Study guide

6.4 Wheatstone Bridge, Thermistors & Temperature Coefficient

CAAS SAR-66 AML Module 3 — Electrical Fundamentals Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Knowledge Levels & Study Approach for Module 3

2 Electron Theory & Static Electricity

2.1 Electron Theory & Atomic Structure 2.2 Conductors, Semiconductors & Insulators 2.3 Static Electricity, Coulomb's Law & Conduction

3 Terminology & Generation of Electricity

3.1 Electrical Terminology 3.2 Generation of Electricity

4 DC Sources of Electricity

4.1 Primary & Secondary Cells 4.2 Lead-Acid & Nickel-Cadmium Batteries 4.3 Series/Parallel Cells, Internal Resistance, Thermocouples & Photocells

5 DC Circuits

5.1 Ohm's Law 5.2 Kirchhoff's Voltage & Current Laws 5.3 Series/Parallel Networks & Supply Internal Resistance

6 Resistance & Resistors

6.1 Resistivity & Factors Affecting Resistance 6.2 Resistor Colour Code, Tolerance & Preferred Values 6.3 Series/Parallel Resistors, Potentiometers & Rheostats 6.4 Wheatstone Bridge, Thermistors & Temperature Coefficient

7 Power, Work & Energy

7.1 Power, Work & Energy Concepts 7.2 Power Dissipation & Calculations

8 Capacitance & Capacitors

8.1 Capacitor Operation & Factors Affecting Capacitance 8.2 Series/Parallel Capacitors & Types 8.3 RC Time Constants, Energy Storage & Testing

9 Magnetism

9.1 Theory of Magnetism & Magnetic Materials 9.2 Electromagnets & Hand Rules 9.3 MMF, Flux Density, Permeability, Hysteresis & Eddy Currents

10 Inductance & Inductors

10.1 Faraday's Law & Induced Voltage 10.2 Self & Mutual Inductance, Lenz's Law 10.3 Back EMF, Saturation & Inductor Applications

11 DC Motor/Generator Theory

11.1 Basic Motor & Generator Theory 11.2 DC Generators — Construction & Operation 11.3 DC Motors — Series, Shunt, Compound & Starter-Generators

12 AC Theory

12.1 Sinusoidal Waveforms — Phase, Period, Frequency 12.2 Peak, Average, RMS Values & Calculations 12.3 Non-Sinusoidal Waves & Single/Three-Phase Principles

13 R, L & C Circuits

13.1 Phase Relationships in R, L, C Circuits 13.2 Impedance, Phase Angle & Power Factor 13.3 True, Apparent & Reactive Power

14 Transformers

14.1 Transformer Construction & Operation 14.2 Losses, Efficiency, Load/No-Load & Turns Ratio 14.3 Three-Phase Transformers & Autotransformers

15 Filters & AC Generators

15.1 Filters — Low Pass, High Pass, Band Pass, Band Stop 15.2 AC Generator Principles & Construction 15.3 Star/Delta Connections & Permanent Magnet Generators

16 AC Motors

16.1 Synchronous & Induction Motors 16.2 Speed Control, Direction & Rotating Field Methods

6.4 Wheatstone Bridge, Thermistors & Temperature Coefficient

Key Takeaways Explain This Topic AI

A Wheatstone bridge is balanced when R1/R2 = R3/R4 (product of opposite arms equal), giving zero galvanometer/detector voltage

NTC thermistors decrease resistance as temperature rises; PTC thermistors increase resistance as temperature rises

Thermistors provide sensitive temperature measurement and compensation; VDRs (varistors) change resistance strongly with applied voltage

Fixed resistors offer stable values within tolerance; variable types (pots, rheostats, thermistors, VDRs) trade stability for adjustability or sensing

Temperature coefficient links §6.1 metallic behaviour to thermistor and bridge measurement techniques tested in Module 3 topic 3.7

Last updated: July 2026

6.4 Wheatstone Bridge, Thermistors & Temperature Coefficient

Quick Answer: A Wheatstone bridge balances when R₁/R₂ = R₃/R₄ (equivalently R₁ R₄ = R₂ R₃ ), so the mid-points are at equal potential. NTC thermistors fall in R as temperature rises; PTC rise in R as temperature rises. VDRs (varistors) change R with voltage. Know fixed vs variable resistor roles and limits.

Topic 3.7 finishes by connecting resistance to measurement and sensing . Bridges measure unknown resistance accurately; thermistors convert temperature to resistance; VDRs protect or sense based on voltage.

Wheatstone Bridge — Construction and Balance

A classical Wheatstone bridge has four resistive arms in a diamond (or rectangle) arrangement:

Two voltage dividers share the same supply.

A galvanometer or detector connects between the divider mid-points.

Label the arms so that one divider is R₁ (top) and R₂ (bottom), the other R₃ (top) and R₄ (bottom), with the meter between the junctions of R₁–R₂ and R₃–R₄. (Textbook lettering varies; learn the ratio condition , not one fragile letter pattern.)

Balance condition

At balance , detector current is zero and the two mid-point potentials are equal. Then:

  • R₁ / R₂ = R₃ / R₄
  • or
  • R₁ × R₄ = R₂ × R₃

If R₄ is the unknown and R₁, R₂, R₃ are known (R₃ often a calibrated variable):

R₄ = R₃ × (R₂ / R₁) — rearrange to match your diagram’s knowns.

Worked example 1 — balance check. R₁ = 100 Ω, R₂ = 100 Ω, R₃ = 470 Ω, R₄ = 470 Ω.

R₁/R₂ = 1 and R₃/R₄ = 1 → balanced . Galvanometer reads zero.

Worked example 2 — find unknown. Bridge balanced with R₁ = 1 kΩ, R₂ = 4 kΩ, R₃ = 2.5 kΩ. Find Rₓ in the R₄ position using R₁/R₂ = R₃/Rₓ.

1/4 = 2.5 / Rₓ → Rₓ = 2.5 × 4 = 10 kΩ .

Worked example 3 — off balance (qualitative). If R₄ increases above the balance value, one mid-point potential shifts and detector current flows in a definite direction — used in null methods and in some sensor bridges where imbalance voltage is the output (strain gauges, RTD bridges — principles level).

Why bridges appear on Module 3

Accurate resistance measurement without relying only on a simple ohmmeter scale.

Null (balance) methods can be highly sensitive.

Links series/parallel divider ideas from §6.3 into a measurement instrument.

Temperature Coefficient Revisited

Temperature coefficient of resistance (α) quantifies how R changes with temperature. Section 6.1 used R_t = R₀[1 + α(Δt)] for approximately linear metallic behaviour.

  • Sign of α / device class R vs temperature Typical role
  • Positive (most metals, PTC) R up as T up Wire resistance rise; PTC protection / switching
  • Negative (many carbon compositions, NTC) R down as T up NTC sensing and compensation
  • Thermistors

A thermistor is a temperature-sensitive resistor, usually a semiconductor ceramic, with a large resistance change over a modest temperature span — far more sensitive than copper wire for the same ΔT.

NTC thermistors (Negative Temperature Coefficient)

Resistance falls as temperature rises .

Common for temperature measurement, inrush limiting (cold NTC starts high-R then falls), and compensation networks.

Worked idea: An NTC might be 10 kΩ at 25 °C and only a few kilohms at elevated bay temperature — a divider output voltage shifts measurably.

PTC thermistors (Positive Temperature Coefficient)

Resistance rises as temperature rises (often sharply near a transition for switching PTCs).

Used for over-temperature protection, self-resetting current limiting concepts, and heater regulation illustrations.

Thermistor limitations

Non-linear R–T curve (especially NTC) — calibration tables or linearising circuits needed for precision.

Self-heating : measurement current through the thermistor raises its own temperature and errors the reading if too large.

Tolerance and ageing — interchangeability poorer than precision wirewound resistors unless matched.

Limited power dissipation compared with large wirewound parts.

Aircraft training context: temperature probes and compensation networks in electronics bays are the practical cousins of the syllabus thermistor — Module 3 wants the NTC vs PTC definition and qualitative use, not a full air-data computer design.

  • VDRs — Voltage Dependent Resistors (Varistors)
  • A VDR (voltage-dependent resistor), often a varistor (for example metal-oxide varistor, MOV),

has resistance that falls sharply when voltage exceeds a threshold, clamping surges.

  • Condition Approximate behaviour
  • Below clamping / rated voltage High resistance — little leakage
  • Above threshold (surge) Resistance drops — conducts surge energy

Uses: transient suppression across supplies and signal lines (principles). Limitation: energy rating; repeated or huge surges degrade the device. Do not confuse VDRs with thermistors: one responds primarily to voltage , the other to temperature .

Fixed vs Variable Resistor Types — Roles and Limits

Type Adjustment / sensing Strengths Limitations

Fixed carbon / film None (set by manufacture) Cheap, colour-coded, wide ohm range Tolerance, drift, limited precision/power

  • Fixed wirewound None Higher power, stable Inductance (AC), cost, size
  • Potentiometer Manual voltage tap Convenient divider Wear, loading, resolution
  • Rheostat Manual series R Current control Heat in element, wear
  • Thermistor (NTC/PTC) Temperature → R High sensitivity Non-linearity, self-heating
  • VDR / varistor Voltage → R Surge clamping Energy limits, not a precision R

Light-dependent resistor (LDR) (if syllabus mentions) Light → R Simple sensing Slow, non-linear, ambient light errors

Fixed resistors are chosen when the circuit needs a stable, known R (within tolerance and TCR). Variable devices are chosen when the circuit must be adjusted or must respond to an environmental quantity. Mixing the categories on an exam stem — for example treating a thermistor as a precision fixed 1% metal-film stand-in — is a common mistake.

Putting Chapter 6 Together

Geometry and material set baseline R ( ρL/A , temperature).

Colour code and preferred values identify commercial fixed parts; wattage sets heat capability.

Series/parallel and pots/rheostats build and adjust networks.

Bridges measure R; thermistors and VDRs make R a sensor or protector.

Exam scenario — bridge with thermistor. One arm is an NTC. As bay temperature rises, NTC resistance falls, the bridge unbalances, and detector voltage indicates temperature — the same balance equation still defines the null point when you substitute the thermistor’s R at that temperature.

Exam scenario — PTC protection. A PTC in series with a load stays low-R when cool; on over-current/over-temperature it rises in R and throttles current.

Exam scenario — VDR across a DC bus. Normal 28 V operation sees high VDR resistance; a voltage spike drives the VDR into conduction to clamp the transient.

Master the balance ratio , the NTC/PTC definitions , and the fixed vs variable limitation table. That closes CAAS Module 3 topic 3.7 Resistance / resistor .