Study guide

7.1 Power, Work & Energy Concepts

CAAS SAR-66 AML Module 3 — Electrical Fundamentals Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Knowledge Levels & Study Approach for Module 3

2 Electron Theory & Static Electricity

2.1 Electron Theory & Atomic Structure 2.2 Conductors, Semiconductors & Insulators 2.3 Static Electricity, Coulomb's Law & Conduction

3 Terminology & Generation of Electricity

3.1 Electrical Terminology 3.2 Generation of Electricity

4 DC Sources of Electricity

4.1 Primary & Secondary Cells 4.2 Lead-Acid & Nickel-Cadmium Batteries 4.3 Series/Parallel Cells, Internal Resistance, Thermocouples & Photocells

5 DC Circuits

5.1 Ohm's Law 5.2 Kirchhoff's Voltage & Current Laws 5.3 Series/Parallel Networks & Supply Internal Resistance

6 Resistance & Resistors

6.1 Resistivity & Factors Affecting Resistance 6.2 Resistor Colour Code, Tolerance & Preferred Values 6.3 Series/Parallel Resistors, Potentiometers & Rheostats 6.4 Wheatstone Bridge, Thermistors & Temperature Coefficient

7 Power, Work & Energy

7.1 Power, Work & Energy Concepts 7.2 Power Dissipation & Calculations

8 Capacitance & Capacitors

8.1 Capacitor Operation & Factors Affecting Capacitance 8.2 Series/Parallel Capacitors & Types 8.3 RC Time Constants, Energy Storage & Testing

9 Magnetism

9.1 Theory of Magnetism & Magnetic Materials 9.2 Electromagnets & Hand Rules 9.3 MMF, Flux Density, Permeability, Hysteresis & Eddy Currents

10 Inductance & Inductors

10.1 Faraday's Law & Induced Voltage 10.2 Self & Mutual Inductance, Lenz's Law 10.3 Back EMF, Saturation & Inductor Applications

11 DC Motor/Generator Theory

11.1 Basic Motor & Generator Theory 11.2 DC Generators — Construction & Operation 11.3 DC Motors — Series, Shunt, Compound & Starter-Generators

12 AC Theory

12.1 Sinusoidal Waveforms — Phase, Period, Frequency 12.2 Peak, Average, RMS Values & Calculations 12.3 Non-Sinusoidal Waves & Single/Three-Phase Principles

13 R, L & C Circuits

13.1 Phase Relationships in R, L, C Circuits 13.2 Impedance, Phase Angle & Power Factor 13.3 True, Apparent & Reactive Power

14 Transformers

14.1 Transformer Construction & Operation 14.2 Losses, Efficiency, Load/No-Load & Turns Ratio 14.3 Three-Phase Transformers & Autotransformers

15 Filters & AC Generators

15.1 Filters — Low Pass, High Pass, Band Pass, Band Stop 15.2 AC Generator Principles & Construction 15.3 Star/Delta Connections & Permanent Magnet Generators

16 AC Motors

16.1 Synchronous & Induction Motors 16.2 Speed Control, Direction & Rotating Field Methods

7.1 Power, Work & Energy Concepts

Key Takeaways Explain This Topic AI

Work and energy share the joule (J); power is the rate of energy transfer and uses the watt (W), where 1 W = 1 J/s

Electrical power delivered to a load is P = VI; for a pure resistor this equals I²R and V²/R

Kinetic energy depends on motion (½mv²); potential energy depends on position or stored field/chemical state

Energy transferred equals power × time: W = Pt (with consistent SI units) — Module 3 uses this for heating and battery drain estimates

CAAS SAR-66 Module 3 topic 3.8 expects fluent SI units and the work–energy–power triangle applied to aircraft DC circuits

Last updated: July 2026

7.1 Power, Work & Energy Concepts

Quick Answer: Energy is the capacity to do work ; both are measured in joules (J) . Power is how fast energy is transferred or converted — measured in watts (W) , where 1 W = 1 J/s . In DC circuits, instantaneous electrical power into a load is P = VI . Remember: energy = power × time ( W = Pt in consistent SI units).

CAAS SAR-66 Module 3 topic 3.8 Power sits after resistance (3.7) and before capacitance (3.9). You already know voltage, current, and resistance from topics 3.3 and 3.6–3.7. Power answers the maintenance question those quantities alone do not: how hard is this circuit working, and how much heat or mechanical output should I expect?

Work: Force Through a Distance

In mechanics, work done by a constant force in the direction of motion is:

  • Work = force × distance
  • W = F × d
  • Quantity SI unit Symbol
  • Force newton (N) F
  • Distance metre (m) d
  • Work joule (J) W

1 joule = 1 newton·metre (N·m). If you push with 10 N through 2 m (in the force direction), work = 20 J.

Worked example 1 — mechanical work. A technician applies an average 50 N force while sliding a tool chest 3.0 m along a hangar floor (force aligned with motion). Work = 50 × 3.0 = 150 J .

If the force is perpendicular to the displacement, that force component does no work . Module 3 uses the aligned case for definitions; the exam cares that work and energy share the joule .

Energy: Capacity to Do Work

Energy is the capacity to do work. When a system does 150 J of work, it transfers or converts 150 J of energy . Units match: both use J .

Energy is never “created from nothing” in Module 3 reasoning — it transforms . Chemical energy in a battery becomes electrical energy in the circuit, then thermal energy in a resistor or mechanical energy in a motor.

Kinetic energy (energy of motion)

Kinetic energy (KE) depends on mass and speed:

KE = ½ m v²

  • Symbol Meaning SI unit
  • m Mass kilogram (kg)
  • v Speed metre per second (m/s)
  • KE Kinetic energy joule (J)

Worked example 2 — kinetic energy. A 2.0 kg mass moves at 3.0 m/s.

KE = ½ × 2.0 × (3.0)² = 1.0 × 9.0 = 9.0 J .

Double the speed → four times the kinetic energy, because of v² . That squared dependence is a frequent trap on calculation stems.

Potential energy (energy of position or stored state)

Potential energy (PE) is stored energy associated with position or configuration. Common Module 3–relevant forms:

  • Form Everyday / aircraft idea Rough dependence
  • Gravitational PE Object raised against gravity m g h (height h)
  • Elastic / spring PE Stretched spring or pressurised system stored mechanical state
  • Chemical PE Battery, fuel convertible to electrical / thermal / mechanical
  • Electrical PE (field) Charge separated across a potential difference linked to voltage and charge

Gravitational PE (near Earth, constant g):

PE = m g h

Worked example 3 — gravitational PE. Raise a 5.0 kg component by 2.0 m (g ≈ 9.8 m/s²).

PE ≈ 5.0 × 9.8 × 2.0 = 98 J .

That 98 J came from the work you did lifting it. If the part falls freely (idealised), PE converts toward KE.

Electrical perspective: A charge q moved through a potential difference V gains or loses electrical potential energy qV (joules when q is in coulombs and V in volts). A battery “stores” chemical energy that the circuit converts as charge flows through voltage drops.

Power: Rate of Doing Work / Transferring Energy

Power is work done (or energy transferred) per unit time :

P = W / t

Equivalently, energy = power × time :

W = P × t

  • Quantity SI unit Notes
  • Power watt (W) 1 W = 1 J/s
  • Energy / work joule (J) also W·s
  • Time second (s) use seconds in SI calculations

Larger units you will see:

  • 1 kW = 1 000 W
  • 1 MJ = 10⁶ J
  • In industry, energy is often quoted in kilowatt-hours (kWh) : 1 kWh = 1 000 W × 3 600 s = 3.6 × 10⁶ J = 3.6 MJ

Module 3 prefers SI (W, J, s) for exam arithmetic, but recognising that a watt is a rate prevents mixing energy and power on stems.

Worked example 4 — power from work and time. A hoist does 2 400 J of useful work in 8.0 s.

P = 2 400 / 8.0 = 300 W .

Worked example 5 — energy from power and time. A 60 W lamp runs for 5.0 minutes (300 s).

Energy = P t = 60 × 300 = 18 000 J = 18 kJ .

If the stem gives minutes or hours, convert to seconds before multiplying, or carefully use hours only with kW·h.

Electrical Power: P = VI

In a DC circuit, the electrical power delivered to a two-terminal load is:

P = V I

  • Symbol Meaning SI unit
  • P Power watt (W)
  • V Voltage across the load volt (V)
  • I Current through the load ampere (A)

Why it works: Voltage is energy per coulomb; current is coulombs per second. Product is joules per second = watts.

Worked example 6 — bus load. A heater on a 28 V aircraft DC bus draws 5.0 A .

P = 28 × 5.0 = 140 W .

Every second, about 140 J of electrical energy converts mainly to heat in the heater element.

Worked example 7 — rearrange for current. A 12 V landing-light circuit dissipates 48 W at the lamp (idealised).

I = P / V = 48 / 12 = 4.0 A .

Worked example 8 — rearrange for voltage. A resistor dissipates 18 W at 3.0 A.

V = P / I = 18 / 3.0 = 6.0 V across that resistor.

Link to Ohm’s law (preview of §7.2)

For a pure resistance with V = IR:

  • P = I²R (substitute V = IR into P = VI)
  • P = V²/R (substitute I = V/R into P = VI)

All three forms describe the same instantaneous dissipation when Ohm’s law holds. Choose the form that matches the known quantities.

Work, Energy, and Power Triangle

Keep this mental map for Module 3:

Work / energy → how much (joules).

Power → how fast (watts = joules per second).

Time → the bridge: W = P t and P = W / t.

Conservation framing for technicians: Energy leaving the electrical circuit as heat in a resistor, light from a lamp, or shaft work from a motor equals the electrical energy delivered ( ∫ P dt , or P t if power is constant). Losses in wiring are still energy — they just appear as unwanted I²R heating of conductors (developed fully in §7.2).

Aircraft and Training Context

Situation Energy / power idea

Battery ampere-hour rating Stored charge capacity; usable energy also depends on voltage and discharge conditions

Generator / alternator rating Often stated in watts or volt-amperes — a power (rate) capability

Circuit breaker / wire sizing Must handle continuous current without excessive heating — heating rate tracks I²R

Resistor wattage marking Maximum continuous dissipation the part can reject as heat

Worked example 9 — constant power energy. A 100 W avionics heater (training figure) runs for 10 minutes at rated power.

Energy = 100 W × 600 s = 60 000 J = 60 kJ .

Worked example 10 — compare rates. Device A transfers 500 J in 2 s → P = 250 W. Device B transfers 500 J in 10 s → P = 50 W. Same energy, different power — different thermal and supply stress.

Exam Pitfalls to Avoid

Calling joules “power” or watts “energy”.

Forgetting v² in kinetic energy.

Using minutes in W = P t without converting.

Mixing peak and continuous ratings (Module 3 starts with steady DC P = VI).

Master the SI definitions, KE and PE ideas, P = W/t , and P = VI . Section 7.2 then drills dissipation formulas, resistor heating, and conductor I²R losses that CAAS stems favour.