Study guide

4.3 Series/Parallel Cells, Internal Resistance, Thermocouples & Photocells

CAAS SAR-66 AML Module 3 — Electrical Fundamentals Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Knowledge Levels & Study Approach for Module 3

2 Electron Theory & Static Electricity

2.1 Electron Theory & Atomic Structure 2.2 Conductors, Semiconductors & Insulators 2.3 Static Electricity, Coulomb's Law & Conduction

3 Terminology & Generation of Electricity

3.1 Electrical Terminology 3.2 Generation of Electricity

4 DC Sources of Electricity

4.1 Primary & Secondary Cells 4.2 Lead-Acid & Nickel-Cadmium Batteries 4.3 Series/Parallel Cells, Internal Resistance, Thermocouples & Photocells

5 DC Circuits

5.1 Ohm's Law 5.2 Kirchhoff's Voltage & Current Laws 5.3 Series/Parallel Networks & Supply Internal Resistance

6 Resistance & Resistors

6.1 Resistivity & Factors Affecting Resistance 6.2 Resistor Colour Code, Tolerance & Preferred Values 6.3 Series/Parallel Resistors, Potentiometers & Rheostats 6.4 Wheatstone Bridge, Thermistors & Temperature Coefficient

7 Power, Work & Energy

7.1 Power, Work & Energy Concepts 7.2 Power Dissipation & Calculations

8 Capacitance & Capacitors

8.1 Capacitor Operation & Factors Affecting Capacitance 8.2 Series/Parallel Capacitors & Types 8.3 RC Time Constants, Energy Storage & Testing

9 Magnetism

9.1 Theory of Magnetism & Magnetic Materials 9.2 Electromagnets & Hand Rules 9.3 MMF, Flux Density, Permeability, Hysteresis & Eddy Currents

10 Inductance & Inductors

10.1 Faraday's Law & Induced Voltage 10.2 Self & Mutual Inductance, Lenz's Law 10.3 Back EMF, Saturation & Inductor Applications

11 DC Motor/Generator Theory

11.1 Basic Motor & Generator Theory 11.2 DC Generators — Construction & Operation 11.3 DC Motors — Series, Shunt, Compound & Starter-Generators

12 AC Theory

12.1 Sinusoidal Waveforms — Phase, Period, Frequency 12.2 Peak, Average, RMS Values & Calculations 12.3 Non-Sinusoidal Waves & Single/Three-Phase Principles

13 R, L & C Circuits

13.1 Phase Relationships in R, L, C Circuits 13.2 Impedance, Phase Angle & Power Factor 13.3 True, Apparent & Reactive Power

14 Transformers

14.1 Transformer Construction & Operation 14.2 Losses, Efficiency, Load/No-Load & Turns Ratio 14.3 Three-Phase Transformers & Autotransformers

15 Filters & AC Generators

15.1 Filters — Low Pass, High Pass, Band Pass, Band Stop 15.2 AC Generator Principles & Construction 15.3 Star/Delta Connections & Permanent Magnet Generators

16 AC Motors

16.1 Synchronous & Induction Motors 16.2 Speed Control, Direction & Rotating Field Methods

4.3 Series/Parallel Cells, Internal Resistance, Thermocouples & Photocells

Key Takeaways Explain This Topic AI

Series connection adds cell voltages while capacity (Ah) stays that of one cell (same current through each)

Parallel connection keeps voltage (matched cells) while ampere-hour capacity and current capability add

Terminal voltage under load is V_terminal = E − I × r_internal; higher internal resistance or higher current increases voltage sag

A thermocouple generates EMF from the Seebeck effect at a junction of two dissimilar metals when heated; materials and temperature difference set the output

A photocell converts light into electrical behaviour (voltage/current) via photoelectric action—used for light sensing, not bulk aircraft power

Last updated: July 2026

4.3 Series/Parallel Cells, Internal Resistance, Thermocouples & Photocells

Quick Answer: Series cells add voltage ; Ah stays the same . Parallel matched cells keep voltage ; Ah adds . Loaded terminal voltage falls by I × r_internal . Thermocouples make a small EMF from heat at a dissimilar-metal junction; photocells respond to light. Neither replaces the aircraft battery for bulk energy.

Topic 3.5 closes by asking you to combine cells correctly, predict voltage sag from internal resistance, and recognise two important non-battery DC transducers: thermocouples and photocells. These ideas feed later DC-circuit work (topic 3.6) and appear directly on Module 3 MCQs.

Series Connection of Cells

Cells in series are connected positive-to-negative in a chain so the same current passes through every cell.

Rules (identical cells)

Total EMF / voltage: E_total = E₁ + E₂ + … + Eₙ (voltages add).

Capacity (Ah): remains approximately the Ah of one cell (they all carry the same current for the same time).

Internal resistances: add: r_total = r₁ + r₂ + … + rₙ .

Worked example — series voltage and Ah

Four identical cells, each E = 1.5 V , capacity 2 Ah , are connected in series.

  • E_total = 1.5 × 4 = 6.0 V
  • Capacity = 2 Ah (not 8 Ah)

Aircraft link: twelve lead-acid cells of ~2 V in series → ~24 V battery; twenty Ni–Cd cells of ~1.2 V in series → ~24 V battery. Series is how we reach bus voltage.

Polarity warning

If one cell is inserted reverse in a series string, it subtracts its EMF and may be driven into damaging reverse charge when current flows. Series strings demand correct polarity and reasonably matched cells.

Parallel Connection of Cells

Cells in parallel have like terminals connected together: all positives joined, all negatives joined.

Rules (identical, equal-voltage cells)

Voltage: remains approximately one cell’s voltage ( E_total ≈ E_cell ).

Capacity (Ah): adds — Ah_total = Ah₁ + Ah₂ + …

Current capability: increases because load current can split among branches.

Internal resistances: combine in parallel (effective r falls if identical cells share load).

Worked example — parallel voltage and Ah

Three identical cells, each 12 V , 40 Ah , connected in parallel:

  • Voltage ≈ 12 V
  • Capacity ≈ 40 + 40 + 40 = 120 Ah
  • Worked example — series–parallel mix

You need 24 V and higher capacity than one series string. Build two series strings of lead-acid cells for 24 V, then parallel the strings:

  • Each string: 12 × 2 V = 24 V , say 40 Ah
  • Two strings in parallel: 24 V , 80 Ah

Series sets voltage; parallel sets Ah. Mixing unequal voltages in parallel causes circulating currents—Module 3 expects matched cells.

Comparison Table: Series vs Parallel

  • Connection Voltage Ampere-hours Typical purpose
  • Series Adds Same as one cell Reach required bus / pack voltage
  • Parallel Same as one cell Adds Increase capacity / share current
  • Series–parallel Set by series count Set by parallel count of strings Meet both V and Ah needs
  • Internal Resistance and Terminal Voltage

Every real cell has internal resistance ( r or r_int ) caused by electrolyte, plates, separators, and connections. When current I is drawn, part of the EMF is dropped inside the cell.

V_terminal = E − I × r_internal (discharge, simple model)

Where:

  • E = open-circuit EMF (ideal source voltage)
  • I = load current
  • r_internal = internal resistance
  • V_terminal = voltage measured at the terminals under that load
  • Worked internal-resistance examples

E = 12.0 V , r = 0.05 Ω , I = 40 A (heavy load).

Drop = 40 × 0.05 = 2.0 V . V_terminal = 12.0 − 2.0 = 10.0 V .

Same battery at I = 5 A : drop = 0.25 V; V_terminal = 11.75 V . Light loads sag less.

Aged battery: E = 12.0 V , r = 0.2 Ω , I = 40 A .

  • Drop = 8.0 V; V_terminal = 4.0 V — may fail to crank even though open-circuit voltage looked “almost OK.”
  • Exam implications

High cranking current makes internal drop obvious—hence voltage falls during start.

Cold temperatures often raise effective internal resistance and reduce available capacity.

On charge, a simple model becomes V_terminal = E + I × r (applied voltage must overcome EMF and internal drop).

Always ask: is the stem quoting open-circuit EMF or loaded terminal voltage?

Thermocouples

A thermocouple is a junction of two dissimilar metals (or metal alloys) that produces a small EMF when the junction temperature differs from the reference— Seebeck effect . It is a heat-to-electricity transducer, not a battery substitute.

Construction and materials

Two wires of different thermoelectric materials joined at the hot (measuring) junction .

The other ends form the cold (reference) junction connection to the measuring instrument.

Common Type examples in industry (familiarisation): Type K (chromel–alumel), Type J (iron–constantan), Type T (copper–constantan). Aircraft engine temperature systems use approved material pairs and harnesses—not random workshop wire.

Operation

Heat the measuring junction (exhaust gas, cylinder head, turbine inlet probe, and so on).

A small DC millivolt-range EMF appears related to the temperature difference between junctions.

Instruments compensate for cold-junction temperature and scale millivolts to temperature readout.

Module 3 points: dissimilar metals + temperature difference → EMF; polarity depends on which metal is which; output is small (sensing), while aircraft power still comes from generators/batteries.

Aircraft framing

Thermocouples appear in EGT/TIT/CHT-style temperature measurement and similar monitoring. They generate a usable signal from heat; they do not energise a 28 V bus.

Photocells

A photocell (photoelectric cell) converts light into an electrical response. Depending on type, light may generate a voltage/current (photovoltaic behaviour) or change conduction (photoresistive / photoemissive families in older texts). Module 3 wants the principle: radiant energy → electrical effect .

Operation outline

Photons strike a photosensitive material.

Electrons are liberated or carrier behaviour changes, producing a current or voltage related to illumination.

Circuits measure that signal for light detection, flame sensing, or control inputs.

Aircraft / maintenance framing

Photocells and related light sensors support indication and control tasks (for example light-operated switches or sensing applications in equipment). Solar photovoltaic panels can produce useful power in other industries, but on Module 3 photocells sit with thermocouples as energy-conversion principles and sensors—not as the primary DC source architecture of a transport aircraft electrical system.

Sensors vs Batteries: Keep the Categories Clean

  • Source Energy input Typical output role
  • Chemical cell / battery Chemical Bulk stored DC energy
  • Thermocouple Heat (temperature difference) Small EMF for temperature measurement
  • Photocell Light Electrical signal / small photovoltaic response
  • Exam Scenario Drill

Scenario A: “Four 1.2 V, 10 Ah cells in series.” Answer: 4.8 V , 10 Ah .

Scenario B: “Four 1.2 V, 10 Ah cells in parallel.” Answer: 1.2 V , 40 Ah .

Scenario C: “E = 28 V, r = 0.1 Ω, I = 50 A.” Terminal voltage = 28 − 5 = 23 V .

Scenario D: “Device using two dissimilar metals generating EMF when heated.” → thermocouple .

Scenario E: “Device whose electrical output depends on incident light.” → photocell .

Master the arithmetic first—series/parallel mistakes are pure giveaway marks—then attach internal-resistance sag and the two sensor principles. That completes syllabus 3.5 DC Sources of Electricity for CAAS SAR-66 Module 3.