Study guide

14.1 Transformer Construction & Operation

CAAS SAR-66 AML Module 3 — Electrical Fundamentals Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 Current Exam Facts 1.2 Knowledge Levels & Study Approach for Module 3

2 Electron Theory & Static Electricity

2.1 Electron Theory & Atomic Structure 2.2 Conductors, Semiconductors & Insulators 2.3 Static Electricity, Coulomb's Law & Conduction

3 Terminology & Generation of Electricity

3.1 Electrical Terminology 3.2 Generation of Electricity

4 DC Sources of Electricity

4.1 Primary & Secondary Cells 4.2 Lead-Acid & Nickel-Cadmium Batteries 4.3 Series/Parallel Cells, Internal Resistance, Thermocouples & Photocells

5 DC Circuits

5.1 Ohm's Law 5.2 Kirchhoff's Voltage & Current Laws 5.3 Series/Parallel Networks & Supply Internal Resistance

6 Resistance & Resistors

6.1 Resistivity & Factors Affecting Resistance 6.2 Resistor Colour Code, Tolerance & Preferred Values 6.3 Series/Parallel Resistors, Potentiometers & Rheostats 6.4 Wheatstone Bridge, Thermistors & Temperature Coefficient

7 Power, Work & Energy

7.1 Power, Work & Energy Concepts 7.2 Power Dissipation & Calculations

8 Capacitance & Capacitors

8.1 Capacitor Operation & Factors Affecting Capacitance 8.2 Series/Parallel Capacitors & Types 8.3 RC Time Constants, Energy Storage & Testing

9 Magnetism

9.1 Theory of Magnetism & Magnetic Materials 9.2 Electromagnets & Hand Rules 9.3 MMF, Flux Density, Permeability, Hysteresis & Eddy Currents

10 Inductance & Inductors

10.1 Faraday's Law & Induced Voltage 10.2 Self & Mutual Inductance, Lenz's Law 10.3 Back EMF, Saturation & Inductor Applications

11 DC Motor/Generator Theory

11.1 Basic Motor & Generator Theory 11.2 DC Generators — Construction & Operation 11.3 DC Motors — Series, Shunt, Compound & Starter-Generators

12 AC Theory

12.1 Sinusoidal Waveforms — Phase, Period, Frequency 12.2 Peak, Average, RMS Values & Calculations 12.3 Non-Sinusoidal Waves & Single/Three-Phase Principles

13 R, L & C Circuits

13.1 Phase Relationships in R, L, C Circuits 13.2 Impedance, Phase Angle & Power Factor 13.3 True, Apparent & Reactive Power

14 Transformers

14.1 Transformer Construction & Operation 14.2 Losses, Efficiency, Load/No-Load & Turns Ratio 14.3 Three-Phase Transformers & Autotransformers

15 Filters & AC Generators

15.1 Filters — Low Pass, High Pass, Band Pass, Band Stop 15.2 AC Generator Principles & Construction 15.3 Star/Delta Connections & Permanent Magnet Generators

16 AC Motors

16.1 Synchronous & Induction Motors 16.2 Speed Control, Direction & Rotating Field Methods

14.1 Transformer Construction & Operation

Key Takeaways Explain This Topic AI

A transformer transfers AC electrical energy between circuits by mutual induction through a shared magnetic core — it does not work on steady DC

Primary winding connects to the source; secondary winding connects to the load; both link a laminated ferromagnetic core

Core-type windings surround the core legs; shell-type core surrounds the windings and is common in aircraft for low leakage

Induced secondary EMF follows Faraday’s law: e = −N (dΦ/dt); ideal voltage ratio equals the turns ratio

Polarity markings (dot convention / H1–X1) show which terminals have the same instantaneous polarity for additive or subtractive connection

Last updated: July 2026

14.1 Transformer Construction & Operation

Quick Answer: A transformer couples AC circuits by mutual induction . AC in the primary produces changing core flux that induces EMF in the secondary . Cores are laminated silicon steel (core-type or shell-type). Polarity marks identify terminals that go positive together so windings can be phased correctly.

CAAS SAR-66 Module 3 topic 3.15 Transformers follows R, L, and C circuits (3.14) and precedes filters (3.16). Aircraft buses are typically 115 V AC / 400 Hz ; many loads need other AC voltages (instrument lighting, radar supplies, specialty AC). Transformers provide those levels without sliding contacts or continuous mechanical conversion. This section builds construction and operating vocabulary before losses, turns-ratio maths, and three-phase/autotransformer variants.

What a Transformer Is

A transformer is a static electromagnetic device with:

A primary winding — connected to the AC source.

One or more secondary windings — connected to the load(s).

A ferromagnetic core — low-reluctance path guiding nearly all flux from primary to secondary.

There is no conductive connection between isolated primary and secondary in a conventional two-winding transformer (contrast autotransformers in Section 14.3). Energy transfers magnetically.

  • Part Role
  • Primary (Np turns) Creates alternating magnetomotive force and core flux
  • Core Concentrates and guides mutual flux Φ
  • Secondary (Ns turns) Flux change induces secondary EMF
  • Insulation / varnish Separates turns and laminations; sets voltage rating
  • Tank / enclosure (when used) Mechanical protection; sometimes oil cooling on ground units

Aircraft context: Airborne units are usually dry, compact, and sized for 400 Hz . Higher frequency means less core mass for a given flux-density limit than a 50/60 Hz utility transformer of similar power — a direct weight benefit.

  • Operating Principle — Mutual Induction
  • Faraday and Lenz

When primary current is alternating, core flux Φ is alternating. Faraday’s law for a coil of N turns:

e = −N (dΦ / dt)

The secondary sees essentially the same mutual flux (ideal assumption), so:

es = −Ns (dΦ / dt) and ep ≈ −Np (dΦ / dt)

Hence for sinusoidal excitation the RMS magnitudes satisfy:

  • Vp / Vs ≈ Np / Ns
  • (Detailed turns-ratio and current relationships are Section 14.2.)

Lenz’s law sets the polarity of the induced EMF so that secondary current (when a load is connected) produces flux opposing the change that created it. That opposition appears at the primary as an increased primary current — the mechanism of power transfer from source to load.

Why Steady DC Does Not Transform

Steady DC primary current produces constant flux (after magnetisation settles). Then dΦ/dt = 0 , so secondary induced EMF is zero. A DC step transient can induce a pulse, but continuous transformation of power requires changing flux — hence AC only for normal transformer action. Applying DC to a primary also risks high magnetising current and core saturation because winding resistance alone limits current once inductance’s opposing effect dies away.

Worked idea — 400 Hz vs 50 Hz. For the same peak flux density B and same core area A, Φ_peak = B A. Induced EMF magnitude scales with f × N × Φ_peak . At 400 Hz versus 50 Hz (8× frequency), the same EMF needs roughly 1/8 the core volume product (N A) if B is held similar — the engineering reason aircraft magnetics can be small and light.

  • Core Construction
  • Material

Cores use silicon steel (typically a few percent silicon) to raise electrical resistivity (helps eddy-current suppression — Section 14.2) while keeping high permeability and a narrow hysteresis loop. Soft magnetic behaviour (low coercivity) reduces hysteresis heating each AC cycle.

Laminations

The core is not a solid block. It is stacked thin laminations (often ~0.3–0.5 mm class for power magnetics), each coated with insulating varnish or oxide. Laminations lie parallel to the flux path so magnetic reluctance stays low, while eddy-current loops are broken across the stack thickness. At 400 Hz, eddy and hysteresis design is especially important because both core-loss mechanisms rise with frequency.

Core-Type vs Shell-Type

  • Feature Core-type Shell-type
  • Geometry Windings surround core legs Core surrounds central winding limb
  • Flux path Mainly single loop through both limbs Flux divides in two parallel return paths
  • Leakage Generally higher leakage tendency Lower leakage; windings better enclosed
  • Insulation Relatively easy access to windings Excellent mechanical support
  • Aviation use Used where layout suits Very common for compact aircraft units

Shell-type construction keeps primary and secondary close and nested, reducing flux leakage (flux that fails to link both windings). Module 3 expects you to recognise both names and that shell construction improves coupling.

Windings and Insulation

Windings are insulated copper (or sometimes aluminium on large ground units). Cross-section follows current: the low-voltage, high-current winding uses thicker conductors. Layers and bobbins set creepage distance for the voltage class. Multiple secondaries can share one primary (e.g., several instrument supplies).

Step-down / step-up naming refers to voltage: Ns < Np → step-down; Ns > Np → step-up. Current moves the opposite way for roughly constant VA (Section 14.2).

Polarity Markings

Polarity answers: which secondary terminal is instantaneously positive when a chosen primary terminal is positive?

Dot convention

Dots (or equivalent marks) on one primary and one secondary terminal mean those terminals have the same instantaneous polarity . If both dotted ends are taken as “starts,” voltages are in phase in the additive sense used on diagrams.

Additive and subtractive connection

When windings are series-connected for higher voltage:

Additive (boost): connect so instantaneous voltages add — join unmarked (or opposite-polarity) ends appropriately per the marking standard so the series voltage is |Vp| + |Vs| (for similarly rated senses).

Subtractive (buck): reverse relative sense so voltages oppose — series voltage is the difference.

Wrong polarity on paralleled secondaries causes circulating current and damage. Wrong boost/buck on series taps yields unexpected voltage.

Alphanumeric marks (H and X)

Many power transformers use H1, H2… on the high-voltage winding and X1, X2… on the low-voltage winding. A common subtractive standard places H1 and X1 so that when H1 is instantaneously positive, X1 is also positive (same instantaneous polarity). Always follow the nameplate/diagram for the unit in hand — Module 3 cares that you know markings exist to show in-phase terminals , not that you memorise every national marking table.

Worked polarity check (conceptual). Primary H1–H2 driven from 115 V AC. Secondary X1–X2. With H1 and X1 same-polarity marked, a voltmeter from H1 to X1 (with an appropriate series connection test per training procedure) reads near the difference of the two winding voltages when windings are connected subtractively for the test, versus near the sum for additive — the classic polarity-test idea used in training shops.

Ideal Transformer Snapshot

For teaching, the ideal transformer assumes:

  • Zero winding resistance
  • Zero core loss
  • Infinite permeability (negligible magnetising current)
  • Perfect flux linkage (no leakage)

Then Vp/Vs = Np/Ns = Is/Ip and Pin = Pout . Real units deviate (Section 14.2), but ideal laws are the exam calculation baseline.

Magnetising Current (Qualitative)

Even with secondary open, a small no-load / magnetising current flows in the primary to establish core flux and supply core losses. It is largely reactive (lags voltage ≈ 90° in the simple model) plus a small in-phase component for core loss. Do not confuse no-load current with load current — load current appears when the secondary delivers power.

Summary for Syllabus 3.15 Construction

  • Idea Exam takeaway
  • Energy transfer Mutual induction via changing core flux
  • DC No continuous transformer action
  • Core Laminated silicon steel; core- or shell-type
  • 400 Hz Smaller/lighter cores than 50/60 Hz for similar power
  • Polarity Dots / H–X marks = same instantaneous polarity

Master primary/secondary roles, why laminations exist at a construction level, core vs shell, and polarity marks. Section 14.2 then quantifies turns ratio, losses, load vs no-load, and efficiency.