Study guide
9.2 Electromagnets & Hand Rules
CAAS SAR-66 AML Module 3 — Electrical Fundamentals Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 Current Exam Facts 1.2 Knowledge Levels & Study Approach for Module 3
2 Electron Theory & Static Electricity
2.1 Electron Theory & Atomic Structure 2.2 Conductors, Semiconductors & Insulators 2.3 Static Electricity, Coulomb's Law & Conduction
3 Terminology & Generation of Electricity
3.1 Electrical Terminology 3.2 Generation of Electricity
4 DC Sources of Electricity
4.1 Primary & Secondary Cells 4.2 Lead-Acid & Nickel-Cadmium Batteries 4.3 Series/Parallel Cells, Internal Resistance, Thermocouples & Photocells
5 DC Circuits
5.1 Ohm's Law 5.2 Kirchhoff's Voltage & Current Laws 5.3 Series/Parallel Networks & Supply Internal Resistance
6 Resistance & Resistors
6.1 Resistivity & Factors Affecting Resistance 6.2 Resistor Colour Code, Tolerance & Preferred Values 6.3 Series/Parallel Resistors, Potentiometers & Rheostats 6.4 Wheatstone Bridge, Thermistors & Temperature Coefficient
7 Power, Work & Energy
7.1 Power, Work & Energy Concepts 7.2 Power Dissipation & Calculations
8 Capacitance & Capacitors
8.1 Capacitor Operation & Factors Affecting Capacitance 8.2 Series/Parallel Capacitors & Types 8.3 RC Time Constants, Energy Storage & Testing
9 Magnetism
9.1 Theory of Magnetism & Magnetic Materials 9.2 Electromagnets & Hand Rules 9.3 MMF, Flux Density, Permeability, Hysteresis & Eddy Currents
10 Inductance & Inductors
10.1 Faraday's Law & Induced Voltage 10.2 Self & Mutual Inductance, Lenz's Law 10.3 Back EMF, Saturation & Inductor Applications
11 DC Motor/Generator Theory
11.1 Basic Motor & Generator Theory 11.2 DC Generators — Construction & Operation 11.3 DC Motors — Series, Shunt, Compound & Starter-Generators
12 AC Theory
12.1 Sinusoidal Waveforms — Phase, Period, Frequency 12.2 Peak, Average, RMS Values & Calculations 12.3 Non-Sinusoidal Waves & Single/Three-Phase Principles
13 R, L & C Circuits
13.1 Phase Relationships in R, L, C Circuits 13.2 Impedance, Phase Angle & Power Factor 13.3 True, Apparent & Reactive Power
14 Transformers
14.1 Transformer Construction & Operation 14.2 Losses, Efficiency, Load/No-Load & Turns Ratio 14.3 Three-Phase Transformers & Autotransformers
15 Filters & AC Generators
15.1 Filters — Low Pass, High Pass, Band Pass, Band Stop 15.2 AC Generator Principles & Construction 15.3 Star/Delta Connections & Permanent Magnet Generators
16 AC Motors
16.1 Synchronous & Induction Motors 16.2 Speed Control, Direction & Rotating Field Methods
9.2 Electromagnets & Hand Rules
Key Takeaways Explain This Topic AI
An electromagnet is a soft magnetic core wound with a current-carrying coil; field strength rises with ampere-turns and falls when current is removed (soft core)
Right-hand clasp (grip) rule: thumb in conventional current direction along a straight conductor; fingers curl in the magnetic field direction around the wire
For a solenoid, right-hand clasp: fingers follow conventional current in the turns; thumb points to the north pole end
Electromagnet polarity reverses if current reverses; strength depends on current, turns, and core permeability
Fleming’s left- and right-hand rules (motor/generator) are previewed here and applied fully with machines and induction topics later
Last updated: July 2026
9.2 Electromagnets & Hand Rules
Quick Answer: An electromagnet is a coil (often on a soft-iron core) energised by current. Field strength ≈ ampere-turns × core effect. Right-hand clasp rule: for a straight wire, thumb = conventional current, fingers = field circles; for a solenoid, fingers = current in turns, thumb = N pole. Reverse current → reverse poles. Fleming rules preview motor (left) and generator (right) force/EMF directions.
Topic 3.10 moves from permanent magnetism to electromagnetism : magnetism produced by electric current. Almost every aircraft electrical device that must pull, hold, or switch with controllable force — relays, solenoids, contactors, clutches, some valves — uses electromagnet principles.
Electromagnet Construction
A basic electromagnet has three ingredients:
- Part Role
- Coil (winding) Carries current; each turn contributes to magnetomotive force
- Core Soft magnetic material concentrating and strengthening flux
- Supply / switch Controls current on/off and sometimes polarity
Soft core preference. Soft iron or similar soft magnetic material magnetises strongly when current flows and largely demagnetises when current stops — ideal for relays and contactors that must release. A hard core would retain magnetism and might stick (residual hold).
Operation
Close the circuit → current I flows in N turns.
Magnetomotive force (ampere-turns, detailed in §9.3) establishes field strength H in the magnetic circuit.
The core’s high permeability produces large flux density B for a given H (until saturation).
External poles appear at the core ends (or armature air-gap faces).
Open the circuit → current falls to zero → soft core flux collapses → armature releases (ideally).
Factors affecting strength (qualitative Module 3 list):
- Increase this… Effect on electromagnet pull / field (before saturation)
- Current I Stronger field
- Number of turns N Stronger field (more ampere-turns)
- Core permeability / better magnetic circuit Stronger flux for same ampere-turns
- Air-gap length Weaker coupling — large gaps hurt pull
Worked qualitative example. A relay coil rated for 28 V DC draws a fixed current set by coil resistance. Doubling turns while keeping the same wire size and voltage is a design change (resistance also rises); conceptually Module 3 wants: more ampere-turns → stronger magnet , and soft core → releases when de-energised .
Polarity. The end that behaves as N or S depends on the sense of current around the coil. Reverse battery polarity → poles swap. That is why DC coil markings and diode suppression orientation matter in practice, and why hand rules matter on the exam.
Magnetic Field Around a Current-Carrying Conductor
A straight conductor carrying current is surrounded by circular magnetic field lines centred on the wire.
- Feature Description
- Shape Concentric circles in planes perpendicular to the wire
- Direction Given by the right-hand clasp (grip) rule using conventional current (+ to −)
- Strength Stronger near the wire; increases with current
- Reversal Reverse current → reverse field rotation
- Right-hand clasp rule — straight conductor
Point the thumb of the right hand in the direction of conventional current .
Fingers curl around the wire in the direction of the magnetic field .
End-view memory aids often drawn in textbooks:
Current out of the page (dot): field circles anticlockwise (right-hand rule).
Current into the page (cross): field circles clockwise .
Worked example. A vertical wire carries conventional current upward. Standing so you look with current going away from you into the distance is awkward — instead apply the rule directly: thumb up, fingers curl — that curl is the field direction around the wire. If the exam shows a cross-section with a cross (into page), field is clockwise.
Solenoid / Coil Hand Rule
A solenoid is a helical coil. Along its axis the fields of many turns add, producing a strong interior field similar to a bar magnet when energised.
Right-hand clasp rule — solenoid
Curl the fingers of the right hand in the direction of conventional current around the turns.
The thumb then points toward the north pole end of the solenoid.
- Check Result
- Reverse current N and S ends swap
- Soft-iron core inserted Much stronger external poles for same current
- More turns or more current Stronger magnet (until saturation)
Worked polarity example. Viewing a coil end, current runs clockwise around that face → that face is a south pole (because fingers clockwise imply thumb away from you into the coil — north at the far end, south nearest you). Counter-clockwise current on the near face → that face is north . Many CAAS-style stems show a coil sketch and ask which end is N.
Electromagnets in Aircraft Electrical Practice
- Device Electromagnet role
- Relay / contactor Coil pulls armature to close or open heavy contacts
- Solenoid valve Coil moves a plunger to open/close fluid or air path
- Magnetic circuit breaker trip elements Magnetic trip responds to overcurrent field
- Clutch / brake (specialised) Coil engages friction surfaces
- Inductor / transformer cores Soft magnetic cores shaped for AC flux (later chapters)
Failure modes linked to this section’s theory: open coil (no magnetism), shorted turns (weak pull / overheating), residual magnetism in a “soft” assembly that is actually contaminated or wrong material (sticky relay), excessive air gap (weak pull).
Fleming Context Preview (Motor & Generator)
Module 3 later formalises interaction of current, field, and motion. Two classic Fleming rules use the left or right hand with thumb, first finger, and second finger mutually perpendicular:
Rule Hand Typical association Finger meanings (common teaching set)
Fleming’s left-hand rule Left Motors (force on conductor) First finger = Field (B), seCond finger = Current, thuMb = Motion/force
Fleming’s right-hand rule Right Generators (induced EMF) First finger = Field, thuMb = Motion, seCond finger = induced Current / EMF sense
Memory bridge from clasp rules to Fleming:
Clasp / grip rules (this section) → direction of B around I , or poles of a coil .
Fleming left → which way a current-carrying conductor is pushed in a field (motor action).
Fleming right → which way induced current/EMF goes when a conductor moves in a field (generator action).
Do not confuse the right-hand clasp (field around a wire / solenoid north) with Fleming’s right-hand generator rule — same hand, different job. Exam stems that say “grip rule” or “clasp rule” want circular-field or solenoid-pole answers; stems that say “Fleming” want the three-finger motor/generator set.
Preview worked thought. Conductor in a uniform B-field carries current; left-hand rule gives force direction — that force is why DC motors rotate (Chapter on DC machines). Move a conductor across B; right-hand rule gives induced current sense — that is generator / Faraday territory (Inductance chapter).
Comparison Table: Permanent Magnet vs Electromagnet
- Feature Permanent magnet Electromagnet
- Field source Retained domain alignment Current in coil
- On/off control Not easily switched Switch current
- Polarity reverse Physically reverse magnet Reverse current
- Strength adjust Fixed (mostly) Vary I or effective turns
- Core type Hard magnetic material Soft magnetic core preferred
- Typical aircraft use Speakers, some sensors, latches Relays, contactors, solenoids
- Exam Focus Checklist
Name construction: coil + soft core + controllable current.
Apply right-hand clasp to a straight wire (thumb = I, fingers = B).
Apply right-hand clasp to a solenoid (fingers = I in turns, thumb = N).
State that reversing current reverses poles / field direction.
Distinguish clasp rules from Fleming left (motor) and right (generator) previews.
With construction and hand rules secure, §9.3 attaches the quantitative magnetic circuit language — MMF, H , B , μ, hysteresis, reluctance, saturation, and eddy currents — that Module 3 uses in calculations and loss explanations.