherson Struts, Multi-Link & Shock Absorbers 13.3 Wheel Alignment Geometry (Camber, Caster, Toe, SAI) & Tire Wear Analysis 13.4 Wheel Balancing, Runout Diagnosis & Safe Wheel Installation
14 Workshop Safety, Precision Measurement & Fastener Torquing
14.1 Personal Protective Equipment, Chemical Safety & Shop Hazard Management 14.2 Vehicle Lifting Equipment, Two-Post Lift Positioning & Hydraulic Jacks 14.3 Precision Measuring Instruments (Micrometers, Dial Gauges) & Fastener Torquing
9.1 OBD-II Architecture, Standardization & Generic DTC Structure
Key Takeaways Explain This Topic AI
The standardized SAE J1962 16-pin Data Link Connector (DLC) mandates uniform vehicle interface pin assignments, notably Pin 4 (Chassis Ground), Pin 5 (Signal Ground), Pin 6 (CAN High, 2.5V recessive / 3.5V dominant), Pin 14 (CAN Low, 2.5V recessive / 1.5V dominant with 60 Ω total termination resistance across pins 6 and 14), and Pin 16 (Permanent Battery +12V power).
SAE J2012 Diagnostic Trouble Codes (DTCs) follow a standardized 5-character alphanumeric taxonomy: the 1st character defines the system (P, B, C, U), the 2nd character indicates whether the code is SAE generic (0, 2) or OEM-specific (1, 3), the 3rd digit identifies the powertrain subsystem (1–9), and the 4th/5th digits pinpoint the specific component fault (00–99).
The Malfunction Indicator Lamp (MIL) responds dynamically to fault severity: Type A faults (catalyst-damaging misfires or critical emission failures) illuminate the MIL immediately on the 1st drive cycle and flash rapidly during active misfires to avert ceramic substrate melting, whereas Type B faults require two consecutive trips with pending confirmation before commanding solid MIL illumination.
Clearing diagnostic memory via scan tool Mode $04 erases confirmed DTCs, pending DTCs, and Freeze Frame snapshots, but simultaneously resets all continuous and non-continuous readiness monitors to 'Not Ready,' which will cause the vehicle to fail statutory inspection.
The Powertrain Control Module (PCM) operates autonomous self-clearing algorithms: if a detected fault condition ceases and does not recur across three consecutive conforming drive cycles, the MIL extinguishes; the historical DTC is completely purged from non-volatile memory after forty consecutive warm-up cycles without fault recurrence.
Last updated: September 2026
9.1 OBD-II Architecture, Standardization & Generic DTC Structure
Modern automotive electronics rely on On-Board Diagnostics Generation Two (OBD-II) as the universal electronic backbone for powertrain fault detection, emission monitoring, and vehicle health assessment. Mandated across North America in 1996, implemented across Europe as EOBD in 2001, and strictly enforced across the Gulf Cooperation Council (GCC) through Saudi Standards, Metrology and Quality Organization (SASO) and GSO vehicle regulations, OBD-II transformed automotive diagnostics from proprietary, manufacturer-locked service equipment to an interoperable, standardized diagnostic framework accessible by any compliant scan tool.
For automotive technicians preparing for the Saudi Skill Verification Program (SVP) , mastering the physical, electrical, and logical architecture of OBD-II is essential. Diagnosing complex drivability symptoms in modern passenger vehicles requires a deep understanding of Data Link Connector (DLC) pin configurations, communication bus voltages, alphanumeric trouble code taxonomy, and engine control unit (ECU) fault confirmation protocols.
Regulatory Background & Objectives of OBD-II
Prior to OBD-II standardization, early vehicle computerized systems (OBD-I) featured disjointed, proprietary diagnostic connectors, non-standardized baud rates, and manufacturer-specific diagnostic trouble code schemes. Technicians required dozens of distinct adapter cables and expensive OEM diagnostic consoles to extract basic engine fault codes. Furthermore, OBD-I systems lacked standardized component monitoring; they primarily alerted the driver to catastrophic electrical circuit opens or shorts rather than gradual component degradation.
OBD-II solved these limitations by introducing a universally regulated platform designed to achieve four core objectives:
Standardized Physical Interface: Mandating a universal 16-pin connector accessible from the driver's seat without tools.
Standardized Electrical Protocols: Unifying in-vehicle digital communication under defined SAE and ISO network standards, culminating in high-speed Controller Area Network (CAN) bus protocols.
Standardized Diagnostic Trouble Codes (SAE J2012): Establishing a uniform alphanumeric format across all automotive manufacturers so that core emission and powertrain codes carry identical technical definitions regardless of vehicle make.
Comprehensive System and Component Monitoring: Requiring the engine control module to evaluate system performance and component degradation (e.g., catalytic converter efficiency, evaporative emission leak detection, oxygen sensor response latency, cylinder misfires) long before tailpipe emissions reach hazardous thresholds.
SAE J1962 16-Pin Data Link Connector (DLC) Architecture
The physical gateway between the vehicle's internal electronic control networks and the diagnostic technician is the SAE J1962 Data Link Connector (DLC) . By statutory mandate, the DLC must be located within the passenger compartment, readily accessible from the driver's seat, typically situated under the instrument panel beneath the steering column or within 300 mm (12 inches) of the vehicle centerline, requiring no tools for technician access.
Two physical variants of the J1962 connector exist:
Type A: Standard connector used in 12V passenger vehicles, featuring an uninterrupted center alignment tab.
Type B: Heavy-duty and commercial connector rated for 24V vehicle architectures, featuring an interrupted (split) center alignment tab to prevent technicians from accidentally plugging 12V diagnostic interfaces into 24V vehicle networks. +-----------------------------------------+
- \ 1 2 3 4 5 6 7 8 /
- \ /
- \ 9 10 11 12 13 14 15 16 /
- +-----------------------------------+
- Standardized Pin Assignments & Electrical Specifications
While automotive manufacturers are permitted to assign proprietary functions to specific vendor-discretionary terminals, the primary ground, power, and standardized communication terminals are strictly codified:
Pin 4 — Chassis Ground: Provides a direct, low-resistance return path to the vehicle chassis frame and sheet metal. Voltage drop between Pin 4 and the battery negative terminal under full scan tool operating current must not exceed 0.100V (100 mV).
Pin 5 — Signal Ground: Provides an isolated, clean sensor ground referenced directly to the internal ground plane of the Powertrain Control Module (PCM). This dedicated terminal prevents high-current electrical noise generated by alternators, ignition coils, and radiator cooling fans from corrupting digital serial data.
Pin 6 — CAN High (CAN-H): Operates under ISO 15765-4 (High-Speed Controller Area Network) at 500 kbps (or 250 kbps on select platforms). In its recessive (quiescent) state, CAN-H rests at nominal 2.50V DC . During active communication (dominant state), the bus transceiver drives CAN-H up to nominal 3.50V DC .
Pin 14 — CAN Low (CAN-L): Operates as the differential complement to Pin 6. In its recessive state, CAN-L rests at nominal 2.50V DC . During active communication (dominant state), the bus transceiver pulls CAN-L down to nominal 1.50V DC . The resulting differential voltage across Pins 6 and 14 in dominant state is 2.0V DC (3.5V − 1.5V = 2.0V), providing exceptional immunity to electromagnetic interference (EMI).
CAN Bus Termination Resistance (Pins 6 & 14): The high-speed CAN network relies on two 120 Ω terminating resistors wired in parallel at opposite ends of the physical bus (typically housed internally within the PCM and the instrument cluster or central gateway). With the vehicle battery disconnected, a digital multimeter set to ohms connected across Pin 6 and Pin 14 must measure exactly 60 Ω (120 Ω in parallel with 120 Ω = 60 Ω). A measurement of 120 Ω indicates that one terminating resistor or its respective circuit branch is open, whereas 0 Ω indicates a direct short between the data lines.
Pin 16 — Constant Battery Power (+12V): Delivers unswitched positive battery voltage directly from a dedicated fuse in the vehicle fuse block (typically protected by a 7.5A, 10A, or 15A fuse). Pin 16 powers diagnostic scan tools and vehicle communication interfaces (VCIs) without requiring separate power cables.
Pin 7 — ISO 9141-2 / ISO 14230-4 K-Line: Bi-directional asynchronous serial communication line operating at 10.4 kbps, pulling up to battery voltage and pulling down to ground to transmit diagnostic data on legacy systems.
Pin 15 — ISO 9141-2 / ISO 14230-4 L-Line: Unidirectional initialization line used during legacy protocol wake-up sequences.
Pin 2 — SAE J1850 Pulse Width Modulation (PWM) / Variable Pulse Width (VPW) Bus (+): Legacy bus line utilized predominantly by Ford (PWM, differential with Pin 10) and General Motors (VPW, single-wire 0–7V pulses).
Pin 10 — SAE J1850 PWM Bus (−): Complementary differential data line utilized on Ford J1850 PWM architectures.
Vendor Discretionary Pins (1, 3, 8, 9, 11, 12, 13): Utilized by manufacturers for proprietary diagnostics, secondary body CAN networks, LIN bus interrogation, flash reprogramming power feeds, or security immobilizer handshakes.
Note
Diagnostic Check at the DLC Before connecting an advanced diagnostic scan tool to an unfamiliar vehicle, technicians must perform a rapid pre-check with a Digital Multimeter (DMM) or DLC breakout box: verify battery voltage between Pin 16 and Pin 4 (> 12.0V), verify ground integrity on Pin 4 and Pin 5 (< 0.1V drop to battery negative), and verify bus termination resistance across Pins 6 and 14 (60 Ω with battery negative disconnected). Connecting expensive scan tools to a DLC with a shorted power pin or high voltage on data lines can destroy the scan tool interface.
SAE J2012 Standardized Alphanumeric DTC Structure
When an electronic control module detects a sensor reading outside calibrated limits, an irrational physical behavior, or an open/shorted actuator circuit, it stores a Diagnostic Trouble Code (DTC) . Under SAE J2012 and ISO 15031-6 , all standard fault codes consist of a five-character alphanumeric string structured into four distinct logical positions. +------- Position 1: System Category (P, B, C, U)
- | +--- Position 2: Code Type (0, 1, 2, 3)
- | | +--- Position 3: Powertrain Subsystem (1 - 9)
- | | | +--- Positions 4 & 5: Specific Fault Digits (00 - 99)
- | | | |
- [P] [0] [3] [02]
- 1. First Character: Vehicle System Category
The opening alpha character identifies the broad automotive functional system responsible for the fault condition:
P — Powertrain: Encompasses all engine components, fuel induction, ignition, emissions control, automatic transmission, transfer case, and hybrid/electric drive modules.
B — Body: Encompasses passenger compartment systems, including climate control (HVAC), supplemental restraint systems (airbags/seatbelt pretensioners), power windows, interior/exterior lighting, central locking, and instrumentation.
C — Chassis: Encompasses running gear, chassis dynamics, and mechanical stability systems, including Anti-lock Braking Systems (ABS), Electronic Stability Program (ESP/TCS), steering angle sensors, electric power steering (EPS), and active suspension.
U — Network & Communication: Encompasses inter-module data sharing, Controller Area Network (CAN) bus communication wiring, lost communication with specific control modules (e.g., U0100 — Lost Communication with ECM/PCM), data bus parity errors, and invalid software handshake messaging.
2. Second Character: Code Type (Standardization Level)
The second character distinguishes standardized, universally defined fault codes from proprietary OEM codes:
0 — SAE Generic Standard: Mandated by SAE and international regulatory bodies. The code definition is universally identical across all vehicle makes and models (e.g., P0102 always defines a low-voltage condition in the Mass Air Flow sensor circuit, whether on a Toyota, Ford, Hyundai, or Mercedes-Benz).
1 — Manufacturer-Specific Enhanced: Reserved for proprietary manufacturer definitions. The vehicle manufacturer assigns the specific component and failure criteria (e.g., P1135 or P1443 may have completely different definitions depending on whether the vehicle is manufactured by Nissan, BMW, or General Motors).
2 — SAE Generic Standard (Expanded): Mandated generic code expanding beyond the initial P0xxx range to accommodate advanced systems (e.g., P2096 — Post Catalyst Fuel Trim System Too Lean Bank 1).
3 — Generic or Manufacturer Reserved: Characters P30xx through P33xx are reserved generic codes; characters P34xx through P39xx are designated for manufacturer-specific powertrain systems, including cylinder deactivation and advanced hybrid battery management.
3. Third Character: Powertrain Subsystem Classification
For powertrain codes (P-codes), the third character isolates the precise functional mechanical or electrical subsystem experiencing the fault:
1 — Fuel and Air Metering: Mass Air Flow (MAF), Manifold Absolute Pressure (MAP), Intake Air Temperature (IAT), throttle position sensors, and fuel trim calculations (e.g., P0171 — System Too Lean Bank 1).
2 — Fuel and Air Metering (Injector Subsystem): Direct/port fuel injector circuits, injector driver stages, fuel rail pressure sensors, and injection timing faults (e.g., P0201 — Injector Circuit/Open Cylinder 1).
3 — Ignition System or Engine Misfire: Crankshaft/camshaft position sensors, ignition coils, spark plug firing voltage breakdown, and detected cylinder misfire events (e.g., P0300 — Random/Multiple Cylinder Misfire Detected; P0303 — Cylinder 3 Misfire Detected).
4 — Auxiliary Emission Controls: Catalytic converter efficiency, evaporative emission (EVAP) purge/vent controls, secondary air injection (AIR) pumps, and Exhaust Gas Recirculation (EGR) valves (e.g., P0420 — Catalyst System Efficiency Below Threshold Bank 1; P0442 — EVAP System Small Leak Detected).
5 — Vehicle Speed Control & Idle Regulation: Idle Air Control (IAC) valves, electronic drive-by-wire throttle actuators, cruise control modules, and vehicle speed sensor (VSS) circuits.
6 — Computer Internal & Output Circuits: PCM microprocessor processing errors, internal Analog-to-Digital (A/D) converter failures, 5V reference supply circuit collapse, and driver transistor output circuits (e.g., P0606 — ECM/PCM Processor Fault).
7, 8, 9 — Transmission & Transaxle Systems: Transmission fluid pressure sensors, torque converter lockup clutch solenoids, shift solenoids, input/output shaft speed sensors, and gear ratio mismatch errors (e.g., P0730 — Incorrect Gear Ratio; P0741 — Torque Converter Clutch Circuit Performance/Stuck Off).
4. Fourth & Fifth Characters: Specific Component Fault Identification
The final two numeric digits (ranging from 00 to 99) isolate the specific component, circuit line, or functional performance failure (e.g., distinguishing between an open circuit, a short-to-ground, a short-to-power, or a performance/rationality range limit).
Malfunction Indicator Lamp (MIL) Operational Logic
The Malfunction Indicator Lamp (MIL) —commonly known as the Check Engine Light or Service Engine Soon indicator—serves as the primary visual warning interface notifying the vehicle operator of an emission or powertrain electronic malfunction. The engine management computer does not illuminate the MIL indiscriminately; it follows strict multi-trip validation logic defined by SAE J1979: +-------------------------+
- | Driving Cycle Initiated |
- +------------+------------+
- |
- +------------v------------+
- | Monitor Runs & Detects |
- | Emission Fault Event |
- +------------+------------+
- |
- +----------------------+----------------------+
- | |
- [Type A Fault Detected] [Type B Fault Detected]
- | |
- +---------v---------+ +---------v---------+
- | Cat-Damaging | | First Trip Fail: |
- | Misfire Active? | | Log Pending DTC |
- +----+---------+----+ | (Mode $07) |
- | | | MIL Remains OFF |
- YES | | NO +---------+---------+
- +---------------v---+ +---v---------------+ |
- | FLASH MIL WARNING | | Solid MIL ON | +---------v---------+
- | Strategy Varies | | Store Hard DTC | | 2nd Consec. Trip: |
- | Store FreezeFrame | | Store FreezeFrame | | Fault Reappears? |
- +-------------------+ +-------------------+ +----+---------+----+
- | |
- YES | | NO
- +-------------v---+ +---v-------------+
- | Solid MIL ON | | Pending DTC |
- | Store Hard DTC | | Cleared; |
- | Mode $03 / $02 | | MIL Stays OFF |
- +-----------------+ +-----------------+
- Fault Classification: Type A vs. Type B Faults
Type A Faults (Single-Trip Immediate Severe Faults):
Represent severe emissions failures or catalyst-damaging engine misfires .
Operational Action: Illuminates the MIL immediately during the first driving cycle in which the failure occurs. The PCM simultaneously logs a confirmed DTC in Mode $03 and captures a comprehensive Freeze Frame record in Mode $02.
Flashing MIL Operation: If the controller detects a misfire severe enough to threaten catalyst damage, it flashes the MIL as an urgent warning. Detection threshold, flash cadence, and protective actions such as torque reduction or cylinder fuel cut depend on the vehicle calibration.
Type B Faults (Two-Trip Confirmation Faults):
Represent the majority of emission-related faults (e.g., slow heated oxygen sensor switching, minor evaporative system vapor leaks, or marginal catalytic converter efficiency).
First Trip (Maturing Stage): When the diagnostic monitor detects a fault during the first driving cycle, the MIL remains unlit . The PCM logs the code in volatile memory as a Pending Diagnostic Trouble Code (Mode $07) . No Freeze Frame is permanently committed unless specified by manufacturer strategy.
Second Trip (Confirmation Stage): If the vehicle is driven again under similar operating conditions (engine speed, load, and coolant temperature within calibrated windows) and the monitor executes and detects the fault a second consecutive time, the fault is confirmed. The PCM illuminates the MIL solid , converts the code into a confirmed Stored DTC (Mode $03) , and locks a Freeze Frame (Mode $02) snapshot into non-volatile memory.
If the fault does not recur during the second driving cycle, the pending code is automatically dropped from Mode $07.
Important
Flashing MIL Requires Prompt Safe Action A flashing MIL during a misfire warns of catalyst-damage risk. Reduce load, follow the owner's manual, and stop safely if the engine is running poorly or the warning persists. Continuing operation can overheat the catalyst, but exact risk and controller response depend on the fault and vehicle.
DTC Clearing & Automated Memory Erasure Criteria
Diagnostic memory can be cleared through technician intervention or autonomous PCM self-clearing algorithms:
Manual Scan Tool Clearing (Mode $04): When a technician executes a Mode $04 clear command via scan tool, the PCM erases all confirmed stored DTCs (Mode $03), pending DTCs (Mode $07), Freeze Frame data (Mode $02), and oxygen sensor test logs. Mode $04 resets applicable supported readiness monitor completion flags to 'Not Ready.' Technicians must never clear codes immediately before a vehicle undergoes mandatory inspection.
Autonomous MIL Extinction (3-Trip Self-Clearing): If a confirmed Type B fault ceases to exist and does not recur during three consecutive conforming driving cycles under matching operating conditions, the PCM automatically turns off the MIL. However, the DTC remains archived in historical memory.
Autonomous DTC Memory Deletion (40 Warm-Up Cycles): The historical DTC and its associated Freeze Frame record remain stored in the PCM non-volatile memory until the vehicle completes forty (40) consecutive engine warm-up cycles without the fault recurring. Under SAE J1979 regulations, an engine warm-up cycle is defined as a driving event where engine coolant temperature rises by at least 22°C (40°F) from engine startup and achieves a minimum operating temperature of 70°C (160°F) .
Summary Reference: OBD-II DTC Architecture & Subsystem Categories
- Position Character Code Technical Classification Systems & Components Covered
- 1st Character P Powertrain System Internal combustion engine, transmission, hybrid drive, fuel, emissions
- B Body System Airbags, HVAC, central locking, power windows, exterior lighting
- C Chassis System Anti-lock brakes (ABS), traction control (ESP), steering, suspension
- U Network Communication CAN bus lines, inter-module data sharing, lost communication (e.g., U0100)
- 2nd Character 0 SAE Generic Standard Globally standardized fault definitions mandated by SAE J2012 / ISO 15031
- 1 Manufacturer Enhanced Proprietary codes unique to specific vehicle manufacturers (OEM specific)
- 2 SAE Generic (Expanded) Additional standardized generic definitions (e.g., advanced fuel trims)
- 3 Generic / OEM Reserved P30xx–P33xx generic; P34xx–P39xx manufacturer-specific powertrain
- 3rd Character 1 Fuel & Air Metering MAF, MAP, IAT, throttle bodies, intake vacuum, fuel trim balance
- (Powertrain) 2 Fuel Injector Circuit Direct/port fuel injectors, injector wiring, driver stages, rail pressure
- 3 Ignition System & Misfire Crank/cam sensors, ignition coils, spark plugs, cylinder misfire detection
- 4 Auxiliary Emission Controls Catalytic converters, EVAP purge/vent system, secondary air injection, EGR
- 5 Speed Control & Idle Idle Air Control (IAC), drive-by-wire throttle servos, cruise control
- 6 Computer Internal / Outputs PCM microprocessor, 5V sensor reference bus, memory checksums, output drivers
- 7 Transmission Systems Shift solenoids, pressure control solenoids, torque converter clutches (TCC)
- 8 Transmission Systems Electronic transmission range, gear ratio calculations, transaxle controllers
- 9 Transmission / Propulsion Advanced electronic transfer cases, all-wheel-drive coupling, alternative fuel
4th & 5th Digits 00 – 99 Specific Fault Specifics Specific circuit open, short to ground, short to battery, or rational performance