Study guide
5.4 Corrosion Control & the Lead and Copper Rule
South Carolina Water/Wastewater Operator Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: South Carolina Regulations & Licensing Framework
1.1 SC Environmental Certification Board & Chapter 51 Regulations 1.2 Certification Levels & Experience Requirements 1.3 Facility Classifications & Operator-in-Charge Duties 1.4 Exam Logistics, Scoring & Study Resources
2 Chapter 2: Source Water Characteristics
2.1 Raw Water Sources & Pretreatment 2.2 Groundwater Sources, Wells & GWUDI Determinations 2.3 Watershed Protection & Source Water Contaminants
3 Chapter 3: Water Treatment: Coagulation, Flocculation & Sedimentation
3.1 Coagulation & Flocculation Process Control 3.2 Sedimentation Basins & Clarification
4 Chapter 4: Water Treatment: Filtration
4.1 Granular Media & Membrane Filtration 4.2 Filter Operation, Backwash & Troubleshooting
5 Chapter 5: Water Treatment: Disinfection & Chemical Conditioning
5.1 Chlorination & Chemical Disinfection 5.2 CT Calculations & Disinfection Byproducts Compliance 5.3 Chloramines, Chlorine Dioxide, Ozone & UV 5.4 Corrosion Control & the Lead and Copper Rule 5.5 Fluoridation & Water Softening 5.6 Iron, Manganese, Taste & Odor Control
6 Chapter 6: Water Distribution Systems
6.1 Water Distribution Network Operations & Maintenance 6.2 Cross-Connection Control & Backflow Prevention 6.3 Distribution Hydraulics & Pressure Management 6.4 Pipes, Valves, Hydrants & Appurtenances 6.5 Storage Tanks & Reservoirs 6.6 Water Quality in Distribution: Flushing & Residual Management 6.7 Main Disinfection, Breaks & Repair
7 Chapter 7: Wastewater Collection & Preliminary Treatment
7.1 Wastewater Collection & Preliminary Operations 7.2 Sanitary Sewer Collection System Maintenance 7.3 Lift Station Pumps, Controls & Hydraulics
8 Chapter 8: Wastewater Treatment: Primary & Secondary
8.1 Wastewater Characteristics & Plant Loadings 8.2 Primary Sedimentation & Clarifier Operations 8.3 Activated Sludge Process Control & Operations 8.4 Activated Sludge Troubleshooting 8.5 Aeration Systems & Dissolved Oxygen Control 8.6 Fixed-Film & Lagoon Treatment Systems 8.7 Biological Nutrient Removal & Tertiary Treatment
9 Chapter 9: Wastewater Disinfection, Effluent & Industrial Treatment
9.1 Wastewater Disinfection & Dechlorination 9.2 Effluent Disposal, Reuse & Land Application 9.3 Physical/Chemical Industrial Wastewater Treatment 9.4 Industrial Pretreatment Programs
10 Chapter 10: Solids, Biosolids & Regulatory Permitting
10.1 Sludge Thickening, Digestion & Dewatering 10.2 Biosolids Stabilization & Part 503 Land Application 10.3 Clean Water Act & NPDES Permit Compliance 10.4 Safe Drinking Water Act Compliance & Public Notification
11 Chapter 11: Laboratory Analysis & Quality Control
11.1 Sampling, Preservation & Chain of Custody 11.2 Physical & Chemical Water Quality Analysis 11.3 Wastewater Process Testing & Analytical Methods 11.4 Microbiological Testing & Quality Assurance 11.5 Data Validation, Reporting & Laboratory Certification
12 Chapter 12: Equipment Operation & Maintenance
12.1 Pumps: Types, Curves & Cavitation 12.2 Motors, Drives & Electrical Fundamentals 12.3 Bearings, Seals, Couplings & Lubrication 12.4 Flow Measurement & Process Instrumentation 12.5 Chemical Feed Equipment & Calibration 12.6 SCADA, Controls & Preventive Maintenance Programs
13 Chapter 13: Safety, Security & Administrative Procedures
13.1 Confined Space Entry & Atmospheric Hazards 13.2 Chlorine Gas Safety & Emergency Response 13.3 Lockout/Tagout, PPE, Hazard Communication & Excavation 13.4 Security, Vulnerability Assessment & Emergency Response Planning 13.5 Recordkeeping, Reporting & Administrative Duties
14 Chapter 14: Process Calculations & Hydraulic Math
14.1 Basic Water & Wastewater Math Fundamentals 14.2 Chemical Feed Rate & Dosage Calculations 14.3 Detention Time & Volumetric Flow Calculations 14.4 Removal Efficiency & Process Loading Rates 14.5 Pump Hydraulics & Horsepower Calculations 14.6 Activated Sludge Process Control Math
5.4 Corrosion Control & the Lead and Copper Rule
Key Takeaways Explain This Topic AI
The lead action level is 0.015 mg/L and the copper action level is 1.3 mg/L, both evaluated at the 90th percentile of first-draw tap samples.
Action levels are not MCLs; exceeding one triggers treatment, monitoring, public education, and possible service line replacement rather than an automatic violation.
Lead and copper compliance samples are first-draw, one-liter samples taken after at least six hours of stagnation from cold-water taps.
The Langelier Saturation Index indicates whether water tends to deposit or dissolve calcium carbonate, with negative values indicating corrosive water.
Orthophosphate is the most widely used corrosion inhibitor because it forms a low-solubility protective scale on lead and copper surfaces.
Last updated: August 2026
5.4 Corrosion Control & the Lead and Copper Rule
Lead almost never comes out of a river or an aquifer. It comes out of lead service lines, lead solder, and brass fixtures between the water main and the consumer's tap. That single fact reframes the operator's job: you are not removing a contaminant at the plant, you are conditioning the water so it stops dissolving the pipe . In South Carolina this also drives facility classification — adding corrosion control treatment places a plant in Group II , requiring at least a Class D operator-in-charge.
1. What Corrosion Actually Is
Corrosion is an electrochemical process. A galvanic cell forms with four parts:
- Anode — metal oxidizes and dissolves into the water (this is where pipe is lost)
- Cathode — reduction occurs, commonly of dissolved oxygen
- Electrolyte — the water itself, carrying ions
- Metallic path — the pipe wall connecting anode and cathode
Remove any one and corrosion stops. Practical control usually attacks the electrolyte — the water chemistry.
Factors that accelerate corrosion
- Factor Effect
- Low pH Strongly increases metal solubility; the dominant lever
- Low alkalinity Little buffering, so pH swings and scale will not form
- High dissolved oxygen and free chlorine Support the cathodic reaction
- High temperature Roughly doubles reaction rate per 10 °C
- High velocity Erosion corrosion, especially at elbows in copper
- Dissimilar metals joined Galvanic corrosion; the less noble metal sacrifices
- High chloride or sulfate relative to alkalinity Aggressive to lead solder and brass
- 2. Saturation Indices
The Langelier Saturation Index (LSI) compares actual pH to the pH at which the water would be saturated with calcium carbonate: LSI = pH actual − pH s \text{LSI} = \text{pH}_{\text{actual}} - \text{pH}_{s} LSI = pH actual − pH s
- LSI Tendency
- Positive Supersaturated — tends to deposit calcium carbonate scale
- Zero At equilibrium
- Negative Undersaturated — corrosive , tends to dissolve scale and pipe
A slightly positive LSI is the classic target. But be careful with the exam framing: a calcium carbonate film is a blunt tool and modern practice relies more on orthophosphate passivation than on deliberate scaling, because heavy scale reduces carrying capacity and does not protect lead well on its own.
3. Corrosion Control Treatment
Approach Chemicals Notes
pH and alkalinity adjustment Lime, soda ash, caustic soda, sodium bicarbonate The first and most powerful lever. Raising pH toward 7.5–9 sharply lowers lead solubility
Orthophosphate inhibitor Phosphoric acid, zinc orthophosphate, blended ortho/polyphosphate Forms an insoluble lead- and copper-phosphate film. The most common modern approach. Typical dose ~1–3 mg/L as PO₄
Silicate inhibitor Sodium silicate Less common; forms a protective silicate film
Calcium carbonate saturation Lime addition to a positive LSI Older approach, still used where alkalinity is very low
Critical operating rule: never make an abrupt change in source water, pH, or disinfectant without evaluating the corrosion consequences. Changing water chemistry can destabilize an existing protective scale and release accumulated lead. This is the mechanism behind the best-known lead crises in the United States, and it is heavily tested.
- 4. The Lead and Copper Rule
- Action levels — not MCLs
- Metal Action level Basis
- Lead 0.015 mg/L (15 ppb) 90th percentile of first-draw tap samples
- Copper 1.3 mg/L 90th percentile of first-draw tap samples
An action level is not a maximum contaminant level. Exceeding it is not automatically a violation; it triggers required actions . Failing to perform those actions is the violation.
How the 90th percentile works
Rank all sample results from lowest to highest. With 20 samples , the 90th percentile is the 18th value (20 × 0.9 = 18). If that value exceeds 0.015 mg/L, the system has a lead action level exceedance — even if 17 homes were perfectly clean.
Sampling protocol — the details are testable
First-draw sample, collected after the water has stood motionless in the plumbing for at least 6 hours .
One liter , from a cold-water kitchen or bathroom tap normally used for consumption.
Taken from Tier 1 sites — the highest-risk locations: homes with lead service lines, lead solder, or lead interior plumbing.
Do not remove or clean the aerator before sampling, and do not pre-flush.
What an exceedance triggers
Water quality parameter monitoring and installation or optimization of corrosion control treatment .
Public education delivered on a required schedule, and individual notification of sampled residents.
Source water monitoring and treatment where source contribution is significant.
Lead service line replacement obligations where a lead action level exceedance persists.
Increased tap sampling frequency until the system returns to compliance.
Service line inventory and records
Systems must develop and maintain a service line material inventory identifying lead, galvanized-requiring-replacement, non-lead, and unknown materials on both the utility and customer sides. As noted in Section 1.3, lead and copper tap monitoring results and service line inventory records are retained for 12 years — the longest retention in the drinking-water rules.
5. Copper-Specific Behavior
Copper leaching is worst in new copper plumbing before a protective oxide film develops, and is aggravated by low pH, high free chlorine, and high velocity . Blue-green staining of fixtures and a metallic taste are the field indicators. Pinhole leaks in copper often trace to erosion corrosion at elbows where velocity is excessive, or to aggressive water with low pH and low alkalinity.