Study guide

6.5 Storage Tanks & Reservoirs

South Carolina Water/Wastewater Operator Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: South Carolina Regulations & Licensing Framework

1.1 SC Environmental Certification Board & Chapter 51 Regulations 1.2 Certification Levels & Experience Requirements 1.3 Facility Classifications & Operator-in-Charge Duties 1.4 Exam Logistics, Scoring & Study Resources

2 Chapter 2: Source Water Characteristics

2.1 Raw Water Sources & Pretreatment 2.2 Groundwater Sources, Wells & GWUDI Determinations 2.3 Watershed Protection & Source Water Contaminants

3 Chapter 3: Water Treatment: Coagulation, Flocculation & Sedimentation

3.1 Coagulation & Flocculation Process Control 3.2 Sedimentation Basins & Clarification

4 Chapter 4: Water Treatment: Filtration

4.1 Granular Media & Membrane Filtration 4.2 Filter Operation, Backwash & Troubleshooting

5 Chapter 5: Water Treatment: Disinfection & Chemical Conditioning

5.1 Chlorination & Chemical Disinfection 5.2 CT Calculations & Disinfection Byproducts Compliance 5.3 Chloramines, Chlorine Dioxide, Ozone & UV 5.4 Corrosion Control & the Lead and Copper Rule 5.5 Fluoridation & Water Softening 5.6 Iron, Manganese, Taste & Odor Control

6 Chapter 6: Water Distribution Systems

6.1 Water Distribution Network Operations & Maintenance 6.2 Cross-Connection Control & Backflow Prevention 6.3 Distribution Hydraulics & Pressure Management 6.4 Pipes, Valves, Hydrants & Appurtenances 6.5 Storage Tanks & Reservoirs 6.6 Water Quality in Distribution: Flushing & Residual Management 6.7 Main Disinfection, Breaks & Repair

7 Chapter 7: Wastewater Collection & Preliminary Treatment

7.1 Wastewater Collection & Preliminary Operations 7.2 Sanitary Sewer Collection System Maintenance 7.3 Lift Station Pumps, Controls & Hydraulics

8 Chapter 8: Wastewater Treatment: Primary & Secondary

8.1 Wastewater Characteristics & Plant Loadings 8.2 Primary Sedimentation & Clarifier Operations 8.3 Activated Sludge Process Control & Operations 8.4 Activated Sludge Troubleshooting 8.5 Aeration Systems & Dissolved Oxygen Control 8.6 Fixed-Film & Lagoon Treatment Systems 8.7 Biological Nutrient Removal & Tertiary Treatment

9 Chapter 9: Wastewater Disinfection, Effluent & Industrial Treatment

9.1 Wastewater Disinfection & Dechlorination 9.2 Effluent Disposal, Reuse & Land Application 9.3 Physical/Chemical Industrial Wastewater Treatment 9.4 Industrial Pretreatment Programs

10 Chapter 10: Solids, Biosolids & Regulatory Permitting

10.1 Sludge Thickening, Digestion & Dewatering 10.2 Biosolids Stabilization & Part 503 Land Application 10.3 Clean Water Act & NPDES Permit Compliance 10.4 Safe Drinking Water Act Compliance & Public Notification

11 Chapter 11: Laboratory Analysis & Quality Control

11.1 Sampling, Preservation & Chain of Custody 11.2 Physical & Chemical Water Quality Analysis 11.3 Wastewater Process Testing & Analytical Methods 11.4 Microbiological Testing & Quality Assurance 11.5 Data Validation, Reporting & Laboratory Certification

12 Chapter 12: Equipment Operation & Maintenance

12.1 Pumps: Types, Curves & Cavitation 12.2 Motors, Drives & Electrical Fundamentals 12.3 Bearings, Seals, Couplings & Lubrication 12.4 Flow Measurement & Process Instrumentation 12.5 Chemical Feed Equipment & Calibration 12.6 SCADA, Controls & Preventive Maintenance Programs

13 Chapter 13: Safety, Security & Administrative Procedures

13.1 Confined Space Entry & Atmospheric Hazards 13.2 Chlorine Gas Safety & Emergency Response 13.3 Lockout/Tagout, PPE, Hazard Communication & Excavation 13.4 Security, Vulnerability Assessment & Emergency Response Planning 13.5 Recordkeeping, Reporting & Administrative Duties

14 Chapter 14: Process Calculations & Hydraulic Math

14.1 Basic Water & Wastewater Math Fundamentals 14.2 Chemical Feed Rate & Dosage Calculations 14.3 Detention Time & Volumetric Flow Calculations 14.4 Removal Efficiency & Process Loading Rates 14.5 Pump Hydraulics & Horsepower Calculations 14.6 Activated Sludge Process Control Math

6.5 Storage Tanks & Reservoirs

Key Takeaways Explain This Topic AI

Distribution storage serves three purposes: equalizing demand, providing fire flow reserve, and supplying emergency reserve during outages.

Elevated tanks and standpipes float on the system and set the hydraulic grade line, while ground storage usually requires booster pumping.

Inadequate turnover is the leading water quality problem in storage, producing residual loss, nitrification, and thermal stratification.

Tank vents and overflows must be screened and the overflow must discharge through an air gap, never submerged or directly connected to a sewer.

Tanks must be inspected on a regular cycle and disinfected after cleaning or repair before returning to service.

Last updated: August 2026

6.5 Storage Tanks & Reservoirs

Storage is where the distribution system's water sits still — and standing water is where water quality goes to die. Operators are tested both on why storage exists and on the specific sanitary defects that turn a tank into a contamination pathway.

1. Why Storage Exists

Purpose What it does

Equalization Lets the plant and wells run at a steady average rate while the tank absorbs peak-hour demand. Without it, source and pumping capacity would have to match peak instantaneous demand

Fire flow reserve Holds a dedicated volume for firefighting, usually the controlling factor in sizing storage for small systems

Emergency reserve Keeps water flowing during power failure, main break, pump failure, or a plant shutdown

Pressure stabilization Elevated storage floats on the system and holds the hydraulic grade line steady, damping pressure fluctuation

Storage also reduces energy cost by letting pumps run during off-peak power periods.

2. Storage Types

Type Description Hydraulics

Elevated tank Bowl on a tower or pedestal Floats on the system ; sets the hydraulic grade line directly. All usable volume is at useful pressure

Standpipe Tall cylindrical ground-supported tank Only the upper portion is at useful pressure; the lower portion is effectively dead storage requiring pumping

Ground storage reservoir Large-volume tank at grade Requires booster pumping to serve the system

Hydropneumatic tank Pressure vessel with an air cushion Small systems; very little usable volume, primarily controls pump cycling

Clearwell At the plant, downstream of filters Provides disinfection contact time for CT credit and buffers between filtration and high-service pumping

Note the exam distinction: a clearwell's primary job is contact time , not distribution storage.

3. Turnover — The Central Water Quality Issue

Water sitting in a tank for days loses disinfectant residual, warms, stratifies, and grows biofilm. Good practice targets complete turnover in roughly 3 to 5 days , achieved by cycling the level meaningfully rather than holding the tank nearly full.

Symptoms of poor turnover

Disinfectant residual falls at the tank outlet compared with the inlet.

Heterotrophic plate counts rise ; coliform positives appear near the tank.

Nitrification in chloraminated systems — falling chloramine residual with rising nitrite and nitrate, as described in Section 5.3.

Thermal stratification — warm water layers on top and never mixes, so a fraction of the tank is effectively stagnant year-round.

Taste, odor, and color complaints concentrated in the tank's service area.

Corrective measures

  • Measure Effect
  • Increase level cycling Deeper daily draw-down forces exchange of the stored volume

Separate inlet and outlet piping A single common inlet/outlet pipe lets fresh water enter and immediately leave, leaving the bulk stagnant — this is the classic design defect

  • Active mixing systems Mechanical or passive mixers break thermal stratification
  • Deep-cycle then refill Periodic aggressive draw-down to exchange the full volume
  • Booster disinfection at the tank Restores residual where turnover alone cannot
  • Reduce oversized storage Some systems simply hold more storage than demand can turn over
  • 4. Sanitary Defects — The Inspection Checklist

These are exactly the items a sanitary survey looks for, and they are prime exam material:

Component Requirement

Hatches and access openings Locked , with a raised curb at least 4 inches and an overlapping, downward-shielded cover with a gasket

Vents Must be present and sized for maximum flow, downturned or otherwise shielded , and screened (commonly 24-mesh corrosion-resistant) to exclude insects, birds, and debris

Overflow Screened , downturned , and discharging over an air gap — never submerged, never directly connected to a sewer or storm drain

  • Drain Discharged through an air gap
  • Roof and seams Watertight; no ponding, no openings, no bird access

Coating and cathodic protection Interior coating intact and NSF/ANSI 61 certified ; cathodic protection functioning

Site Fenced, secured, graded to drain away from the structure

The single most-tested defect: a submerged overflow or an overflow piped directly into a sewer creates a direct cross-connection between the finished water storage and the sewer. The overflow must always terminate above grade with a visible air gap and a screened, downturned opening.

5. Inspection, Cleaning, and Return to Service

Inspection frequency: exterior inspections should be frequent and routine; interior inspections are commonly performed on a 3-to-5-year cycle , by draining and entering, by diver, or by remotely operated vehicle. Sediment accumulation, coating failure, corrosion, and structural defects are the findings that drive maintenance.

Confined space: entering a drained tank is a permit-required confined space entry . Every requirement in Section 13.1 applies — atmospheric testing, ventilation, attendant, retrieval equipment, and permit.

Disinfection before return to service

Any tank that has been drained, cleaned, coated, or repaired must be disinfected before it is returned to service , following AWWA C652. Three accepted methods:

Method Approach

Chlorination Method 1 Fill the tank with water dosed to about 10 mg/L free chlorine and hold for at least 6 hours

Chlorination Method 2 Spray or brush all interior surfaces with a strong solution of roughly 200 mg/L and hold at least 30 minutes

Chlorination Method 3 Fill about 5% of the tank volume with water dosed to about 50 mg/L , hold 6 hours , then fill to overflow and hold a further period

After disinfection, the tank is drained or the water is neutralized and disposed of appropriately, then refilled and sampled for bacteriological analysis . Two consecutive satisfactory samples taken 24 hours apart are required before the tank returns to service. Highly chlorinated water must be dechlorinated before discharge to protect receiving waters — see Section 9.1.