Study guide

2.1 Domestic Wiring Systems, Cables, and Conduits

EMA Electrician Licence Written Assessment Study Guide Singapore

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Assessment Overview, Electricity Act and Regulations

1.1 Assessment Structure, Eligibility, Fees, and Application Process 1.2 Legislative Framework and Electricity Act Overview (Part 9) 1.3 Electrical Workers Regulations and LEW Classes 1.4 Scope of Work and Responsibilities of a Licensed Electrician 1.5 Electrical Installations Regulations and Compliance Requirements 1.6 Notification, Connection, Modification, and Inspection Duties 1.7 Offences, Penalties, Disciplinary Actions, and Licence Renewal

2 Chapter 2: Domestic Electrical Installations (SS 638)

2.1 Domestic Wiring Systems, Cables, and Conduits 2.2 Consumer Units and Distribution Board (DB) Layouts 2.3 Final Circuits: Lighting, Radial, and Ring Final Socket Circuits 2.4 Mandatory 30 mA RCD/RCCB Protection and Isolation 2.5 Cable Colour Coding, Identification, and Accessories

3 Chapter 3: Industrial Electrical Installations (SS 638)

3.1 Industrial Low-Voltage (LV) Distribution and Sub-Switchboards 3.2 Motor Control Circuits, Starters, and Overload Protection 3.3 Industrial Wiring Systems: Trunking, Tray, Ladder, and Armoured Cables 3.4 Industrial Load Segregation, Phase Balancing, and Emergency Stopping 3.5 Industrial Switchgear, Circuit Breakers (MCB, MCCB), and Fuses 3.6 Motor Troubleshooting, Sequential Starting, and Programmable Logic Controllers (PLC)

4 Chapter 4: Electrical Principles — AC/DC Supplies, Three-Phase Power, and Power Quality

4.1 AC and DC Supply Fundamentals: Circuit Laws, RMS Values, and Singapore Voltage Levels 4.2 Three-Phase Relationships and Real, Apparent, and Reactive Power 4.3 Power Factor Correction, Harmonics, and Power Quality

5 Chapter 5: Protection Against Electric Shock and Earthing

5.1 Fundamentals of Electric Shock: Basic Protection and Fault Protection 5.2 Earthing Systems in Singapore: TN-S and TT Arrangements 5.3 Touch Voltage, Protective Conductor Sizing, and Main Earthing Terminals 5.4 Residual Current Devices (RCD/RCCB), Earth Fault Protection, and Equipotential Bonding

6 Chapter 6: Installation Design, Single-Line Diagrams (SLD), and Cable Sizing

6.1 Single-Line Diagram (SLD) Preparation, Symbols, and Standard Layouts 6.2 Maximum Demand Calculation and Diversity Factors for ≤45 kVA 6.3 Cable Selection, Current-Carrying Capacity, and Correction Factors 6.4 Voltage Drop Calculations and Circuit Segregation Rules

7 Chapter 7: Testing and Commissioning

7.1 Inspection and Testing Sequence Overview and Visual Inspection 7.2 Continuity Testing of Protective and Equipotential Conductors 7.3 Insulation Resistance Testing and Polarity Verification 7.4 Earth Fault Loop Impedance (Zs), RCD Testing, and Post-Turn-On Checks

8 Chapter 8: Temporary Electrical Installations (SS 650)

8.1 SS 650 Part 1: Construction Site Temporary Electrical Supply 8.2 SS 650 Part 2: Festive Lighting, Trade Fairs, and Exhibition Supplies 8.3 Temporary Generators, Statement of Approval (SOA), and Safety Inspections

2.1 Domestic Wiring Systems, Cables, and Conduits

Key Takeaways Explain This Topic AI

SS 638 (Code of Practice for Electrical Installations) governs domestic electrical installations in Singapore, setting mandatory technical standards for low-voltage residential wiring.

Single-core PVC insulated copper cables (450/750 V) and multi-core PVC/PVC cables (600/1000 V) complying with SS 358 and BS 6004 form the core of domestic wiring systems.

Conduits and mini-trunking must strictly observe the 40% maximum space factor rule to ensure adequate thermal dissipation and prevent mechanical damage during cable drawing.

Wall chasing in Housing & Development Board (HDB) residential flats is strictly regulated: chasing is permitted only on non-structural masonry, must run vertically, and is limited in depth.

Last updated: August 2026

2.1 Domestic Wiring Systems, Cables, and Conduits

In Singapore, low-voltage domestic electrical installations are designed, installed, and tested in accordance with SS 638: Code of Practice for Electrical Installations (formerly designated as CP 5, aligned with the international standard BS 7671). The statutory regulatory authority, the Energy Market Authority (EMA) , mandates that all electrical work in residential premises—including Housing & Development Board (HDB) flats, private condominiums, and landed housing—must be executed or directly supervised by a Licensed Electrical Worker (LEW) holding an appropriate licence grade (Licensed Electrician, Electrical Technician, or Electrical Engineer).

Domestic wiring systems must provide long-term operational reliability, mechanical robustness, overcurrent protection, and complete safety against thermal fire hazards and electric shock. Understanding the technical specifications of conductors, insulation materials, wiring enclosures, and structural mounting guidelines is essential for candidates preparing for the EMA Electrician Licence Written Assessment.

1. Cable Types and Specifications in Domestic Wiring

The vast majority of domestic final circuits and sub-mains in Singapore utilize copper conductors insulated and sheathed with Polyvinyl Chloride (PVC) or Cross-linked Polyethylene (XLPE). Under Regulation 14 of the Electricity (Electrical Installations) Regulations , no person may use an electricity cable with aluminium conductors in any electrical installation used wholly or partly for domestic purposes — a prohibition rooted in concerns regarding galvanic corrosion, differential thermal expansion, and terminal loosening at accessories.

Standard Cable Classifications

Single-Core PVC Insulated Non-Sheathed Cables (SS 358 / BS 6004)

Voltage Rating: 450/750 V.

Conductor: High-conductivity plain annealed stranded or solid copper (Class 1 solid or Class 2 stranded).

Application: Drawn into high-impact rigid PVC or galvanised steel conduits, surface PVC trunking, or concealed conduits within walls and concrete slabs.

Operating Temperature: Standard continuous maximum conductor operating temperature of 70°C .

Multi-Core PVC Insulated and PVC Sheathed Cables (PVC/PVC)

Voltage Rating: 600/1000 V (or 300/500 V for lighter domestic flexes).

Construction: Two, three, or four PVC-insulated copper cores enclosed within an outer protective PVC sheath.

Application: Surface wiring, sub-main feeds from meter compartments to distribution boards (DBs), and clipped-direct runs above false ceilings.

Low Smoke Zero Halogen (LSZH) Cables

Construction: Thermosetting or thermoplastic insulation that emits minimal smoke and virtually zero halogen gases when exposed to fire.

Application: Increasingly specified in modern high-rise residential buildings, common corridors, and emergency exit routes to mitigate smoke inhalation risks during building fires.

  • Cable Type Standard Reference Voltage Rating Max Conductor Temp Common Domestic Application
  • Single-Core PVC SS 358 / BS 6004 450/750 V 70°C Circuit wiring inside conduit/trunking
  • Multi-Core PVC/PVC SS 358 / BS 6004 600/1000 V 70°C Surface wiring, sub-mains, outdoor feeds
  • Flexible PVC Cable SS 358 / BS 6500 300/500 V 70°C Appliance connections, pendant lights
  • XLPE/LSZH SS 271 / BS 7211 600/1000 V 90°C High-rise residential sub-mains
  • 2. Current-Carrying Capacity and Thermal Correction Factors

The current-carrying capacity ( I z I_z I z ​ ) of a cable represents the maximum continuous current that can flow through its conductors without exceeding the rated insulation temperature (70°C for standard PVC). In accordance with SS 638 Appendix 4, the tabulated current rating ( I t I_t I t ​ ) must be adjusted by applying correction factors for ambient temperature, grouping, and thermal insulation. I z = I t × C a × C g × C i × C f I_z = I_t \times C_a \times C_g \times C_i \times C_f I z ​ = I t ​ × C a ​ × C g ​ × C i ​ × C f ​

Where:

C a C_a C a ​ (Ambient Temperature Correction Factor): The standard reference ambient temperature in Singapore is 30°C for air and 15°C for underground soil. When cables are installed in unventilated roof spaces or hot ceiling voids where ambient temperatures reach 40°C or 50°C, C a C_a C a ​ reduces the current rating ( C a = 0.87 C_a = 0.87 C a ​ = 0.87 at 40°C for PVC insulation).

C g C_g C g ​ (Grouping Correction Factor): When multiple circuits are enclosed together in the same conduit or trunking, mutual heating increases conductor temperatures. For example, grouping 4 single-phase circuits (8 loaded conductors) in a single trunking reduces the effective capacity by a factor of C g ≈ 0.65 C_g \approx 0.65 C g ​ ≈ 0.65 .

C i C_i C i ​ (Thermal Insulation Factor): If a cable is totally surrounded by thermal insulation (e.g., in dry-wall partitions), C i = 0.50 C_i = 0.50 C i ​ = 0.50 , effectively halving its continuous current capacity.

C f C_f C f ​ (BS 3036 Semi-enclosed Fuse Factor): Applies only if semi-enclosed re-wireable fuses are used ( C f = 0.725 C_f = 0.725 C f ​ = 0.725 ). In modern domestic installations utilizing Miniature Circuit Breakers (MCBs), C f = 1.0 C_f = 1.0 C f ​ = 1.0 .

Design Rule for Overcurrent Protection

For any final circuit, the nominal operating current ( I b I_b I b ​ ), the rated current of the protective device ( I n I_n I n ​ ), and the adjusted continuous current capacity of the cable ( I z I_z I z ​ ) must satisfy the fundamental inequality: I b ≤ I n ≤ I z I_b \le I_n \le I_z I b ​ ≤ I n ​ ≤ I z ​

Furthermore, the current causing effective operation of the protective device ( I 2 I_2 I 2 ​ ) must not exceed 1.45 × I z 1.45 \times I_z 1.45 × I z ​ . For standard MCBs complying with SS 229 / IEC 60898, this condition is automatically satisfied when I n ≤ I z I_n \le I_z I n ​ ≤ I z ​ .

3. Wiring Enclosures: Conduits and Surface Trunking

Mechanical protection against physical damage, moisture ingress, and environmental degradation is achieved using rigid conduits or surface mini-trunking systems.

High-Impact Rigid PVC Conduit (SS 213 / BS EN 61386)

High-impact unplasticised PVC conduits are non-conductive, corrosion-resistant, and self-extinguishing.

Standard nominal outer diameters used in domestic premises are 20 mm and 25 mm .

Bending is achieved cold using an internal steel bending spring or warm using a hot-air blow torch.

Conduit expansion joints must be installed where structural expansion joints are crossed.

Surface PVC Mini-Trunking

Rigid PVC surface trunking (typically 16 × 25 mm 16 \times 25\text{ mm} 16 × 25 mm , 25 × 38 mm 25 \times 38\text{ mm} 25 × 38 mm , or 50 × 50 mm 50 \times 50\text{ mm} 50 × 50 mm ) with snap-on covers is widely utilized in HDB apartment retrofitting and rewiring to avoid heavy wall chasing.

Accessories (junction boxes, switch boxes, socket boxes) must integrate seamlessly with trunking entry knockouts to preserve IP20 enclosure protection.

The 40% Maximum Space Factor Rule

To ensure cables can be drawn into a conduit or trunking without excessive mechanical tension, stretching of copper strands, or tearing of PVC insulation, and to permit adequate air circulation for cooling, SS 638 mandates a maximum space factor of 40% . Space Factor = ∑ Total Cross-Sectional Area of Cables (including insulation) Internal Cross-Sectional Area of Conduit or Trunking × 100 % ≤ 40 % \text{Space Factor} = \frac{\sum \text{Total Cross-Sectional Area of Cables (including insulation)}}{\text{Internal Cross-Sectional Area of Conduit or Trunking}} \times 100\% \le 40\% Space Factor = Internal Cross-Sectional Area of Conduit or Trunking ∑ Total Cross-Sectional Area of Cables (including insulation) ​ × 100% ≤ 40%

For practical conduit sizing, SS 638 provides standardized Cable Factor Tables . Each cable size is assigned a specific factor (e.g., 1.5 mm 2 1.5\text{ mm}^2 1.5 mm 2 solid cable factor = 22; 2.5 mm 2 2.5\text{ mm}^2 2.5 mm 2 solid cable factor = 30). The sum of cable factors for all conductors drawn into a run must not exceed the Conduit Factor established for the length of run and number of bends. Conduit Capacity Example (20 mm vs 25 mm Rigid PVC Conduit):

- Straight run up to 3 meters (Conduit Factor for 20 mm = 460):

Maximum 2.5 mm² single-core PVC cables = 460 / 30 = 15 conductors.

- Run of 5 meters with two 90° bends (Conduit Factor for 20 mm = 290):

Maximum 2.5 mm² single-core PVC cables = 290 / 30 = 9 conductors.

4. HDB Structural Wall-Chasing Regulations

When installing concealed conduits in residential apartments governed by the Housing & Development Board (HDB), strict structural safety limits apply. Unauthorized or excessively deep chasing can severely weaken load-bearing walls and compromise building safety.

Prohibited Chasing Locations:

Structural Concrete Columns and Beams: Absolutely NO chasing, drilling, or cutting into reinforced concrete (RC) structural columns, tie beams, or shear walls is permitted under any circumstances.

Pre-cast RC Wall Panels: Chasing into load-bearing pre-cast concrete structural panels is strictly illegal.

Permitted Chasing Guidelines (Non-Structural Brick or Block Walls):

Direction of Chasing: All chases must be executed vertically . Horizontal chasing across masonry walls is strictly restricted to short runs under 300 mm because horizontal cuts significantly reduce the lateral load capacity of brickwork.

Maximum Chase Depth: The depth of a vertical chase must not exceed 25 mm or 1/3 of the wall thickness , whichever is less.

Protective Capping: Chased conduits must be covered with galvanized steel capping or heavy-duty PVC channeling prior to plastering to guard against accidental nail or screw penetration during home fitting installations.

Summary of Domestic Cable Sizes and Applications

  • Conductor Size Cable Type Protective MCB Rating Typical Domestic Final Circuit Application
  • 1.5 mm² Single-core PVC 6A or 10A (Type B) Domestic lighting circuits, ceiling fans, doorbell supplies

2.5 mm² Single-core PVC 20A (Type B/C) 20A Radial socket circuits (Floor area ≤ 50 m 2 \le 50\text{ m}^2 ≤ 50 m 2 )

2.5 mm² Single-core PVC 32A (Type B) Ring final socket circuits (Floor area ≤ 100 m 2 \le 100\text{ m}^2 ≤ 100 m 2 )

  • 2.5 mm² Single-core PVC 16A or 20A (Type C) Dedicated split-unit air-conditioner radial circuit
  • 4.0 mm² Single-core PVC 20A or 32A (Type B/C) Dedicated Instantaneous Water Heater circuit (up to 4.5 kW)
  • 6.0 mm² Single-core / Multi-core 32A or 40A (Type B/C) Electric hob / oven circuit, high-power water heater
  • 10.0 / 16.0 mm² Multi-core PVC/PVC 40A or 63A DP Main Sub-main feed from meter board to domestic Consumer Unit

Loading diagram... Domestic Wiring Installation & Enclosure Selection Workflow