Study guide

5.1 Ohm's Law

CAAS SAR-66 AML Module 3 — Electrical Fundamentals Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Knowledge Levels & Study Approach for Module 3

2 Electron Theory & Static Electricity

2.1 Electron Theory & Atomic Structure 2.2 Conductors, Semiconductors & Insulators 2.3 Static Electricity, Coulomb's Law & Conduction

3 Terminology & Generation of Electricity

3.1 Electrical Terminology 3.2 Generation of Electricity

4 DC Sources of Electricity

4.1 Primary & Secondary Cells 4.2 Lead-Acid & Nickel-Cadmium Batteries 4.3 Series/Parallel Cells, Internal Resistance, Thermocouples & Photocells

5 DC Circuits

5.1 Ohm's Law 5.2 Kirchhoff's Voltage & Current Laws 5.3 Series/Parallel Networks & Supply Internal Resistance

6 Resistance & Resistors

6.1 Resistivity & Factors Affecting Resistance 6.2 Resistor Colour Code, Tolerance & Preferred Values 6.3 Series/Parallel Resistors, Potentiometers & Rheostats 6.4 Wheatstone Bridge, Thermistors & Temperature Coefficient

7 Power, Work & Energy

7.1 Power, Work & Energy Concepts 7.2 Power Dissipation & Calculations

8 Capacitance & Capacitors

8.1 Capacitor Operation & Factors Affecting Capacitance 8.2 Series/Parallel Capacitors & Types 8.3 RC Time Constants, Energy Storage & Testing

9 Magnetism

9.1 Theory of Magnetism & Magnetic Materials 9.2 Electromagnets & Hand Rules 9.3 MMF, Flux Density, Permeability, Hysteresis & Eddy Currents

10 Inductance & Inductors

10.1 Faraday's Law & Induced Voltage 10.2 Self & Mutual Inductance, Lenz's Law 10.3 Back EMF, Saturation & Inductor Applications

11 DC Motor/Generator Theory

11.1 Basic Motor & Generator Theory 11.2 DC Generators — Construction & Operation 11.3 DC Motors — Series, Shunt, Compound & Starter-Generators

12 AC Theory

12.1 Sinusoidal Waveforms — Phase, Period, Frequency 12.2 Peak, Average, RMS Values & Calculations 12.3 Non-Sinusoidal Waves & Single/Three-Phase Principles

13 R, L & C Circuits

13.1 Phase Relationships in R, L, C Circuits 13.2 Impedance, Phase Angle & Power Factor 13.3 True, Apparent & Reactive Power

14 Transformers

14.1 Transformer Construction & Operation 14.2 Losses, Efficiency, Load/No-Load & Turns Ratio 14.3 Three-Phase Transformers & Autotransformers

15 Filters & AC Generators

15.1 Filters — Low Pass, High Pass, Band Pass, Band Stop 15.2 AC Generator Principles & Construction 15.3 Star/Delta Connections & Permanent Magnet Generators

16 AC Motors

16.1 Synchronous & Induction Motors 16.2 Speed Control, Direction & Rotating Field Methods

5.1 Ohm's Law

Key Takeaways Explain This Topic AI

Ohm’s law states V = IR; rearrange to I = V/R and R = V/I for any two known quantities

Keep SI units consistent (volts, amperes, ohms)—convert mA, kΩ, and mV before substituting

For a fixed resistance, I is proportional to V; for a fixed voltage, I is inversely proportional to R

Proportional-reasoning traps include assuming doubling both V and R doubles I, or treating power relationships as Ohm’s law

  • Aircraft sanity checks (for example 28 V DC buses) catch decimal and unit errors before you commit an answer
  • Last updated: July 2026

5.1 Ohm's Law

Quick Answer: For a resistive DC element, V = I × R . Solve for current with I = V / R and for resistance with R = V / I . Convert every quantity to volts, amperes, and ohms before you multiply or divide, then sense-check the magnitude against typical aircraft values such as a 28 V DC bus.

Ohm’s law is the calculation backbone of CAAS SAR-66 Module 3 topic 3.6 DC Circuits . Almost every later network problem—series strings, parallel branches, voltage dividers, and internal-resistance loading—starts by applying V = IR to one element or to an equivalent resistance. If this relationship is automatic, Kirchhoff and combination circuits become bookkeeping. If it is shaky, the rest of Module 3 collapses under time pressure.

The Three Forms

  • Known quantities Find Formula
  • I and R Voltage V V = I × R
  • V and R Current I I = V / R
  • V and I Resistance R R = V / I

These three forms are algebraically identical. On the exam, choose the form that isolates the unknown in one step. Do not rearrange under stress if the printed form already matches the stem.

Physical meaning: For a metallic conductor at constant temperature, current is proportional to the applied potential difference. Doubling V at fixed R doubles I. Doubling R at fixed V halves I. Resistance is the constant of proportionality: R = V/I .

Unit Discipline (Where Marks Are Lost)

Module 3 stems freely mix prefixes:

  • Given Convert to SI base before Ohm’s law
  • 250 mA 0.25 A
  • 48 mV 0.048 V
  • 4.7 kΩ 4700 Ω
  • 2.2 MΩ 2.2 × 10⁶ Ω

Rule: Convert first, calculate second, then optionally convert the answer back to the unit the options use. Mixing 28 V with 100 mA without converting yields a “resistance” of 0.28 Ω when the true value is 280 Ω .

Worked Example 1 — Find Current

A landing-light control resistor of 14 Ω is connected across a 28 V DC bus (ideal source for this item).

I = V / R = 28 / 14 = 2 A .

Sanity check: 28 V and a low double-digit ohm value should produce amperes, not milliamperes. If your calculator shows 0.002 A, you likely treated 28 as millivolts or 14 as kilohms.

Worked Example 2 — Find Voltage Drop

A feeder carries 15 A through a total cable-plus-joint resistance of 0.08 Ω .

V = I × R = 15 × 0.08 = 1.2 V .

The bus may still be near 28 V at the source, but the load end is 1.2 V lower because of that feeder drop. Ohm’s law applies to any resistive segment, not only to the named load.

Worked Example 3 — Find Resistance

A heater draws 3.5 A from a 115 V DC shop supply (DC for this practice item).

R = V / I = 115 / 3.5 ≈ 32.86 Ω (about 33 Ω if options are rounded).

If options include 32.9 Ω , 0.030 Ω , and 402.5 Ω , reject inverted V/I or I×V mistakes immediately.

Worked Example 4 — Mixed Prefixes

A sensor sees 24 V across 4.7 kΩ .

Convert: R = 4700 Ω.

I = 24 / 4700 ≈ 0.00511 A = 5.11 mA .

Exam options often list milliamperes. Leaving the answer as 0.00511 A is correct but may not match the printed choice format—read the units on each option.

Worked Example 5 — Two-Step with Partial Data

A series string has total R_T = 120 Ω on a 24 V supply. What is the current, and what voltage appears across a 40 Ω portion of that string?

I = V / R_T = 24 / 120 = 0.2 A (same current through every series element).

V_40 = I × 40 = 0.2 × 40 = 8 V .

You did not need a separate law for the second step—Ohm’s law on the segment after finding the series current.

  • Proportional Reasoning (Exam Traps)
  • Trap 1 — Doubling V and R

If V doubles and R doubles, I is unchanged because I = V/R. Candidates who “feel” that more voltage means more current, while forgetting the matching resistance change, pick “I doubles.”

Trap 2 — Inverse vs Direct

At fixed V, if R is reduced to one-third, I becomes three times larger—not one-third. Inverse proportion means the product I × R stays equal to V.

Trap 3 — Confusing Ohm with Power

Power P = VI = I²R = V²/R is related but not a substitute for Ohm’s law. A stem that gives only P and V still needs I = P/V or R = V²/P before you talk about “Ohm.” Do not invent V = P × R .

Trap 4 — Parallel intuition on a single resistor

Ohm’s law on one resistor does not care about other branches until you have found the voltage across that resistor. Applying supply voltage to a branch that is not actually at supply potential (for example, a resistor mid-string) produces wrong current.

  • Situation Correct proportional statement
  • R fixed, V × 2 I × 2
  • V fixed, R × 2 I × ½
  • V × 2 and R × 2 I unchanged
  • V fixed, R × ½ I × 2
  • Aircraft Context as a Sanity Check

Many large-aircraft DC systems centre on roughly 28 V distribution. If a simple Ohm’s-law item about a bus-powered lamp returns 2800 V or 0.0028 V , you misplaced a decimal or a kilo prefix. Use context to catch errors; do not replace the formula with “it must be 28 V” when the stem gives different numbers.

Method Checklist for Module 3

Underline the unknown (V, I, or R).

Convert all given values to V, A, Ω.

Select V = IR , I = V/R , or R = V/I .

Substitute and calculate.

Convert the result to the option’s unit if needed.

Sense-check magnitude and reject inverted formulae.

Master these six steps until they take under fifteen seconds. Topic 3.6 then becomes Kirchhoff and network topology on top of a reliable Ohm engine—not three separate subjects fighting for working memory.