Study guide

12.5 Chemical Feed Equipment & Calibration

South Carolina Water/Wastewater Operator Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: South Carolina Regulations & Licensing Framework

1.1 SC Environmental Certification Board & Chapter 51 Regulations 1.2 Certification Levels & Experience Requirements 1.3 Facility Classifications & Operator-in-Charge Duties 1.4 Exam Logistics, Scoring & Study Resources

2 Chapter 2: Source Water Characteristics

2.1 Raw Water Sources & Pretreatment 2.2 Groundwater Sources, Wells & GWUDI Determinations 2.3 Watershed Protection & Source Water Contaminants

3 Chapter 3: Water Treatment: Coagulation, Flocculation & Sedimentation

3.1 Coagulation & Flocculation Process Control 3.2 Sedimentation Basins & Clarification

4 Chapter 4: Water Treatment: Filtration

4.1 Granular Media & Membrane Filtration 4.2 Filter Operation, Backwash & Troubleshooting

5 Chapter 5: Water Treatment: Disinfection & Chemical Conditioning

5.1 Chlorination & Chemical Disinfection 5.2 CT Calculations & Disinfection Byproducts Compliance 5.3 Chloramines, Chlorine Dioxide, Ozone & UV 5.4 Corrosion Control & the Lead and Copper Rule 5.5 Fluoridation & Water Softening 5.6 Iron, Manganese, Taste & Odor Control

6 Chapter 6: Water Distribution Systems

6.1 Water Distribution Network Operations & Maintenance 6.2 Cross-Connection Control & Backflow Prevention 6.3 Distribution Hydraulics & Pressure Management 6.4 Pipes, Valves, Hydrants & Appurtenances 6.5 Storage Tanks & Reservoirs 6.6 Water Quality in Distribution: Flushing & Residual Management 6.7 Main Disinfection, Breaks & Repair

7 Chapter 7: Wastewater Collection & Preliminary Treatment

7.1 Wastewater Collection & Preliminary Operations 7.2 Sanitary Sewer Collection System Maintenance 7.3 Lift Station Pumps, Controls & Hydraulics

8 Chapter 8: Wastewater Treatment: Primary & Secondary

8.1 Wastewater Characteristics & Plant Loadings 8.2 Primary Sedimentation & Clarifier Operations 8.3 Activated Sludge Process Control & Operations 8.4 Activated Sludge Troubleshooting 8.5 Aeration Systems & Dissolved Oxygen Control 8.6 Fixed-Film & Lagoon Treatment Systems 8.7 Biological Nutrient Removal & Tertiary Treatment

9 Chapter 9: Wastewater Disinfection, Effluent & Industrial Treatment

9.1 Wastewater Disinfection & Dechlorination 9.2 Effluent Disposal, Reuse & Land Application 9.3 Physical/Chemical Industrial Wastewater Treatment 9.4 Industrial Pretreatment Programs

10 Chapter 10: Solids, Biosolids & Regulatory Permitting

10.1 Sludge Thickening, Digestion & Dewatering 10.2 Biosolids Stabilization & Part 503 Land Application 10.3 Clean Water Act & NPDES Permit Compliance 10.4 Safe Drinking Water Act Compliance & Public Notification

11 Chapter 11: Laboratory Analysis & Quality Control

11.1 Sampling, Preservation & Chain of Custody 11.2 Physical & Chemical Water Quality Analysis 11.3 Wastewater Process Testing & Analytical Methods 11.4 Microbiological Testing & Quality Assurance 11.5 Data Validation, Reporting & Laboratory Certification

12 Chapter 12: Equipment Operation & Maintenance

12.1 Pumps: Types, Curves & Cavitation 12.2 Motors, Drives & Electrical Fundamentals 12.3 Bearings, Seals, Couplings & Lubrication 12.4 Flow Measurement & Process Instrumentation 12.5 Chemical Feed Equipment & Calibration 12.6 SCADA, Controls & Preventive Maintenance Programs

13 Chapter 13: Safety, Security & Administrative Procedures

13.1 Confined Space Entry & Atmospheric Hazards 13.2 Chlorine Gas Safety & Emergency Response 13.3 Lockout/Tagout, PPE, Hazard Communication & Excavation 13.4 Security, Vulnerability Assessment & Emergency Response Planning 13.5 Recordkeeping, Reporting & Administrative Duties

14 Chapter 14: Process Calculations & Hydraulic Math

14.1 Basic Water & Wastewater Math Fundamentals 14.2 Chemical Feed Rate & Dosage Calculations 14.3 Detention Time & Volumetric Flow Calculations 14.4 Removal Efficiency & Process Loading Rates 14.5 Pump Hydraulics & Horsepower Calculations 14.6 Activated Sludge Process Control Math

12.5 Chemical Feed Equipment & Calibration

Key Takeaways Explain This Topic AI

Metering pump output is adjusted by changing stroke length, stroke frequency, or both, and must be verified rather than trusted to the dial setting.

A drawdown calibration cylinder is the standard method for verifying liquid chemical feed rate in the field.

Gravimetric dry feeders weigh the chemical and are more accurate than volumetric feeders, which measure by volume and are affected by bulk density changes.

Chemical feed lines must be clearly labeled and chemicals must never be stored where an incompatible spill could mix, particularly hypochlorite and acid.

Feeders must be interlocked with flow so chemical cannot be fed when water is not moving.

Last updated: August 2026

12.5 Chemical Feed Equipment & Calibration

Chapter 14 teaches you to calculate a dose. This section is about whether the plant actually delivers it. The gap between the two is where most chemical-related compliance problems live.

  • 1. Liquid Chemical Feed
  • Metering pump types
  • Type Character
  • Diaphragm (mechanical or hydraulic) Most common. A reciprocating diaphragm displaces a fixed volume per stroke

Peristaltic (hose/tube) A roller squeezes a flexible tube. Liquid touches only the tube , so it handles aggressive chemicals and slurries well. Tube is a scheduled wear item

  • Progressive cavity Steady, non-pulsing flow. Excellent for polymer , which shears in other pump types
  • Piston / plunger High pressure and high accuracy; less tolerant of solids
  • How output is adjusted

Adjustment Effect

Stroke length Volume displaced per stroke. Generally least accurate below about 20–30% of full stroke — do not run a pump way down on stroke length

  • Stroke frequency (speed) Strokes per minute. Generally more linear than stroke length
  • Both Set stroke length for the coarse range and vary frequency for control
  • External signal 4–20 mA or pulse input, often flow-paced so dose stays constant as flow changes
  • Essential accessories — and why each exists
  • Item Purpose
  • Calibration (drawdown) cylinder Direct volumetric verification of actual output
  • Back pressure valve Prevents siphoning through the pump when discharge pressure is lower than suction

Pressure relief valve Mandatory — a metering pump is a positive displacement machine (Section 12.1) and must never see a closed discharge

  • Pulsation dampener Smooths pulsating flow so downstream instruments and injection behave
  • Foot valve and strainer Keeps the suction line primed and clean

Injection quill with check valve Delivers chemical into the center of the flow stream and prevents backflow into the feed line

Flow switch interlock Stops the feeder when water is not flowing

The interlock rule: a chemical feeder must never operate when the process flow has stopped. Without an interlock, a stopped high-service pump plus a running fluoride or hypochlorite feeder delivers a concentrated slug into the first water that moves. This is a recurring cause of real overfeed incidents.

Drawdown calibration — the standard field procedure

Open the valve so the pump draws from the graduated calibration cylinder instead of the bulk tank.

Note the starting level and start a stopwatch.

Run for a measured interval — typically 5 to 15 minutes so the volume is large enough to measure precisely.

Record the volume drawn down.

Calculate: Feed rate (mL/min) = Volume drawn (mL) Time (min) \text{Feed rate (mL/min)} = \frac{\text{Volume drawn (mL)}}{\text{Time (min)}} Feed rate (mL/min) = Time (min) Volume drawn (mL) ​ gal/day = mL/min × 1,440 3,785 \text{gal/day} = \frac{\text{mL/min} \times 1{,}440}{3{,}785} gal/day = 3 , 785 mL/min × 1 , 440 ​ lb/day of chemical = gal/day × 8.34 × Specific Gravity × Purity \text{lb/day of chemical} = \text{gal/day} \times 8.34 \times \text{Specific Gravity} \times \text{Purity} lb/day of chemical = gal/day × 8.34 × Specific Gravity × Purity

Worked example. A hypochlorite pump draws 780 mL in 10 minutes. The solution is 12.5% available chlorine with a specific gravity of 1.17.

  • Rate: 780 ÷ 10 = 78 mL/min
  • gal/day: (78 × 1,440) ÷ 3,785 = 29.7 gal/day
  • lb/day chlorine: 29.7 × 8.34 × 1.17 × 0.125 = 36.2 lb/day

At a plant flow of 3.0 MGD, that is a dose of: 36.2 3.0 × 8.34 = 1.45 mg/L \frac{36.2}{3.0 \times 8.34} = \textbf{1.45 mg/L} 3.0 × 8.34 36.2 ​ = 1.45 mg/L

2. Dry Chemical Feeders

Type Principle Accuracy

Volumetric — screw, belt, rotary vane, oscillating hopper Delivers a measured volume per unit time Lower — accuracy degrades when bulk density changes with moisture, compaction, or a different supplier lot

Gravimetric — belt with load cell, loss-in-weight Weighs the chemical continuously Higher — unaffected by bulk density changes; more expensive

Calibration by catch and weigh: divert the discharge into a container for a measured time, weigh it, and compute lb/min or lb/day. Compare with the setpoint and adjust.

Dry feed problems

Problem Cause Fix

Bridging / arching in the hopper Moisture, compaction, fine material Vibrators, bin activators, air pads ; keep chemical dry

  • Rat-holing Material flows only through a central channel Bin activator, proper hopper geometry
  • Flooding / flushing Fine aerated powder flows uncontrollably Feeder design, avoid over-aeration
  • Dust Handling and transfer Dust collectors, enclosed transfer, respiratory PPE

Solution line scaling Lime and soda ash deposit hardness scale Periodic acid cleaning of lines; flexible hose that can be flexed to crack scale

Lime slakers

Lime feed is uniquely troublesome. Quicklime (CaO) must be slaked — reacted with water to make Ca(OH)₂ — and the reaction is strongly exothermic . Slakers must control the water-to-lime ratio and temperature, and grit from the lime must be separated and removed. Lime lines scale aggressively and require routine acid cleaning.

3. Gas Chlorinators

Vacuum-operated systems are the standard, because the entire system downstream of the cylinder valve operates under vacuum — if a line breaks, air is drawn in rather than chlorine gas escaping. Components:

  • Vacuum regulator mounted directly on the cylinder valve
  • Rotameter to indicate feed rate
  • V-notch or metering orifice for rate control
  • Ejector (injector) — a venturi that creates the vacuum and mixes chlorine into the water stream

The most common failure is a loss of vacuum , caused by insufficient water supply to the ejector, a plugged or worn ejector throat, or a leak in the vacuum tubing. Symptoms are a rotameter that drops to zero or fluctuates wildly, and loss of residual.

Cylinder cautions:

Feed rate is limited by evaporation. A 150 lb cylinder is generally limited to about 40 lb/day , and a one-ton container to about 400 lb/day , at normal room temperature. Exceeding this freezes the cylinder — frost forms and feed rate collapses.

Never apply heat directly to a cylinder. Warm the room, not the container.

Always chain cylinders upright, keep valve protection hoods on when not connected, and use a new gasket at every connection.

Section 13.2 covers chlorine emergency response in full.

4. Chemical Storage and Handling

Requirement Detail

Segregate incompatibles Never store or feed hypochlorite near acid — mixing releases chlorine gas . Keep acids away from bases, oxidizers away from organics, and cyanides away from all acids (Section 9.3)

Secondary containment Sized to hold the largest tank's volume plus a margin, with no drain to the sewer

Label everything Tanks, fill connections, and feed lines. Color coding and directional labeling of feed lines prevents the classic incident of pumping the wrong chemical into the wrong tank during a delivery

  • Dedicated, keyed fill connections So a delivery driver cannot cross-connect
  • Safety Data Sheets Accessible to every operator on every shift
  • Eyewash and safety shower Within the required travel distance of any handling area, tested weekly

Compatible materials Verify tank, gasket, and pump elastomer compatibility with the specific chemical and concentration

Shelf life Sodium hypochlorite degrades , losing strength faster at higher temperature, higher concentration, and in light. Store cool and dark, rotate stock, and re-verify strength rather than assuming the label value

The hypochlorite degradation trap: a 12.5% delivery stored warm for two months may test at 10% or lower. A plant feeding to a calculated dose based on the label value will silently underdose. Verify strength on receipt and periodically thereafter, and recalculate feed rates accordingly.