Study guide

9.3 Physical/Chemical Industrial Wastewater Treatment

South Carolina Water/Wastewater Operator Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: South Carolina Regulations & Licensing Framework

1.1 SC Environmental Certification Board & Chapter 51 Regulations 1.2 Certification Levels & Experience Requirements 1.3 Facility Classifications & Operator-in-Charge Duties 1.4 Exam Logistics, Scoring & Study Resources

2 Chapter 2: Source Water Characteristics

2.1 Raw Water Sources & Pretreatment 2.2 Groundwater Sources, Wells & GWUDI Determinations 2.3 Watershed Protection & Source Water Contaminants

3 Chapter 3: Water Treatment: Coagulation, Flocculation & Sedimentation

3.1 Coagulation & Flocculation Process Control 3.2 Sedimentation Basins & Clarification

4 Chapter 4: Water Treatment: Filtration

4.1 Granular Media & Membrane Filtration 4.2 Filter Operation, Backwash & Troubleshooting

5 Chapter 5: Water Treatment: Disinfection & Chemical Conditioning

5.1 Chlorination & Chemical Disinfection 5.2 CT Calculations & Disinfection Byproducts Compliance 5.3 Chloramines, Chlorine Dioxide, Ozone & UV 5.4 Corrosion Control & the Lead and Copper Rule 5.5 Fluoridation & Water Softening 5.6 Iron, Manganese, Taste & Odor Control

6 Chapter 6: Water Distribution Systems

6.1 Water Distribution Network Operations & Maintenance 6.2 Cross-Connection Control & Backflow Prevention 6.3 Distribution Hydraulics & Pressure Management 6.4 Pipes, Valves, Hydrants & Appurtenances 6.5 Storage Tanks & Reservoirs 6.6 Water Quality in Distribution: Flushing & Residual Management 6.7 Main Disinfection, Breaks & Repair

7 Chapter 7: Wastewater Collection & Preliminary Treatment

7.1 Wastewater Collection & Preliminary Operations 7.2 Sanitary Sewer Collection System Maintenance 7.3 Lift Station Pumps, Controls & Hydraulics

8 Chapter 8: Wastewater Treatment: Primary & Secondary

8.1 Wastewater Characteristics & Plant Loadings 8.2 Primary Sedimentation & Clarifier Operations 8.3 Activated Sludge Process Control & Operations 8.4 Activated Sludge Troubleshooting 8.5 Aeration Systems & Dissolved Oxygen Control 8.6 Fixed-Film & Lagoon Treatment Systems 8.7 Biological Nutrient Removal & Tertiary Treatment

9 Chapter 9: Wastewater Disinfection, Effluent & Industrial Treatment

9.1 Wastewater Disinfection & Dechlorination 9.2 Effluent Disposal, Reuse & Land Application 9.3 Physical/Chemical Industrial Wastewater Treatment 9.4 Industrial Pretreatment Programs

10 Chapter 10: Solids, Biosolids & Regulatory Permitting

10.1 Sludge Thickening, Digestion & Dewatering 10.2 Biosolids Stabilization & Part 503 Land Application 10.3 Clean Water Act & NPDES Permit Compliance 10.4 Safe Drinking Water Act Compliance & Public Notification

11 Chapter 11: Laboratory Analysis & Quality Control

11.1 Sampling, Preservation & Chain of Custody 11.2 Physical & Chemical Water Quality Analysis 11.3 Wastewater Process Testing & Analytical Methods 11.4 Microbiological Testing & Quality Assurance 11.5 Data Validation, Reporting & Laboratory Certification

12 Chapter 12: Equipment Operation & Maintenance

12.1 Pumps: Types, Curves & Cavitation 12.2 Motors, Drives & Electrical Fundamentals 12.3 Bearings, Seals, Couplings & Lubrication 12.4 Flow Measurement & Process Instrumentation 12.5 Chemical Feed Equipment & Calibration 12.6 SCADA, Controls & Preventive Maintenance Programs

13 Chapter 13: Safety, Security & Administrative Procedures

13.1 Confined Space Entry & Atmospheric Hazards 13.2 Chlorine Gas Safety & Emergency Response 13.3 Lockout/Tagout, PPE, Hazard Communication & Excavation 13.4 Security, Vulnerability Assessment & Emergency Response Planning 13.5 Recordkeeping, Reporting & Administrative Duties

14 Chapter 14: Process Calculations & Hydraulic Math

14.1 Basic Water & Wastewater Math Fundamentals 14.2 Chemical Feed Rate & Dosage Calculations 14.3 Detention Time & Volumetric Flow Calculations 14.4 Removal Efficiency & Process Loading Rates 14.5 Pump Hydraulics & Horsepower Calculations 14.6 Activated Sludge Process Control Math

9.3 Physical/Chemical Industrial Wastewater Treatment

Key Takeaways Explain This Topic AI

South Carolina issues a separate Physical/Chemical Wastewater Treatment Operator license for industrial facilities that treat without biological digestion.

Metal hydroxide solubility is pH-dependent and each metal has its own minimum-solubility pH, so mixed metal wastes require a compromise pH or staged treatment.

Hexavalent chromium must be reduced to trivalent chromium at low pH before it can be precipitated as a hydroxide.

Cyanide is destroyed by alkaline chlorination at pH above 10, and dropping the pH during treatment can release deadly hydrogen cyanide gas.

Dissolved air flotation removes oil, grease, and low-density solids that will not settle by gravity.

Last updated: August 2026

9.3 Physical/Chemical Industrial Wastewater Treatment

South Carolina licenses Physical/Chemical Wastewater Treatment Operators as a discipline entirely separate from biological wastewater, with its own Trainee through Class A ladder and its own facility groups I-P/C through IV-P/C (Section 1.3). The Board's designated references are Sacramento State's Industrial Waste Treatment and Treatment of Metal Wastestreams . If you are sitting the P/C exam, this material is your core.

The defining characteristic: treatment happens by chemistry and physics, not biology. Wastestreams here are frequently toxic to microorganisms, too concentrated, too variable in pH, or simply not biodegradable.

  • 1. Equalization and Neutralization
  • Equalization

Industrial discharge is batch-driven — a plating line dumps a tank, a rinse cycle ends, a shift changes. Without equalization, downstream chemical feed cannot keep up. An equalization basin with adequate mixing dampens both flow and concentration swings and is often the difference between a functioning P/C plant and a chaotic one.

Neutralization

Most subsequent chemistry is pH-dependent, so pH control comes first.

To raise pH (neutralize acid) To lower pH (neutralize base)

Sodium hydroxide (caustic soda) — fast, no sludge, expensive, hazardous Sulfuric acid — cheap, effective, adds sulfate

Lime — Ca(OH)₂ or CaO — cheap, but generates large sludge volumes Hydrochloric acid — fast, more corrosive to equipment

Soda ash, magnesium hydroxide Carbon dioxide — self-limiting, cannot overshoot below about pH 6

The control challenge: the pH titration curve near neutrality is extremely steep, so a tiny reagent overshoot swings pH several units. Practical control uses multi-stage neutralization — a coarse stage followed by a trim stage — with adequate mixing and probes placed where they see fully mixed liquid, never immediately at the injection point.

2. Chemical Precipitation of Metals

The workhorse of industrial metals treatment: raise pH so dissolved metal ions form insoluble metal hydroxides that can be coagulated, settled, and dewatered. M 2 + + 2 OH − → M(OH) 2 ↓ \text{M}^{2+} + 2\text{OH}^- \rightarrow \text{M(OH)}_2 \downarrow M 2 + + 2 OH − → M(OH) 2 ​ ↓

The critical concept — each metal has its own optimum pH

  • Metal Approximate minimum-solubility pH
  • Chromium (trivalent) ~7.5–8.5
  • Copper ~8.0–9.0
  • Zinc ~9.0–9.5
  • Nickel ~10.0–11.0
  • Cadmium ~10.0–11.0
  • Lead ~9.0–9.5

Amphoteric behavior is the trap. Metals such as zinc, lead, chromium, and aluminum redissolve if pH goes too high — their solubility curve is a U shape with a minimum, not a downward slope. An operator who reasons "more caustic means more removal" will drive zinc back into solution and violate the permit.

Where a wastestream carries several metals with incompatible optima, options are:

  • Operate at a compromise pH accepting partial removal of each,
  • Use staged precipitation at two different pH values with clarification between, or

Use sulfide precipitation — metal sulfides are far less soluble than hydroxides across a wider pH range, at the cost of handling sulfide reagents and the risk of hydrogen sulfide generation if pH falls.

Chelating agents such as EDTA, ammonia, and citrate hold metals in solution and defeat hydroxide precipitation entirely. They must be broken with oxidation or handled with sulfide, and the real answer is usually source segregation.

  • 3. Oxidation and Reduction — The Two Classic Sequences
  • Hexavalent chromium reduction

Cr⁶⁺ is highly toxic and does not precipitate as a hydroxide . It must first be reduced to Cr³⁺ :

Lower pH to about 2–3 with sulfuric acid.

Add a reducing agent — sodium metabisulfite, sodium bisulfite, or sulfur dioxide .

Cr⁶⁺ → Cr³⁺ , monitored by ORP (oxidation-reduction potential).

Raise pH to about 8–9 to precipitate Cr(OH)₃ .

Clarify and dewater.

The exam point: reduction happens at LOW pH, precipitation at HIGH pH. Reversing them accomplishes nothing.

Cyanide destruction — alkaline chlorination

Raise pH above 10 — this is a safety-critical step.

Add chlorine or hypochlorite. Cyanide is oxidized to cyanate (CNO⁻) .

Optionally continue at pH ~8–8.5 to oxidize cyanate to carbon dioxide and nitrogen.

Then proceed to metals precipitation.

Deadly hazard: if pH drops below about 8.5 while cyanide is present, hydrogen cyanide (HCN) gas is released. HCN is rapidly lethal. Alkaline pH must be established before any chlorine is added and maintained throughout, with pH alarms and interlocks. Never store or feed acid and cyanide-bearing waste where a mixing accident is possible , and never mix cyanide and acid wastestreams.

4. Physical Separation Processes

Process Principle Best for

Gravity sedimentation / clarification Particles denser than water settle Precipitated metal hydroxides, heavy solids

Dissolved air flotation (DAF) Pressurized recycle releases microbubbles that attach to particles and float them to a skimmed surface Oil, grease, fibers, and low-density solids that will not settle

API separator Gravity separation of free oil Free, non-emulsified oil

Emulsion breaking Acid, heat, or polymer destabilizes an oil-water emulsion Emulsified oils; must precede DAF or separation

  • Filtration Media, cartridge, or bag Polishing after clarification
  • Membranes (UF, NF, RO) Size and charge exclusion Concentrated recovery, high-purity reuse
  • Ion exchange Resin exchanges ions Metals recovery, deionized water production
  • Carbon adsorption Adsorption on activated carbon Dissolved organics, solvents, color
  • Air / steam stripping Volatiles transferred to a gas phase VOCs, ammonia
  • Evaporation / crystallization Water removed as vapor Zero liquid discharge systems
  • 5. Residuals

Physical/chemical treatment generates chemical sludge , not biosolids. It is typically thickened, then dewatered by filter press, belt press, or centrifuge . The critical difference from municipal biosolids is regulatory: metal-bearing sludge is frequently a hazardous waste subject to RCRA characterization by toxicity characteristic leaching procedure (TCLP) testing, and disposal costs are far higher. Lime-based precipitation produces substantially more sludge than caustic , which is a real operating cost trade-off. Reducing sludge volume by segregating clean streams at the source is nearly always cheaper than treating and disposing of it.