Study guide

16.2 Speed Control, Direction & Rotating Field Methods

CAAS SAR-66 AML Module 3 — Electrical Fundamentals Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Knowledge Levels & Study Approach for Module 3

2 Electron Theory & Static Electricity

2.1 Electron Theory & Atomic Structure 2.2 Conductors, Semiconductors & Insulators 2.3 Static Electricity, Coulomb's Law & Conduction

3 Terminology & Generation of Electricity

3.1 Electrical Terminology 3.2 Generation of Electricity

4 DC Sources of Electricity

4.1 Primary & Secondary Cells 4.2 Lead-Acid & Nickel-Cadmium Batteries 4.3 Series/Parallel Cells, Internal Resistance, Thermocouples & Photocells

5 DC Circuits

5.1 Ohm's Law 5.2 Kirchhoff's Voltage & Current Laws 5.3 Series/Parallel Networks & Supply Internal Resistance

6 Resistance & Resistors

6.1 Resistivity & Factors Affecting Resistance 6.2 Resistor Colour Code, Tolerance & Preferred Values 6.3 Series/Parallel Resistors, Potentiometers & Rheostats 6.4 Wheatstone Bridge, Thermistors & Temperature Coefficient

7 Power, Work & Energy

7.1 Power, Work & Energy Concepts 7.2 Power Dissipation & Calculations

8 Capacitance & Capacitors

8.1 Capacitor Operation & Factors Affecting Capacitance 8.2 Series/Parallel Capacitors & Types 8.3 RC Time Constants, Energy Storage & Testing

9 Magnetism

9.1 Theory of Magnetism & Magnetic Materials 9.2 Electromagnets & Hand Rules 9.3 MMF, Flux Density, Permeability, Hysteresis & Eddy Currents

10 Inductance & Inductors

10.1 Faraday's Law & Induced Voltage 10.2 Self & Mutual Inductance, Lenz's Law 10.3 Back EMF, Saturation & Inductor Applications

11 DC Motor/Generator Theory

11.1 Basic Motor & Generator Theory 11.2 DC Generators — Construction & Operation 11.3 DC Motors — Series, Shunt, Compound & Starter-Generators

12 AC Theory

12.1 Sinusoidal Waveforms — Phase, Period, Frequency 12.2 Peak, Average, RMS Values & Calculations 12.3 Non-Sinusoidal Waves & Single/Three-Phase Principles

13 R, L & C Circuits

13.1 Phase Relationships in R, L, C Circuits 13.2 Impedance, Phase Angle & Power Factor 13.3 True, Apparent & Reactive Power

14 Transformers

14.1 Transformer Construction & Operation 14.2 Losses, Efficiency, Load/No-Load & Turns Ratio 14.3 Three-Phase Transformers & Autotransformers

15 Filters & AC Generators

15.1 Filters — Low Pass, High Pass, Band Pass, Band Stop 15.2 AC Generator Principles & Construction 15.3 Star/Delta Connections & Permanent Magnet Generators

16 AC Motors

16.1 Synchronous & Induction Motors 16.2 Speed Control, Direction & Rotating Field Methods

16.2 Speed Control, Direction & Rotating Field Methods

Key Takeaways Explain This Topic AI

Induction-motor speed is set mainly by supply frequency and pole count (ns = 120f/P) and by slip; practical controls change f (V/f drives), poles (pole-changing), or effective slip/torque (voltage, rotor resistance on wound rotors)

Three-phase direction reverses by swapping any two supply lines; single-phase reverse methods depend on which auxiliary winding or capacitor connection is swapped

Single-phase motors need a phase-shifted auxiliary field to start — capacitor-start/run, inductor (reactor) phase shift, or shaded/split-pole construction

Shaded-pole motors are simple, low-torque starters for small fans; capacitor methods give stronger starting torque for larger single-phase loads

Aircraft technicians use these ideas for accessory motors, ground equipment, and troubleshooting wrong rotation or failed-start symptoms

Last updated: July 2026

16.2 Speed Control, Direction & Rotating Field Methods

Quick Answer: Speed ≈ follow ns = 120f/P (and slip). Change f , P , or slip-related controls. Reverse 3-phase by swapping two lines. Single-phase needs a phase-shifted second field: capacitor , inductor , or shaded/split pole .

Section 16.1 fixed what sync and induction motors are. This section answers three technician questions: How do we change speed ? How do we reverse rotation ? How do we make a rotating field when only single-phase power is available?

Speed Control — Principles Tied to ns and Slip

For an induction motor:

n = ns (1 − s) = (120 f / P) (1 − s)

So every speed-control method attacks f , P , or s (or the torque curve that sets the operating slip).

Method What you change Effect Typical notes

Frequency control (inverter / V/f drive) f (and usually V with f) ns scales with f → wide speed range Modern standard for variable-speed AC

Pole changing P (reconnect windings, e.g. 4/8 pole) ns jumps in discrete steps Dahlander / multi-speed motors

Supply voltage reduction Torque capability / slip under load Speed may fall under load; limited range Inefficient; heating risk

Wound-rotor external R Torque–slip curve Higher slip at given load for start/control Slip rings + resistor bank

Sync motor Essentially locked to f and P Speed fixed unless f or P changes Not a “soft” speed knob

Worked example 1 — frequency control. Four-pole induction motor. At 400 Hz, ns = 12 000 rev/min. If an inverter feeds 200 Hz (V reduced roughly in proportion):

ns = 120 × 200 / 4 = 6000 rev/min . With 3% slip, n ≈ 5820 rev/min — about half speed.

Worked example 2 — pole changing. Same frame, 400 Hz, reconnect from 4-pole to 8-pole:

ns₄ = 12 000; ns₈ = 120 × 400 / 8 = 6000 rev/min . Discrete half-speed field without changing f.

Worked example 3 — slip increase (wound rotor). At ns = 1500 rev/min (50 Hz, 4-pole), inserting rotor resistance might set operating point at s = 0.10 under a given load → n = 1350 rev/min. Useful for starting torque shaping; continuous high slip wastes I²R heat in the resistors.

Synchronous-motor speed control

Steady sync speed is rigidly ns = 120f/P . To vary speed you must vary supply frequency (and manage excitation) or change pole count if the design allows. You do not “add slip” for normal speed control — slip means loss of synchronism.

  • Machine Primary speed levers
  • Induction f, P, slip-related controls
  • Synchronous f and P only (while in sync)

Aircraft link. Fixed-frequency 400 Hz buses fix ns for a given pole count — accessory motors often run at essentially fixed design speed. Variable-frequency generators or dedicated inverters enable controlled-speed AC loads. Wrong frequency on a motor (ground cart mismatch, failed converter) → wrong speed and possible overheating.

  • Direction of Rotation
  • Three-phase motors

The rotating-field direction follows the phase sequence (ABC vs ACB). Reverse any two of the three supply leads → reverse sequence → reverse rotation.

  • Action Result
  • Swap L1 and L2 (leave L3) Direction reverses
  • Swap any other pair Same — reverse

Swap all three in a cycle Sequence may stay or reverse depending on permutation — exam safe answer: swap two lines

Worked concept. A hydraulic pump motor runs the wrong way after maintenance. Likely cause: two phase leads swapped at the connector. Correct by restoring original sequence — do not randomly swap until nameplates and plumbing allow safe bump-test.

Single-phase motors

Direction depends on the relative phase of the auxiliary winding (or shaded-pole geometry). Reverse by reversing the auxiliary winding leads relative to the main winding (or reversing capacitor connections per manufacturer diagram) — not by a simple “swap two of three” rule, because there are not three supply phases.

  • Motor type Typical reverse method
  • Capacitor-start / capacitor-run Reverse auxiliary (or specified) leads
  • Split-phase (resistance start) Reverse start-winding leads relative to run
  • Shaded-pole Usually not reversed in service — shading geometry is fixed; some designs are unidirectional
  • Producing a Rotating Field on Single-Phase — Why It Matters

A single main winding alone gives a pulsating field → no starting torque . Create a second magnetic axis displaced in space, fed with current displaced in time (phase), and the resultant approximates a rotating field for start (and sometimes run).

  • Requirement Meaning
  • Space displacement Auxiliary winding axis not coincident with main (often ~90° electrical)
  • Time (phase) displacement Auxiliary current not in phase with main current
  • Result Starting torque in a preferred direction
  • Capacitor Methods

A capacitor in series with the auxiliary winding advances auxiliary current (current leads voltage in a capacitive branch), creating a large phase shift relative to the main (inductive) winding.

Type Arrangement Behaviour

Capacitor-start Larger start capacitor + centrifugal or relay switch Strong start torque; capacitor switched out when up to speed

  • Capacitor-run Cap stays in circuit Better running PF/torque; quieter
  • Capacitor-start-and-run Start cap + run cap Strong start and improved run

Worked qualitative example. Main winding current lags supply voltage. Auxiliary + capacitor current leads. Phase difference approaches quadrature → effective rotating field → motor starts toward the designed direction.

Failure mode (exam/hangar). Open start capacitor or failed start switch → motor hums, draws high current, does not start → overheating. Shorted cap → wrong phase shift / blown protection.

Inductor (Reactor) Methods

An inductor (reactor) or a highly inductive auxiliary winding produces phase shift by making auxiliary current lag differently from the main winding. Classic split-phase motors use a high-resistance start winding (more resistive phase angle) rather than a large capacitor; some texts group inductive/reactive auxiliary arrangements with “inductor” phase-shift methods for Module 3.

  • Approach Phase-shift idea Starting torque
  • Capacitor in aux Strong lead of aux current Generally higher
  • Inductive / resistive split-phase Different R–L angles between windings Moderate; switch out start winding

Comparison for exams: capacitor methods usually give better starting torque than plain split-phase; inductors/reactors alone are less common today than capacitors but appear in syllabus language as a phase-shift tool.

  • Shaded Pole and Split Pole
  • Shaded-pole motor

A shading ring (copper loop) encircles part of each pole face. Induced currents in the ring delay flux in the shaded portion. The flux “sweeps” from unshaded to shaded region → weak rotating field → low starting torque, one preferred direction.

  • Trait Shaded-pole
  • Parts Salient poles, shading rings, squirrel-cage rotor
  • Starting torque Low
  • Efficiency Modest
  • Use Small fans, timers, light blowers
  • Reverse Generally not practical in the field
  • Split-pole (related idea)

Split-pole constructions divide the pole or use auxiliary magnetic paths so flux in one portion lags the other — same goal as shading: time-displaced flux across the pole arc to nudge a rotating field for start. Syllabus wording “shaded or split pole” groups these salient-pole flux-delay starters.

  • Method Space shift Time shift mechanism Typical torque
  • Capacitor aux winding Separate aux winding C phase shift High (start)
  • Inductor / split-phase Separate aux winding L / R angle difference Medium
  • Shaded / split pole Pole geometry Induced lag in ring / split path Low

Worked concept — troubleshooting. A shaded-pole cabin blower fails to start but spins freely by hand and then runs: look for seized bearings or debris first; if it never develops even a twitch of torque, shading ring damage or open winding is plausible. A capacitor-start motor with the same symptom more often has a bad capacitor or start switch.

Direction + Rotating-Field Summary Table

  • Supply How rotating field is made How to reverse
  • Three-phase Inherent 120° windings Swap two lines
  • Single-phase + capacitor Aux winding + C Reverse aux (per diagram)
  • Single-phase + inductor/split-phase Aux winding R–L shift Reverse start winding
  • Shaded / split pole Pole shading / split flux Usually fixed direction
  • Section Synthesis

Speed follows n = (120f/P)(1 − s) — control f, P, or slip-related means.

Reverse three-phase by two-line swap ; single-phase by auxiliary/capacitor lead reversal.

Capacitor, inductor/split-phase, and shaded/split-pole methods all create time-shifted flux for starting torque.

Match symptom to method: failed start capacitor vs inherently weak shaded-pole torque.

Topic 3.18 closes Module 3’s rotating-machine story: generators made the rotating field; motors use it — with slip, sync lock, and single-phase starting tricks every CAAS SAR-66 candidate must recognise.