Study guide

9.1 Theory of Magnetism & Magnetic Materials

CAAS SAR-66 AML Module 3 — Electrical Fundamentals Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Knowledge Levels & Study Approach for Module 3

2 Electron Theory & Static Electricity

2.1 Electron Theory & Atomic Structure 2.2 Conductors, Semiconductors & Insulators 2.3 Static Electricity, Coulomb's Law & Conduction

3 Terminology & Generation of Electricity

3.1 Electrical Terminology 3.2 Generation of Electricity

4 DC Sources of Electricity

4.1 Primary & Secondary Cells 4.2 Lead-Acid & Nickel-Cadmium Batteries 4.3 Series/Parallel Cells, Internal Resistance, Thermocouples & Photocells

5 DC Circuits

5.1 Ohm's Law 5.2 Kirchhoff's Voltage & Current Laws 5.3 Series/Parallel Networks & Supply Internal Resistance

6 Resistance & Resistors

6.1 Resistivity & Factors Affecting Resistance 6.2 Resistor Colour Code, Tolerance & Preferred Values 6.3 Series/Parallel Resistors, Potentiometers & Rheostats 6.4 Wheatstone Bridge, Thermistors & Temperature Coefficient

7 Power, Work & Energy

7.1 Power, Work & Energy Concepts 7.2 Power Dissipation & Calculations

8 Capacitance & Capacitors

8.1 Capacitor Operation & Factors Affecting Capacitance 8.2 Series/Parallel Capacitors & Types 8.3 RC Time Constants, Energy Storage & Testing

9 Magnetism

9.1 Theory of Magnetism & Magnetic Materials 9.2 Electromagnets & Hand Rules 9.3 MMF, Flux Density, Permeability, Hysteresis & Eddy Currents

10 Inductance & Inductors

10.1 Faraday's Law & Induced Voltage 10.2 Self & Mutual Inductance, Lenz's Law 10.3 Back EMF, Saturation & Inductor Applications

11 DC Motor/Generator Theory

11.1 Basic Motor & Generator Theory 11.2 DC Generators — Construction & Operation 11.3 DC Motors — Series, Shunt, Compound & Starter-Generators

12 AC Theory

12.1 Sinusoidal Waveforms — Phase, Period, Frequency 12.2 Peak, Average, RMS Values & Calculations 12.3 Non-Sinusoidal Waves & Single/Three-Phase Principles

13 R, L & C Circuits

13.1 Phase Relationships in R, L, C Circuits 13.2 Impedance, Phase Angle & Power Factor 13.3 True, Apparent & Reactive Power

14 Transformers

14.1 Transformer Construction & Operation 14.2 Losses, Efficiency, Load/No-Load & Turns Ratio 14.3 Three-Phase Transformers & Autotransformers

15 Filters & AC Generators

15.1 Filters — Low Pass, High Pass, Band Pass, Band Stop 15.2 AC Generator Principles & Construction 15.3 Star/Delta Connections & Permanent Magnet Generators

16 AC Motors

16.1 Synchronous & Induction Motors 16.2 Speed Control, Direction & Rotating Field Methods

9.1 Theory of Magnetism & Magnetic Materials

Key Takeaways Explain This Topic AI

A magnet has two poles (N and S); like poles repel and unlike poles attract; flux lines leave the north pole externally and enter the south pole

Earth behaves as a huge magnet; the geographic North Pole is near a magnetic south pole, so a compass north-seeking end points geographic north

Magnetisation aligns magnetic domains; demagnetisation disorders them by heat, shock, or an alternating field that is gradually reduced to zero

Magnetic shielding uses high-permeability soft materials to divert flux around a sensitive region rather than “blocking” magnetism with an insulator

Hard magnetic materials retain magnetism (permanent magnets); soft magnetic materials magnetise and demagnetise easily (cores, shields); store magnets with keepers and away from instruments

Last updated: July 2026

9.1 Theory of Magnetism & Magnetic Materials

Quick Answer: Magnets have north and south poles; like poles repel , unlike poles attract . External flux leaves N and enters S . Earth is a weak but global magnetic field. Hard materials keep magnetism (permanent magnets); soft materials take and lose magnetism easily (cores, shields). Heat, shock, or a decaying AC field can demagnetise; high-μ soft iron shields by diverting flux.

CAAS SAR-66 Module 3 topic 3.10 Magnetism is the bridge between DC circuit theory and electromagnetism, inductance, and rotating machines. Before you write Fleming’s rules or talk about flux density in amperes per metre and teslas, you need a clear picture of what a magnet is , how the Earth field behaves, how materials become magnets or lose magnetism, and how technicians store and shield magnetic devices around aircraft instruments.

Properties of a Magnet

A magnet is a body that produces a magnetic field and exerts force on ferromagnetic materials and on other magnets. Every magnet has two poles:

  • Property Statement (exam language)
  • Poles Always in pairs — north-seeking (N) and south-seeking (S)
  • Force law Like poles repel ; unlike poles attract
  • External flux Lines leave N , enter S , form closed loops
  • Internal path Inside the magnet, flux returns from S toward N
  • Strength Strongest near the poles; weakens with distance
  • Indivisibility Breaking a bar magnet yields two smaller magnets, each with N and S

Magnetic flux lines (lines of force) are a visualisation aid:

They never cross.

They form closed loops.

Density of lines represents field strength (later formalised as flux density B ).

They take the path of least reluctance through soft magnetic materials.

Worked concept check. Two bar magnets face N-to-N. They repel . Turn one so N faces S: they attract . A soft-iron nail placed near either pole becomes a temporary magnet (induced poles) and is attracted — that is magnetic induction, not “electric charge attraction.”

Domain picture (Level 2 depth)

In ferromagnetic materials (iron, nickel, cobalt, and many alloys), groups of atomic magnets form domains . In an unmagnetised piece, domains point randomly and cancel. In a magnetised piece, domains align preferentially toward one direction, producing external N and S poles. This mental model supports later ideas of saturation (almost all domains aligned) and hysteresis (domains lag the magnetising field).

Earth’s Magnetic Field

The Earth behaves like a huge bar magnet. Important Module 3 / navigation-adjacent facts:

  • Idea Practical meaning
  • Geographic vs magnetic Geographic North Pole ≠ magnetic pole location

Compass “north” The north-seeking end of a compass is attracted toward the Earth’s magnetic south region near geographic north

  • Declination Angle between true north and magnetic north — charts and aircraft systems account for it
  • Dip / inclination Field lines are not horizontal everywhere; they dip into the Earth

Weak field Earth’s field is weak compared with a workshop permanent magnet or an electromagnet, but it is enough to orient compasses and to bias sensitive instruments if magnets are stored carelessly nearby

For Module 3 electrical fundamentals you are not examining IFR navigation procedures; you are expected to know that Earth has a magnetic field with poles, that a freely suspended magnet aligns with it, and that the naming of poles follows the north-seeking / south-seeking convention.

  • Magnetisation and Demagnetisation
  • Magnetisation (making a magnet)

Common training methods:

  • Method How it works Typical use
  • Stroking with a permanent magnet Repeated unidirectional strokes align domains Simple demos; weak magnets

Direct current through a coil (electromagnet) Strong H-field aligns domains in a core or workpiece Electromagnets, magnetisers

Placing in a strong field while cooling (special processes) Domains “freeze” into alignment Industrial permanent-magnet manufacture

Retentivity (covered in depth in §9.3) decides whether the piece stays magnetised after the field is removed — hard materials retain; soft materials largely lose magnetism when H is removed.

Demagnetisation (degaussing)

Domains must be disordered again:

Method Mechanism Hangar / shop note

Heating above Curie temperature Thermal agitation destroys alignment Permanent damage risk to coatings/insulation — controlled process

Severe mechanical shock Jars domains out of alignment Accidental drop can weaken a magnet or tool

Alternating field reduced to zero AC coil or degausser; amplitude decreased gradually so residual domains cancel Preferred controlled method for tools, watches, some instruments

Worked scenario. A steel tool becomes lightly magnetised and attracts filings. Passing it slowly through (or near) a degaussing coil while withdrawing it as the AC field decays leaves domains randomised → tool is demagnetised.

Magnetic Shielding

There is no magnetic insulator analogous to rubber for electricity. Shielding works by providing a low-reluctance path that diverts flux around a protected volume.

  • Shielding idea Detail
  • Material Soft, high-permeability alloys (soft iron, mu-metal class materials in precision work)
  • Geometry Closed or nearly closed magnetic path around the sensitive item
  • Effect Flux prefers the shield; interior field is reduced

Wrong idea “Thick plastic stops magnetism” — false; non-magnetic materials do not provide a preferred flux path

Aircraft and avionics context: keep strong magnets and magnetised tools away from magnetic compasses and magnetically sensitive sensors; where shielding is designed in, it is soft magnetic enclosures or intentional soft-iron paths — not ordinary insulation tape.

Types of Magnetic Material

Module 3 classifies materials by how they respond to magnetic fields:

  • Class Behaviour Examples / use
  • Ferromagnetic Strongly attracted; can be magnetised Iron, steel, nickel, cobalt, ferrites
  • Paramagnetic Weakly attracted Aluminium, platinum (weak effects)
  • Diamagnetic Weakly repelled Copper, bismuth, many non-magnetics

Hard magnetic High remanence / high coercivity — permanent magnets Alnico, hard steel, ceramic/rare-earth magnet materials

Soft magnetic Low coercivity — easy to magnetise and demagnetise Soft iron, silicon steel laminations, soft ferrites

Hard vs soft (exam gold):

Hard → permanent magnets, speakers, some sensors, latch magnets.

Soft → transformer and inductor cores, relay armatures, magnetic shields, motor laminations (also reduces eddy-current issues when laminated — §9.3).

Non-magnetic materials (brass, most aluminium alloys, copper, many plastics, austenitic stainless grades used as “non-magnetic”) are chosen where you must not distort local fields or create unwanted attraction.

Storage Precautions

Permanent magnets and magnetised assemblies need disciplined storage — especially near aircraft magnetic compasses and workshop instruments.

Precaution Why

Use keepers (soft-iron bars bridging N–S on horseshoe or across bar ends) Provides a closed flux path; reduces self-demagnetising open-circuit field and preserves strength

Store magnets together with opposite poles adjacent when keepers are used as designed Maintains closed magnetic circuit

Keep away from compasses, CRTs/legacy instruments, magnetic media, and sensitive avionics Stray fields cause errors or damage

Avoid heat, hammering, and dropping Demagnetises or cracks brittle magnet materials

Do not store strong magnets against soft-iron tools unintentionally Tools become magnetised; filings and FOD risk

Label and segregate magnetised tooling Prevents accidental approach to aircraft during compass swing / maintenance

Aircraft maintenance link. Before work near a magnetic compass or flux valve, control magnetised tools and permanent-magnet devices. A “harmless” magnetic base or magnetised screwdriver left in the cockpit can throw compass readings — exactly the practical reason Module 3 stresses storage and shielding alongside theory.

Section Synthesis Table

  • Topic One-line exam takeaway
  • Poles & force Unlike attract, like repel; flux out N, in S
  • Earth Global field; compass north-seeking end points geographic north
  • Magnetise Align domains (stroke, DC coil, process fields)
  • Demagnetise Heat, shock, or decaying AC field
  • Shield High-μ soft path diverts flux
  • Hard / soft Retain vs easy magnetise–demagnetise
  • Storage Keepers, segregation, no heat/shock near instruments

Master these qualitative rules before §9.2 turns magnetism into electromagnets and hand rules, and §9.3 attaches the quantitative language of MMF, B , permeability, hysteresis, and eddy currents.