Study guide

5.6 Iron, Manganese, Taste & Odor Control

South Carolina Water/Wastewater Operator Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: South Carolina Regulations & Licensing Framework

1.1 SC Environmental Certification Board & Chapter 51 Regulations 1.2 Certification Levels & Experience Requirements 1.3 Facility Classifications & Operator-in-Charge Duties 1.4 Exam Logistics, Scoring & Study Resources

2 Chapter 2: Source Water Characteristics

2.1 Raw Water Sources & Pretreatment 2.2 Groundwater Sources, Wells & GWUDI Determinations 2.3 Watershed Protection & Source Water Contaminants

3 Chapter 3: Water Treatment: Coagulation, Flocculation & Sedimentation

3.1 Coagulation & Flocculation Process Control 3.2 Sedimentation Basins & Clarification

4 Chapter 4: Water Treatment: Filtration

4.1 Granular Media & Membrane Filtration 4.2 Filter Operation, Backwash & Troubleshooting

5 Chapter 5: Water Treatment: Disinfection & Chemical Conditioning

5.1 Chlorination & Chemical Disinfection 5.2 CT Calculations & Disinfection Byproducts Compliance 5.3 Chloramines, Chlorine Dioxide, Ozone & UV 5.4 Corrosion Control & the Lead and Copper Rule 5.5 Fluoridation & Water Softening 5.6 Iron, Manganese, Taste & Odor Control

6 Chapter 6: Water Distribution Systems

6.1 Water Distribution Network Operations & Maintenance 6.2 Cross-Connection Control & Backflow Prevention 6.3 Distribution Hydraulics & Pressure Management 6.4 Pipes, Valves, Hydrants & Appurtenances 6.5 Storage Tanks & Reservoirs 6.6 Water Quality in Distribution: Flushing & Residual Management 6.7 Main Disinfection, Breaks & Repair

7 Chapter 7: Wastewater Collection & Preliminary Treatment

7.1 Wastewater Collection & Preliminary Operations 7.2 Sanitary Sewer Collection System Maintenance 7.3 Lift Station Pumps, Controls & Hydraulics

8 Chapter 8: Wastewater Treatment: Primary & Secondary

8.1 Wastewater Characteristics & Plant Loadings 8.2 Primary Sedimentation & Clarifier Operations 8.3 Activated Sludge Process Control & Operations 8.4 Activated Sludge Troubleshooting 8.5 Aeration Systems & Dissolved Oxygen Control 8.6 Fixed-Film & Lagoon Treatment Systems 8.7 Biological Nutrient Removal & Tertiary Treatment

9 Chapter 9: Wastewater Disinfection, Effluent & Industrial Treatment

9.1 Wastewater Disinfection & Dechlorination 9.2 Effluent Disposal, Reuse & Land Application 9.3 Physical/Chemical Industrial Wastewater Treatment 9.4 Industrial Pretreatment Programs

10 Chapter 10: Solids, Biosolids & Regulatory Permitting

10.1 Sludge Thickening, Digestion & Dewatering 10.2 Biosolids Stabilization & Part 503 Land Application 10.3 Clean Water Act & NPDES Permit Compliance 10.4 Safe Drinking Water Act Compliance & Public Notification

11 Chapter 11: Laboratory Analysis & Quality Control

11.1 Sampling, Preservation & Chain of Custody 11.2 Physical & Chemical Water Quality Analysis 11.3 Wastewater Process Testing & Analytical Methods 11.4 Microbiological Testing & Quality Assurance 11.5 Data Validation, Reporting & Laboratory Certification

12 Chapter 12: Equipment Operation & Maintenance

12.1 Pumps: Types, Curves & Cavitation 12.2 Motors, Drives & Electrical Fundamentals 12.3 Bearings, Seals, Couplings & Lubrication 12.4 Flow Measurement & Process Instrumentation 12.5 Chemical Feed Equipment & Calibration 12.6 SCADA, Controls & Preventive Maintenance Programs

13 Chapter 13: Safety, Security & Administrative Procedures

13.1 Confined Space Entry & Atmospheric Hazards 13.2 Chlorine Gas Safety & Emergency Response 13.3 Lockout/Tagout, PPE, Hazard Communication & Excavation 13.4 Security, Vulnerability Assessment & Emergency Response Planning 13.5 Recordkeeping, Reporting & Administrative Duties

14 Chapter 14: Process Calculations & Hydraulic Math

14.1 Basic Water & Wastewater Math Fundamentals 14.2 Chemical Feed Rate & Dosage Calculations 14.3 Detention Time & Volumetric Flow Calculations 14.4 Removal Efficiency & Process Loading Rates 14.5 Pump Hydraulics & Horsepower Calculations 14.6 Activated Sludge Process Control Math

5.6 Iron, Manganese, Taste & Odor Control

Key Takeaways Explain This Topic AI

Iron carries a secondary standard of 0.3 mg/L and manganese a secondary standard of 0.05 mg/L, both aesthetic rather than health-based.

Iron produces red or rust staining while manganese produces black staining, and manganese is far harder to oxidize.

Oxidation followed by filtration is the standard removal train, using aeration, chlorine, potassium permanganate, or ozone.

Sequestering with polyphosphate holds low concentrations in solution but does not remove them and fails when the water is heated.

Manganese greensand uses a manganese dioxide coating regenerated with potassium permanganate to catalyze oxidation.

Last updated: August 2026

5.6 Iron, Manganese, Taste & Odor Control

These are the complaints that generate customer phone calls. None of them is a health violation — iron, manganese, and odor are all governed by secondary standards — but they drive public confidence in the utility, and the standardized exam tests them because they are daily operational reality in South Carolina, where groundwater systems and stratified reservoirs both deliver them reliably.

1. Iron and Manganese: Chemistry First

In anoxic water — deep groundwater or the summer hypolimnion of a reservoir — iron and manganese exist in reduced, dissolved, colorless form:

  • Ferrous iron, Fe²⁺ — soluble, invisible
  • Manganous manganese, Mn²⁺ — soluble, invisible

Expose that water to oxygen or an oxidant and they convert to oxidized, insoluble, highly visible forms:

  • Ferric iron, Fe³⁺ → reddish-brown Fe(OH)₃ particulate
  • Manganic manganese, Mn⁴⁺ → black MnO₂ particulate

This is why a customer reports "clear water that turns rusty in the glass" — the iron was dissolved at the tap and oxidized on contact with air.

  • Iron Manganese
  • Secondary MCL 0.3 mg/L 0.05 mg/L
  • Staining color Red, orange, rust Black , brown-black
  • Taste Metallic, bitter Metallic, oily
  • Ease of oxidation Relatively easy Much harder — needs higher pH, longer contact, or a stronger oxidant

The key operational asymmetry: manganese oxidizes far more slowly than iron. Chlorine oxidizes iron readily at ordinary pH, but oxidizing manganese with chlorine requires pH above roughly 9.5 and substantial contact time. A plant that treats manganese with chlorine at pH 7 will pass dissolved manganese through the filters, where it oxidizes later in the distribution system and produces black water complaints far from the plant — a classic exam scenario.

2. Removal Options

Oxidation and filtration — the standard train Oxidize → Allow contact time → Filter the precipitate \text{Oxidize} \rightarrow \text{Allow contact time} \rightarrow \text{Filter the precipitate} Oxidize → Allow contact time → Filter the precipitate

  • Oxidant Strength for Fe Strength for Mn Notes
  • Aeration Good Poor Cheapest; also strips CO₂ and H₂S and raises pH
  • Chlorine Good Only at high pH Forms DBPs with organic matter

Potassium permanganate (KMnO₄) Excellent Excellent The classic manganese oxidant. Overfeeding turns the water pink — an immediate visual alarm

  • Chlorine dioxide Excellent Excellent No THM formation; chlorite is regulated
  • Ozone Excellent Excellent Strongest; watch for bromate

Manganese greensand deserves its own note: the media carries a manganese dioxide coating that catalyzes oxidation, and it is regenerated with potassium permanganate , either continuously or intermittently. It is the workhorse for small groundwater systems with manganese problems.

Sequestering — control, not removal

Polyphosphate sequestering agents complex iron and manganese and hold them in solution so they never precipitate or stain.

Works only at low concentrations — generally below about 1.0 mg/L combined .

Nothing is removed. The metals are still in the water.

Heat breaks the complex. Polyphosphate reverts to orthophosphate in a water heater, releasing the metal and producing staining in hot water even though cold water is clear. This is the classic sequestering failure and a frequent exam question.

Feed before any oxidant, or the metals oxidize before they can be sequestered.

Ion exchange and lime softening

Both remove iron and manganese incidentally. Ion exchange resin, however, is fouled by iron and manganese unless they are removed first — so ion exchange is not a treatment for them, it is a victim of them.

3. Taste and Odor: Diagnose Before You Treat

Description Likely cause Correct response

Earthy, musty, moldy Geosmin and MIB from algae and actinomycetes PAC or GAC ; oxidants alone are ineffective and chlorine can worsen it

Rotten eggs Hydrogen sulfide (H₂S) from anoxic groundwater or the hypolimnion Aeration to strip it, or oxidation with chlorine, permanganate, or ozone

Swimming pool, chlorinous, medicinal Dichloramine and trichloramine from combined chlorine; chlorophenols Move past breakpoint to a free residual; find and remove the phenol source

  • Metallic Iron, manganese, copper, zinc Oxidize and filter, or sequester; check corrosion control
  • Grassy, fishy, septic Algal decay products PAC; consider changing intake depth

Petroleum, solvent Contamination event Investigate immediately — this is a potential emergency, not an aesthetic issue

Powdered vs. granular activated carbon

  • PAC GAC
  • Application Dosed as a slurry during episodic events Fixed contactor or filter media, continuous
  • Best for Seasonal blooms, spills Chronic taste and odor, TOC/DBP precursor removal

Feed point As early as possible for contact time — but not with the oxidant , which consumes the carbon's capacity N/A

Cost profile Low capital, high unit cost when running High capital, lower cost when run continuously

Threshold Odor Number (TON) is the standard measure: the dilution factor at which the odor becomes barely detectable. A TON of 4 means the sample had to be diluted fourfold before the odor disappeared. The secondary standard for odor is a TON of 3 .

Exam framing: the trap is reaching for more chlorine. For geosmin and MIB, more chlorine does nothing useful and increases DBPs. For chlorinous odors, more chlorine is actually correct — because the goal is to push past breakpoint. Knowing which situation you are in is the whole question.