Study guide

6.1 Resistivity & Factors Affecting Resistance

CAAS SAR-66 AML Module 3 — Electrical Fundamentals Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Knowledge Levels & Study Approach for Module 3

2 Electron Theory & Static Electricity

2.1 Electron Theory & Atomic Structure 2.2 Conductors, Semiconductors & Insulators 2.3 Static Electricity, Coulomb's Law & Conduction

3 Terminology & Generation of Electricity

3.1 Electrical Terminology 3.2 Generation of Electricity

4 DC Sources of Electricity

4.1 Primary & Secondary Cells 4.2 Lead-Acid & Nickel-Cadmium Batteries 4.3 Series/Parallel Cells, Internal Resistance, Thermocouples & Photocells

5 DC Circuits

5.1 Ohm's Law 5.2 Kirchhoff's Voltage & Current Laws 5.3 Series/Parallel Networks & Supply Internal Resistance

6 Resistance & Resistors

6.1 Resistivity & Factors Affecting Resistance 6.2 Resistor Colour Code, Tolerance & Preferred Values 6.3 Series/Parallel Resistors, Potentiometers & Rheostats 6.4 Wheatstone Bridge, Thermistors & Temperature Coefficient

7 Power, Work & Energy

7.1 Power, Work & Energy Concepts 7.2 Power Dissipation & Calculations

8 Capacitance & Capacitors

8.1 Capacitor Operation & Factors Affecting Capacitance 8.2 Series/Parallel Capacitors & Types 8.3 RC Time Constants, Energy Storage & Testing

9 Magnetism

9.1 Theory of Magnetism & Magnetic Materials 9.2 Electromagnets & Hand Rules 9.3 MMF, Flux Density, Permeability, Hysteresis & Eddy Currents

10 Inductance & Inductors

10.1 Faraday's Law & Induced Voltage 10.2 Self & Mutual Inductance, Lenz's Law 10.3 Back EMF, Saturation & Inductor Applications

11 DC Motor/Generator Theory

11.1 Basic Motor & Generator Theory 11.2 DC Generators — Construction & Operation 11.3 DC Motors — Series, Shunt, Compound & Starter-Generators

12 AC Theory

12.1 Sinusoidal Waveforms — Phase, Period, Frequency 12.2 Peak, Average, RMS Values & Calculations 12.3 Non-Sinusoidal Waves & Single/Three-Phase Principles

13 R, L & C Circuits

13.1 Phase Relationships in R, L, C Circuits 13.2 Impedance, Phase Angle & Power Factor 13.3 True, Apparent & Reactive Power

14 Transformers

14.1 Transformer Construction & Operation 14.2 Losses, Efficiency, Load/No-Load & Turns Ratio 14.3 Three-Phase Transformers & Autotransformers

15 Filters & AC Generators

15.1 Filters — Low Pass, High Pass, Band Pass, Band Stop 15.2 AC Generator Principles & Construction 15.3 Star/Delta Connections & Permanent Magnet Generators

16 AC Motors

16.1 Synchronous & Induction Motors 16.2 Speed Control, Direction & Rotating Field Methods

6.1 Resistivity & Factors Affecting Resistance

Key Takeaways Explain This Topic AI

Resistance of a uniform conductor is R = ρL/A, where ρ is resistivity, L is length, and A is cross-sectional area

For a given material and temperature, doubling length doubles R; doubling area halves R

Resistivity ρ is a material property (ohm·metre); copper has low ρ, nichrome and carbon have much higher ρ

Most metallic conductors have a positive temperature coefficient of resistance — R rises as temperature rises

Aircraft wiring, bonding straps, and high-resistance joints are practical applications of the same R = ρL/A and temperature rules tested on CAAS Module 3

Last updated: July 2026

6.1 Resistivity & Factors Affecting Resistance

Quick Answer: For a uniform conductor, R = ρL/A . Resistance rises with length and resistivity , falls as cross-sectional area increases, and usually rises with temperature in metals. Resistivity ρ is the material property (ohm·metre); Module 3 expects you to rearrange the formula, compare materials, and apply temperature-coefficient ideas to conductors and resistors.

CAAS SAR-66 Module 3 topic 3.7 Resistance / resistor starts with why a wire or resistor has the ohm value it has. Topic 3.3 already defined resistance as opposition to current; here you quantify that opposition from geometry and material, then link temperature behaviour to maintenance symptoms such as hot joints and rising feeder drop on a 28 V DC bus.

The Resistance Formula: R = ρL/A

For a conductor of uniform cross-section:

R = ρL / A

  • Symbol Meaning Typical SI unit
  • R Resistance ohm (Ω)
  • ρ (rho) Resistivity of the material ohm·metre (Ω·m)
  • L Length of the conductor metre (m)
  • A Cross-sectional area square metre (m²)

Read the formula as three independent levers:

Material sets ρ .

Length sets how much material the current must travel through.

Area sets how wide the conduction path is.

Direct and inverse relationships (exam gold)

R ∝ L — double the length → double the resistance (same material, same A, same temperature).

R ∝ 1/A — double the cross-sectional area → half the resistance.

R ∝ ρ — higher resistivity material → higher resistance for identical size.

Worked example 1 — rearrange for resistivity. A copper bar is 2.0 m long, has A = 1.0 × 10⁻⁶ m², and measures R = 0.034 Ω at the stated temperature. Find ρ.

ρ = RA / L = (0.034 × 1.0 × 10⁻⁶) / 2.0 = 1.7 × 10⁻⁸ Ω·m (order of magnitude of copper).

Worked example 2 — length change. A bonding strap has R = 0.020 Ω. An alternative strap of the same material and cross-section is 1.5 times as long. New resistance = 0.020 × 1.5 = 0.030 Ω .

Worked example 3 — area change. A feeder cable has R = 0.080 Ω. Replacing it with a cable of twice the cross-sectional area (same length and material) gives R = 0.080 / 2 = 0.040 Ω . Lower R means less I²R heating and less voltage drop for the same load current.

Worked example 4 — combined change. Original wire: R₁ = ρL / A. New wire: twice as long and half the area → R₂ = ρ(2L) / (A/2) = 4 × (ρL/A) = 4R₁ . Combined geometry mistakes are common on Module 3 — multiply the factors carefully.

Resistivity: The Material Fingerprint

Resistivity (ρ) is resistance of a sample of unit length and unit cross-sectional area. It lets you compare materials without arguing about wire size.

  • Material (typical order) Relative resistivity Aviation / training use
  • Silver Very low Best conductor; costly — rarely used as bulk wiring
  • Copper Very low Primary aircraft power and signal wiring
  • Aluminium Low (higher than Cu) Weight-sensitive power runs; watch joints and oxide
  • Tungsten Higher Lamp filaments (high melting point)
  • Nichrome (Ni-Cr alloy) High Heating elements, some high-stability resistors
  • Carbon / graphite High (and NTC behaviour often) Resistor compositions, brushes
  • Insulators (glass, plastics) Extremely high Insulation — not used as intentional conductors

You do not need to memorise every textbook ρ table to the last digit for CAAS Module 3, but you must know the ranking logic: copper and aluminium are low-ρ conductors; nichrome and carbon are much higher; good insulators have enormous ρ . If a stem says “same dimensions, which has highest resistance?” pick the highest-ρ material listed.

Conductivity is the reciprocal idea: materials with low resistivity are high-conductivity conductors. Mentally: low ρ ↔ easy current ↔ low R for a given L and A.

Cross-Section and Length in Aircraft Context

Aircraft electrical practice is full of R = ρL/A decisions even when nobody writes the Greek letter:

Undersized cables (small A) raise R → voltage drop and heat under load.

Long feeder runs (large L) raise R → remote equipment may see less than bus voltage.

Bonding straps must be short and adequate in section so airframe equipotential bonding stays low-resistance.

Corroded or loose joints add contact resistance that is not in the ideal ρL/A wire calculation — but the symptom (heat, drop) looks the same.

Voltage-drop check: Drop in a feeder ≈ I × R_feeder . At 40 A through 0.05 Ω, drop = 2.0 V . On a nominal 28 V DC bus, the load may see about 26 V. Raising A (thicker cable) or shortening L cuts R and the drop.

Temperature and Resistance

Most pure metallic conductors have a positive temperature coefficient of resistance (PTC behaviour in the broad sense) : as temperature rises, lattice vibration increases, electron drift is impeded more, and R increases .

A linear approximation often taught for Module 3 is:

R_t = R₀ [1 + α(t − t₀)]

where:

  • R_t = resistance at temperature t
  • R₀ = resistance at reference temperature t₀
  • α (alpha) = temperature coefficient of resistance (°C⁻¹)

Worked example 5 — temperature rise. A copper winding has R₀ = 10.0 Ω at 20 °C. If α ≈ 0.004 /°C and the winding reaches 70 °C:

R₇₀ = 10.0 [1 + 0.004(70 − 20)] = 10.0 [1 + 0.20] = 12.0 Ω .

A 20% rise in resistance for a 50 °C rise is the sort of magnitude Module 3 expects you to recognise — metals warm up, resistance climbs.

Positive vs negative temperature coefficient (preview of §6.4)

  • Behaviour Resistance vs temperature Typical materials / devices
  • Positive TCR R rises as T rises Most metals, PTC thermistors
  • Negative TCR R falls as T rises Carbon (often), NTC thermistors

Carbon composition resistors and NTC thermistors are the classic “resistance falls when hot” counter-examples. Do not assume every resistor behaves like copper wire.

Factors Summary Table

  • Factor If it increases… Effect on R (others fixed)
  • Length L Longer path R increases
  • Area A Wider path R decreases
  • Resistivity ρ “Worse” conductor material R increases
  • Temperature (most metals) Hotter conductor R increases
  • Exam Scenarios to Rehearse

Scenario A — Same wire, cut in half. Half the length → half the resistance of that piece (and half the voltage drop for the same current through that segment).

Scenario B — Parallel paths vs area. Two identical conductors in parallel behave like roughly twice the conducting area → about half the resistance of one alone (link forward to series/parallel in §6.3).

Scenario C — Hot connector. Measured millivolt drop across a joint rises under load as contact resistance heats — temperature and effective R climb together until cleaned or retorqued.

Scenario D — Material swap. Replacing copper with nichrome of identical L and A multiplies R by ρ_nichrome / ρ_copper (large factor) — useful for heaters, disastrous for power feeders.

Master R = ρL/A , the four factors, and the metallic temperature trend. Those tools unlock colour-code wattage limits, series/parallel networks, and thermistor bridges later in this chapter.