Study guide

8.1 Capacitor Operation & Factors Affecting Capacitance

CAAS SAR-66 AML Module 3 — Electrical Fundamentals Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Knowledge Levels & Study Approach for Module 3

2 Electron Theory & Static Electricity

2.1 Electron Theory & Atomic Structure 2.2 Conductors, Semiconductors & Insulators 2.3 Static Electricity, Coulomb's Law & Conduction

3 Terminology & Generation of Electricity

3.1 Electrical Terminology 3.2 Generation of Electricity

4 DC Sources of Electricity

4.1 Primary & Secondary Cells 4.2 Lead-Acid & Nickel-Cadmium Batteries 4.3 Series/Parallel Cells, Internal Resistance, Thermocouples & Photocells

5 DC Circuits

5.1 Ohm's Law 5.2 Kirchhoff's Voltage & Current Laws 5.3 Series/Parallel Networks & Supply Internal Resistance

6 Resistance & Resistors

6.1 Resistivity & Factors Affecting Resistance 6.2 Resistor Colour Code, Tolerance & Preferred Values 6.3 Series/Parallel Resistors, Potentiometers & Rheostats 6.4 Wheatstone Bridge, Thermistors & Temperature Coefficient

7 Power, Work & Energy

7.1 Power, Work & Energy Concepts 7.2 Power Dissipation & Calculations

8 Capacitance & Capacitors

8.1 Capacitor Operation & Factors Affecting Capacitance 8.2 Series/Parallel Capacitors & Types 8.3 RC Time Constants, Energy Storage & Testing

9 Magnetism

9.1 Theory of Magnetism & Magnetic Materials 9.2 Electromagnets & Hand Rules 9.3 MMF, Flux Density, Permeability, Hysteresis & Eddy Currents

10 Inductance & Inductors

10.1 Faraday's Law & Induced Voltage 10.2 Self & Mutual Inductance, Lenz's Law 10.3 Back EMF, Saturation & Inductor Applications

11 DC Motor/Generator Theory

11.1 Basic Motor & Generator Theory 11.2 DC Generators — Construction & Operation 11.3 DC Motors — Series, Shunt, Compound & Starter-Generators

12 AC Theory

12.1 Sinusoidal Waveforms — Phase, Period, Frequency 12.2 Peak, Average, RMS Values & Calculations 12.3 Non-Sinusoidal Waves & Single/Three-Phase Principles

13 R, L & C Circuits

13.1 Phase Relationships in R, L, C Circuits 13.2 Impedance, Phase Angle & Power Factor 13.3 True, Apparent & Reactive Power

14 Transformers

14.1 Transformer Construction & Operation 14.2 Losses, Efficiency, Load/No-Load & Turns Ratio 14.3 Three-Phase Transformers & Autotransformers

15 Filters & AC Generators

15.1 Filters — Low Pass, High Pass, Band Pass, Band Stop 15.2 AC Generator Principles & Construction 15.3 Star/Delta Connections & Permanent Magnet Generators

16 AC Motors

16.1 Synchronous & Induction Motors 16.2 Speed Control, Direction & Rotating Field Methods

8.1 Capacitor Operation & Factors Affecting Capacitance

Key Takeaways Explain This Topic AI

Capacitance is defined by C = Q/V: the charge stored per volt of potential difference between the plates

Farads are the SI unit; Module 3 work normally uses µF, nF, and pF because one farad is enormous for practical parts

For a parallel-plate capacitor, C rises with plate area and dielectric constant, and falls as plate separation increases

Adding plates in a multi-plate stack increases effective capacitance approximately with the number of dielectric gaps

Working voltage (voltage rating) must never be exceeded — dielectric breakdown can short, open, or destroy the capacitor

Last updated: July 2026

8.1 Capacitor Operation & Factors Affecting Capacitance

Quick Answer: A capacitor stores charge on two conductors separated by an insulator (dielectric). C = Q / V , so capacitance is charge stored per volt. Increase plate area or dielectric constant , or add more plates, and C rises; increase plate separation and C falls. Always stay below the marked working voltage .

CAAS SAR-66 Module 3 topic 3.9 Capacitance / capacitor sits between resistance and magnetism in the electrical fundamentals syllabus. Aircraft systems use capacitors for filtering, timing, coupling, and energy storage on DC buses and AC equipment. Before you combine capacitors in series or parallel, you must understand what one capacitor is and what changes its farad value.

What a Capacitor Does

A basic capacitor has:

Two conductive plates (or foils, films, or electrodes).

A dielectric — an insulating material between the plates (air, paper, mica, ceramic, plastic film, oxide layer, and so on).

When a DC voltage is applied, electrons are driven onto one plate and removed from the other. Opposite charges accumulate. The dielectric prevents a continuous DC conduction path (ideally), so after the transient charging current dies, steady DC current through an ideal capacitor is zero . The stored electrostatic field holds the charge until the circuit discharges it through a path.

Charge polarity: The plate connected toward the more negative supply accumulates excess electrons (negative charge). The other plate is deficient in electrons (positive charge). The magnitude of charge on each plate is the same; we call that magnitude Q .

Definition: C = Q / V

Capacitance C is defined as:

C = Q / V

  • Symbol Meaning SI unit
  • C Capacitance farad (F)
  • Q Magnitude of charge on either plate coulomb (C)
  • V Potential difference between plates volt (V)

Rearrangements you must use fluently:

  • Q = C × V
  • V = Q / C

Physical reading: A 1 F capacitor would store 1 C of charge at 1 V. Practical capacitors are tiny fractions of a farad, so Module 3 uses submultiples:

  • Unit Relation to farads Typical use
  • microfarad (µF) 1 µF = 10⁻⁶ F Power supply filters, large timing
  • nanofarad (nF) 1 nF = 10⁻⁹ F Coupling, RF, intermediate values
  • picofarad (pF) 1 pF = 10⁻¹² F High-frequency, small trimmers

Worked example 1 — find C. A capacitor holds Q = 200 µC at V = 50 V .

Convert: Q = 200 × 10⁻⁶ C = 2.0 × 10⁻⁴ C.

C = Q / V = (2.0 × 10⁻⁴) / 50 = 4.0 × 10⁻⁶ F = 4 µF .

Worked example 2 — find charge. A 10 µF capacitor is charged to 28 V (aircraft DC bus order of magnitude).

Q = C × V = 10 × 10⁻⁶ × 28 = 2.8 × 10⁻⁴ C = 280 µC .

Worked example 3 — find voltage. A 0.47 µF capacitor stores 94 µC .

V = Q / C = (94 × 10⁻⁶) / (0.47 × 10⁻⁶) = 200 V .

Unit discipline matters: mixing µC with F without converting produces nonsense voltages. Convert both Q and C to coulombs and farads, or keep consistent micro-units carefully (µC / µF = V).

Parallel-Plate Factors Affecting Capacitance

For a simple parallel-plate capacitor in SI form:

C = ε₀ εᵣ A / d

  • Symbol Meaning
  • ε₀ Permittivity of free space (constant)
  • εᵣ Relative permittivity / dielectric constant of the insulator
  • A Overlapping plate area
  • d Separation (dielectric thickness) between plates

You rarely need the numerical value of ε₀ on Module 3. You do need the proportional rules:

  • If this increases (others fixed)… Effect on C
  • Plate area A C increases (directly proportional)
  • Plate separation d C decreases (inversely proportional)
  • Dielectric constant εᵣ C increases (directly proportional)
  • Number of plates (multi-plate stack) C increases (more gaps / effective area)
  • Area

Larger overlapping area → more charge can be stored at the same voltage → higher C. Doubling A doubles C.

Worked example 4 — area. A capacitor has C₁ = 100 pF. Plate overlap area is doubled; d and dielectric unchanged. New C = 200 pF .

Distance (separation)

Smaller gap → stronger field for a given V and more charge for that V → higher C. Doubling d halves C. Pushing plates closer raises C until dielectric strength or mechanical limits intervene.

Worked example 5 — separation. C₁ = 0.22 µF. Separation is reduced to one-third. New C = 0.22 × 3 = 0.66 µF .

Dielectric constant

Replacing air (εᵣ ≈ 1) with a material of εᵣ = 5 multiplies C by about 5 , same geometry. Higher-εᵣ dielectrics pack more capacitance into a smaller package — why ceramics and specialised films appear in avionics boards.

Worked example 6 — dielectric swap. An air-spaced capacitor is 50 pF. Insert a dielectric with εᵣ = 4 (same A and d). New C ≈ 200 pF .

Number of plates

Multi-plate capacitors interleave several plates with dielectric between each adjacent pair. Each facing pair forms a capacitor; the sections act in parallel, so total C rises with the number of dielectric gaps (roughly C ∝ (n − 1) for n interleaved plates of equal area, same d).

Exam phrasing: “Increasing the number of plates increases capacitance” is the Module 3 statement to remember, alongside area up / distance down / dielectric constant up.

Working Voltage / Voltage Rating

Every capacitor has a working voltage (WV), DC working voltage (WVDC), or similar voltage rating . This is the maximum continuous voltage the manufacturer rates the dielectric to withstand under stated conditions.

Exceeding the rating risks dielectric breakdown : the insulator punches through, the capacitor may short, open, leak heavily, or fail violently (especially electrolytics).

Always select a rating above the highest voltage the capacitor will see, including spikes and AC peaks where relevant.

On a 28 V DC aircraft bus filter, a 16 V capacitor is unsafe; a 35 V or 50 V part is the usual thinking — rating must clear the actual voltage with margin.

Worked example 7 — rating check. A timing capacitor sits across a 24 V DC rail that can surge to 30 V. A part marked 25 V WVDC is inadequate for the surge; choose ≥ 35 V (or the design minimum specified).

Capacitance value and voltage rating are independent markings . A 10 µF / 16 V part and a 10 µF / 63 V part store the same charge at 10 V, but only the higher-rated part survives higher applied voltage.

Charge, Voltage, and Current Behaviour (Preview)

While charging from a DC source through resistance, current flows until V_capacitor equals the applied voltage (ideal case). Once charged and open-circuited, an ideal capacitor holds Q; real parts slowly leak. Connecting a charged capacitor across a low resistance produces a discharge current — energy leaves the electrostatic field as heat and/or work. Section 8.3 develops the RC time constant and energy ½CV² ; here the exam core is C = Q/V plus the four construction factors and voltage rating.

Factor Summary for Module 3

  • Factor Direction that increases C
  • Plate area Larger area
  • Plate distance Smaller separation
  • Dielectric constant Higher εᵣ
  • Number of plates More plates / more gaps
  • Applied voltage Does not change C (ideal); it changes Q = CV

Trap: Raising voltage stores more charge (Q = CV) but does not redefine the capacitance of a linear capacitor. C is the constant of proportionality, not something that “grows” because you applied more volts (within the linear, undamaged range).

Master C = Q/V , the µF/nF/pF conversions, the area–distance–dielectric–plates rules, and working-voltage discipline. Those tools unlock series/parallel networks and RC timing in the next sections.