Study guide

12.1 Sinusoidal Waveforms — Phase, Period, Frequency

CAAS SAR-66 AML Module 3 — Electrical Fundamentals Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Knowledge Levels & Study Approach for Module 3

2 Electron Theory & Static Electricity

2.1 Electron Theory & Atomic Structure 2.2 Conductors, Semiconductors & Insulators 2.3 Static Electricity, Coulomb's Law & Conduction

3 Terminology & Generation of Electricity

3.1 Electrical Terminology 3.2 Generation of Electricity

4 DC Sources of Electricity

4.1 Primary & Secondary Cells 4.2 Lead-Acid & Nickel-Cadmium Batteries 4.3 Series/Parallel Cells, Internal Resistance, Thermocouples & Photocells

5 DC Circuits

5.1 Ohm's Law 5.2 Kirchhoff's Voltage & Current Laws 5.3 Series/Parallel Networks & Supply Internal Resistance

6 Resistance & Resistors

6.1 Resistivity & Factors Affecting Resistance 6.2 Resistor Colour Code, Tolerance & Preferred Values 6.3 Series/Parallel Resistors, Potentiometers & Rheostats 6.4 Wheatstone Bridge, Thermistors & Temperature Coefficient

7 Power, Work & Energy

7.1 Power, Work & Energy Concepts 7.2 Power Dissipation & Calculations

8 Capacitance & Capacitors

8.1 Capacitor Operation & Factors Affecting Capacitance 8.2 Series/Parallel Capacitors & Types 8.3 RC Time Constants, Energy Storage & Testing

9 Magnetism

9.1 Theory of Magnetism & Magnetic Materials 9.2 Electromagnets & Hand Rules 9.3 MMF, Flux Density, Permeability, Hysteresis & Eddy Currents

10 Inductance & Inductors

10.1 Faraday's Law & Induced Voltage 10.2 Self & Mutual Inductance, Lenz's Law 10.3 Back EMF, Saturation & Inductor Applications

11 DC Motor/Generator Theory

11.1 Basic Motor & Generator Theory 11.2 DC Generators — Construction & Operation 11.3 DC Motors — Series, Shunt, Compound & Starter-Generators

12 AC Theory

12.1 Sinusoidal Waveforms — Phase, Period, Frequency 12.2 Peak, Average, RMS Values & Calculations 12.3 Non-Sinusoidal Waves & Single/Three-Phase Principles

13 R, L & C Circuits

13.1 Phase Relationships in R, L, C Circuits 13.2 Impedance, Phase Angle & Power Factor 13.3 True, Apparent & Reactive Power

14 Transformers

14.1 Transformer Construction & Operation 14.2 Losses, Efficiency, Load/No-Load & Turns Ratio 14.3 Three-Phase Transformers & Autotransformers

15 Filters & AC Generators

15.1 Filters — Low Pass, High Pass, Band Pass, Band Stop 15.2 AC Generator Principles & Construction 15.3 Star/Delta Connections & Permanent Magnet Generators

16 AC Motors

16.1 Synchronous & Induction Motors 16.2 Speed Control, Direction & Rotating Field Methods

12.1 Sinusoidal Waveforms — Phase, Period, Frequency

Key Takeaways Explain This Topic AI

One AC cycle is one complete 360° (2π radian) variation of the sinusoidal waveform from a chosen starting point back to the same condition with the same direction of change

Period T is the time for one cycle; frequency f = 1/T, with f in hertz (Hz) when T is in seconds

Instantaneous sine voltage is v = V_peak sin(ωt + φ) where ω = 2πf and φ is the phase angle in radians (or degrees when the stem uses degrees)

Phase difference compares two waveforms of the same frequency; lead means the reference point occurs earlier in time, lag means later

Aircraft AC power is commonly 115 V RMS at 400 Hz — higher frequency than utility 50/60 Hz so transformers and machines can be lighter for the same power

Last updated: July 2026

12.1 Sinusoidal Waveforms — Phase, Period, Frequency

Quick Answer: A sinusoidal AC quantity repeats in cycles . Period T is the time for one cycle; frequency f = 1/T . Instantaneous value follows v = V_peak sin(ωt + φ) with ω = 2πf . Phase locates the sine relative to a time origin; phase difference compares two same-frequency waves (lead/lag). Aircraft AC is typically 115 V RMS at 400 Hz .

CAAS SAR-66 Module 3 topic 3.13 AC theory follows DC machines (3.12) and precedes R, L, and C circuits (3.14). Everything later—reactance, power factor, transformers, and AC generators—assumes you can read a sine wave: how often it repeats, where it sits in time, and what “in phase” means. This section builds that language.

Why AC Is Drawn as a Sine Wave

In a simple AC generator, a coil rotates at constant speed in a uniform magnetic field. The induced EMF is proportional to the rate of flux cutting. For constant rotation in a uniform field, that rate varies as the sine (or cosine) of the rotor angle. Plotting induced voltage against time therefore yields a sinusoidal waveform —the ideal shape assumed in Module 3 unless a stem specifies otherwise.

A sine wave is completely described by:

Amplitude (peak value) — how tall the wave is.

Frequency (or period) — how fast it repeats.

Phase — where the wave sits relative to t = 0 or to another wave.

Amplitude arithmetic (peak, RMS, average) is Section 12.2. Here the focus is time and phase.

  • Cycle, Period, and Frequency
  • Cycle

One cycle is one complete pattern of the waveform that returns to the same value and the same direction of change. For a sine starting at zero going positive:

  • 0° → rising through zero
  • 90° → positive peak
  • 180° → falling through zero
  • 270° → negative peak
  • 360° → back to zero rising again — one cycle complete

Angles may be stated in degrees (0° to 360°) or radians (0 to 2π). One cycle = 360° = 2π rad .

Period (T)

Period T is the time duration of one cycle. SI unit: second (s) . On an oscilloscope, T is the horizontal distance for one full repetition multiplied by the time/division setting.

Frequency (f)

Frequency f is the number of cycles per second:

f = 1 / T

  • Quantity Symbol SI unit Meaning
  • Period T s Time per cycle
  • Frequency f hertz (Hz) Cycles per second
  • Angular frequency ω rad/s ω = 2πf

Worked example 1 — period from frequency. Aircraft AC at f = 400 Hz :

T = 1 / 400 = 0.0025 s = 2.5 ms .

Worked example 2 — frequency from period. A sine wave has T = 20 ms = 0.020 s.

f = 1 / 0.020 = 50 Hz (utility frequency in many regions).

Worked example 3 — compare times. At 60 Hz, T = 1/60 ≈ 16.7 ms . At 400 Hz, T = 2.5 ms . The aircraft wave completes a cycle about 6.7 times faster than a 60 Hz utility wave (400/60 ≈ 6.67).

Angular frequency

ω = 2πf converts frequency into radians per second—the natural rate used inside the sine argument.

At 400 Hz: ω = 2π × 400 = 800π rad/s ≈ 2513 rad/s .

At 50 Hz: ω = 2π × 50 = 100π rad/s ≈ 314 rad/s .

Module 3 rarely asks you to compute ω numerically, but you must recognise that ωt advances one full cycle when ωt increases by 2π.

Instantaneous Sinusoidal Expression

For a sinusoidal voltage:

v = V_m sin(ωt + φ)

  • Symbol Meaning
  • v Instantaneous voltage at time t
  • V_m (or V_peak) Maximum (peak) voltage
  • ω Angular frequency = 2πf
  • t Time from the chosen origin
  • φ Phase angle at t = 0

Current uses the same form: i = I_m sin(ωt + φ_i) .

Special cases:

If φ = 0 and the sine starts at the origin: v = V_m sin(ωt).

If the wave is a cosine at the origin: v = V_m cos(ωt) = V_m sin(ωt + 90°), because cos θ = sin(θ + 90°).

Worked example 4 — instantaneous value. V_m = 170 V, f = 400 Hz, φ = 0. Find v at t = 0.625 ms.

ωt = 2π × 400 × 0.000625 = 2π × 0.25 = π/2 rad = 90° .

v = 170 sin(90°) = 170 V (positive peak).

Worked example 5 — zero crossings. Same wave, zeros when sin(ωt) = 0 → ωt = 0°, 180°, 360°, … Positive-going zero at the start of each cycle; negative-going zero at mid-cycle.

  • Phase and Phase Difference
  • Phase of one waveform

Phase answers: where is the sine relative to the time origin? The constant φ shifts the whole wave left or right without changing frequency or amplitude.

φ > 0 (with the +φ convention above) advances the argument — the wave reaches a given point earlier than the φ = 0 reference (often called a leading phase for that single-wave description).

φ < 0 delays the wave — it lags the φ = 0 reference.

Always read the stem’s sign convention. Some texts write v = V_m sin(ωt − φ) with φ defined as a lag angle. The physics is the same; the algebra must match the formula given.

Phase difference between two waveforms

Maintenance and Module 3 care most about phase difference —the constant angular gap between two same-frequency sinusoids (for example voltage and current in an AC circuit, or two phase voltages of a generator).

  • If
  • v = V_m sin(ωt)
  • i = I_m sin(ωt − θ)

then current lags voltage by angle θ (common inductive case). If i = I_m sin(ωt + θ), current leads voltage by θ (common capacitive case).

  • Description Meaning in time
  • In phase Peaks and zero-crossings occur together (θ = 0°)
  • Lead The leading wave reaches its peak earlier
  • Lag The lagging wave reaches its peak later
  • Quadrature 90° apart
  • Opposition 180° apart (inverted relative timing)

Time shift linked to phase: For frequency f, a phase difference of θ degrees corresponds to a time shift:

Δt = (θ / 360°) × T = θ / (360° × f)

Worked example 6 — time from phase. At 400 Hz, T = 2.5 ms. A current lags voltage by 90°.

Δt = (90/360) × 2.5 ms = 0.625 ms .

Worked example 7 — phase from time. Two 50 Hz voltages; wave B peaks 5 ms after wave A.

T = 20 ms. Fraction of cycle = 5/20 = 0.25 → phase lag of B behind A = 90° .

Aircraft Context: 115 V, 400 Hz

Large civil aircraft commonly distribute 115 V AC (RMS line-to-neutral on many systems) at 400 Hz . Why 400 Hz rather than 50 or 60 Hz?

Factor Effect of higher frequency

Transformer core / winding size For a given power and flux density limit, higher f allows smaller, lighter magnetics

  • AC motor / generator size Similar mass–power benefit in rotating machines
  • Period Only 2.5 ms per cycle — instruments and converters must handle faster AC

Reactance X_L = 2πfL is larger at 400 Hz than at 50 Hz for the same L; X_C = 1/(2πfC) is smaller — critical in later RLC topics

Module 3 will not ask you to design a 400 Hz generator here, but using 400 Hz in period and phase-shift calculations is a standard exam habit. Ground utility power (50/60 Hz) is a different frequency world—do not mix periods.

Many training stems also quote 28 V DC for DC buses. Keep the two systems mentally separate: DC has no frequency; aircraft AC almost always implies f = 400 Hz unless the question says otherwise.

Reading Waveforms on Paper or Scope

Exam diagrams often show two sine waves on one time axis. Method:

Confirm both have the same period (same frequency). Phase difference is undefined in the simple constant sense if frequencies differ.

Pick a clear reference event (for example positive-going zero or positive peak) on wave A.

Measure how far wave B’s corresponding event is to the right (later → lag) or left (earlier → lead).

Convert the horizontal fraction of one period into degrees: fraction × 360°.

Amplitude on the vertical axis is independent of phase. A small wave can lead a large wave; lead/lag is about timing, not height.

Summary Table for Syllabus 3.13 Time Vocabulary

  • Term Definition Key relation
  • Cycle One full 360° repetition —
  • Period T Time per cycle T = 1/f
  • Frequency f Cycles per second f = 1/T
  • Angular frequency ω Radians per second ω = 2πf
  • Phase φ Shift of one wave vs time origin in v = V_m sin(ωt + φ)
  • Phase difference Constant angle between two same-f waves Δt = (θ/360°)T

Master cycle ↔ T ↔ f, the sine expression, and lead/lag from diagrams. Section 12.2 then converts the vertical scale of the same sine into peak, average, and RMS values used on every aircraft AC nameplate.