Study guide
4.2 Three-Phase Relationships and Real, Apparent, and Reactive Power
EMA Electrician Licence Written Assessment Study Guide Singapore
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Assessment Overview, Electricity Act and Regulations
1.1 Assessment Structure, Eligibility, Fees, and Application Process 1.2 Legislative Framework and Electricity Act Overview (Part 9) 1.3 Electrical Workers Regulations and LEW Classes 1.4 Scope of Work and Responsibilities of a Licensed Electrician 1.5 Electrical Installations Regulations and Compliance Requirements 1.6 Notification, Connection, Modification, and Inspection Duties 1.7 Offences, Penalties, Disciplinary Actions, and Licence Renewal
2 Chapter 2: Domestic Electrical Installations (SS 638)
2.1 Domestic Wiring Systems, Cables, and Conduits 2.2 Consumer Units and Distribution Board (DB) Layouts 2.3 Final Circuits: Lighting, Radial, and Ring Final Socket Circuits 2.4 Mandatory 30 mA RCD/RCCB Protection and Isolation 2.5 Cable Colour Coding, Identification, and Accessories
3 Chapter 3: Industrial Electrical Installations (SS 638)
3.1 Industrial Low-Voltage (LV) Distribution and Sub-Switchboards 3.2 Motor Control Circuits, Starters, and Overload Protection 3.3 Industrial Wiring Systems: Trunking, Tray, Ladder, and Armoured Cables 3.4 Industrial Load Segregation, Phase Balancing, and Emergency Stopping 3.5 Industrial Switchgear, Circuit Breakers (MCB, MCCB), and Fuses 3.6 Motor Troubleshooting, Sequential Starting, and Programmable Logic Controllers (PLC)
4 Chapter 4: Electrical Principles — AC/DC Supplies, Three-Phase Power, and Power Quality
4.1 AC and DC Supply Fundamentals: Circuit Laws, RMS Values, and Singapore Voltage Levels 4.2 Three-Phase Relationships and Real, Apparent, and Reactive Power 4.3 Power Factor Correction, Harmonics, and Power Quality
5 Chapter 5: Protection Against Electric Shock and Earthing
5.1 Fundamentals of Electric Shock: Basic Protection and Fault Protection 5.2 Earthing Systems in Singapore: TN-S and TT Arrangements 5.3 Touch Voltage, Protective Conductor Sizing, and Main Earthing Terminals 5.4 Residual Current Devices (RCD/RCCB), Earth Fault Protection, and Equipotential Bonding
6 Chapter 6: Installation Design, Single-Line Diagrams (SLD), and Cable Sizing
6.1 Single-Line Diagram (SLD) Preparation, Symbols, and Standard Layouts 6.2 Maximum Demand Calculation and Diversity Factors for ≤45 kVA 6.3 Cable Selection, Current-Carrying Capacity, and Correction Factors 6.4 Voltage Drop Calculations and Circuit Segregation Rules
7 Chapter 7: Testing and Commissioning
7.1 Inspection and Testing Sequence Overview and Visual Inspection 7.2 Continuity Testing of Protective and Equipotential Conductors 7.3 Insulation Resistance Testing and Polarity Verification 7.4 Earth Fault Loop Impedance (Zs), RCD Testing, and Post-Turn-On Checks
8 Chapter 8: Temporary Electrical Installations (SS 650)
8.1 SS 650 Part 1: Construction Site Temporary Electrical Supply 8.2 SS 650 Part 2: Festive Lighting, Trade Fairs, and Exhibition Supplies 8.3 Temporary Generators, Statement of Approval (SOA), and Safety Inspections
4.2 Three-Phase Relationships and Real, Apparent, and Reactive Power
Key Takeaways Explain This Topic AI
In a star (Y) system the line voltage is √3 times the phase voltage (400 V / 230 V) while line current equals phase current; in a delta (Δ) system line voltage equals phase voltage while line current is √3 times phase current.
Three-phase power formulas: P = √3 × VL × IL × cos φ (kW), Q = √3 × VL × IL × sin φ (kVAr), S = √3 × VL × IL (kVA); single-phase: P = V × I × cos φ.
The power triangle links real, reactive, and apparent power: S² = P² + Q², with power factor cos φ = P / S.
A 400 V, 2 kW, 3-phase motor at 0.8 power factor draws a running current of 2000 / (√3 × 400 × 0.8) = 3.61 A, and 6–8 times that (≈22–29 A) when started direct-on-line.
Cables are sized for running current, not starting current, because DOL inrush is momentary; protective devices are selected to ride through the inrush without tripping.
Last updated: August 2026
4.2 Three-Phase Relationships and Real, Apparent, and Reactive Power
Quick Summary: Three-phase questions are guaranteed marks in Sections C and D. Fix the √3 relationships (star: V L = 3 V p h V_L = \sqrt{3}\, V_{ph} V L = 3 V p h ; delta: I L = 3 I p h I_L = \sqrt{3}\, I_{ph} I L = 3 I p h ), the √3 power formulas , and the power triangle ( S 2 = P 2 + Q 2 S^2 = P^2 + Q^2 S 2 = P 2 + Q 2 , cos ϕ = P / S \cos\phi = P/S cos ϕ = P / S ) in memory, and every motor-current, maximum-demand, and cable-sizing calculation in this guide becomes mechanical.
1. Star (Y) and Delta (Δ) Relationships
Quantity Star (Y) Connection Delta (Δ) Connection
Line vs phase voltage V L = 3 V p h V_L = \sqrt{3}\, V_{ph} V L = 3 V p h (400 V = √3 × 230 V) V L = V p h V_L = V_{ph} V L = V p h
Line vs phase current I L = I p h I_L = I_{ph} I L = I p h I L = 3 I p h I_L = \sqrt{3}\, I_{ph} I L = 3 I p h
Typical use Distribution with neutral (3-phase 4-wire), motor star starting Motor windings in run mode, balanced 3-wire loads
Singapore's 400 V / 230 V system is exactly this star relationship: each phase-to-neutral voltage is 230 V, and 3 × 230 = 400 V \sqrt{3} \times 230 = 400\text{ V} 3 × 230 = 400 V between any two lines.
2. Single-Phase and Three-Phase Power Formulas
Single-phase: P = V × I × cos ϕ P = V \times I \times \cos\phi P = V × I × cos ϕ ; S = V × I S = V \times I S = V × I .
Three-phase (star or delta, using line values): P = 3 × V L × I L × cos ϕ S = 3 × V L × I L I L = P 3 V L cos ϕ P = \sqrt{3} \times V_L \times I_L \times \cos\phi \qquad S = \sqrt{3} \times V_L \times I_L \qquad I_L = \frac{P}{\sqrt{3}\, V_L \cos\phi} P = 3 × V L × I L × cos ϕ S = 3 × V L × I L I L = 3 V L cos ϕ P
Sanity check: 45 kVA at 400 V gives I L = 45,000 / ( 3 × 400 ) = 64.95 A I_L = 45{,}000 / (\sqrt{3} \times 400) = 64.95\text{ A} I L = 45 , 000/ ( 3 × 400 ) = 64.95 A — the Electrician licence ceiling expressed in current terms (Chapter 1).
3. Real, Apparent, and Reactive Power — The Power Triangle
Real (active) power P P P (kW): does useful work (heat, torque, light).
Reactive power Q Q Q (kVAr): sustains magnetic fields in motors and transformers; oscillates between source and load without doing useful work.
Apparent power S S S (kVA): the vector sum that the supply and cables must actually carry. S 2 = P 2 + Q 2 cos ϕ = P S tan ϕ = Q P S^2 = P^2 + Q^2 \qquad \cos\phi = \frac{P}{S} \qquad \tan\phi = \frac{Q}{P} S 2 = P 2 + Q 2 cos ϕ = S P tan ϕ = P Q
Cables, breakers, and transformers are thermally limited by current , hence by S S S — two loads with equal kW but different power factors draw different currents. This is why the licence scope is defined in kVA , not kW.
4. Worked Motor Calculations (EMA Sample-Question Style)
Question (from EMA's published sample list): for a 3-phase 400 V, 2 kW motor with power factor 0.8, find (a) the running current, (b) the direct-on-line starting current, and (c) whether the cable is sized for starting or running current.
(a) Running current: I r u n = P 3 × V L × cos ϕ = 2,000 1.732 × 400 × 0.8 = 2,000 554.3 = 3.61 A I_{run} = \frac{P}{\sqrt{3} \times V_L \times \cos\phi} = \frac{2{,}000}{1.732 \times 400 \times 0.8} = \frac{2{,}000}{554.3} = 3.61\text{ A} I r u n = 3 × V L × cos ϕ P = 1.732 × 400 × 0.8 2 , 000 = 554.3 2 , 000 = 3.61 A
(b) DOL starting current: induction motors draw 6–8 × full-load current at standstill (Chapter 3.2): I s t a r t ≈ 6 × 3.61 ≈ 21.7 A to 8 × 3.61 ≈ 28.9 A I_{start} \approx 6 \times 3.61 \approx 21.7\text{ A} \;\text{to}\; 8 \times 3.61 \approx 28.9\text{ A} I s t a r t ≈ 6 × 3.61 ≈ 21.7 A to 8 × 3.61 ≈ 28.9 A
(c) Cable sizing basis: the cable is sized for the running current (with correction factors), not the starting current — the inrush lasts only seconds, and the protective device is chosen (Type C/D curve or a suitable fuse) to withstand it without tripping. The overload relay, set at 1.0 × I F L C 1.0 \times I_{FLC} 1.0 × I F L C (or 0.58 × I F L C 0.58 \times I_{FLC} 0.58 × I F L C inside a star-delta loop), protects the motor thermally during run.
Efficiency variant: if the 2 kW is shaft (output) power with efficiency η = 0.85 \eta = 0.85 η = 0.85 , first convert to input: P i n = 2,000 / 0.85 = 2,353 W P_{in} = 2{,}000 / 0.85 = 2{,}353\text{ W} P in = 2 , 000/0.85 = 2 , 353 W , then I r u n = 2,353 / 554.3 = 4.25 A I_{run} = 2{,}353 / 554.3 = 4.25\text{ A} I r u n = 2 , 353/554.3 = 4.25 A . Read whether the question gives output or input power — EMA long questions mark the distinction.
5. Per-Phase Analysis and Metering
For unbalanced loads, compute each phase separately: per-phase P p h = V p h × I p h × cos ϕ = 230 × I p h × cos ϕ P_{ph} = V_{ph} \times I_{ph} \times \cos\phi = 230 \times I_{ph} \times \cos\phi P p h = V p h × I p h × cos ϕ = 230 × I p h × cos ϕ , then sum the three phases. Metering follows the same structure: whole-current kWh meters connect directly for small loads, while CT-operated meters (e.g., 100/5 A) step down larger currents — the SLD must show the arrangement of protective devices before and after the meter (Chapter 6.1).
6. Reverse Calculations and Common Three-Phase Traps
Written-test long questions frequently work backwards from current to power. Example: a balanced 3-phase heater bank draws 20 A per line at unity power factor from 400 V. Its real power is P = 3 × 400 × 20 × 1.0 = 13,856 W ≈ 13.9 kW P = \sqrt{3} \times 400 \times 20 \times 1.0 = 13{,}856\text{ W} \approx 13.9\text{ kW} P = 3 × 400 × 20 × 1.0 = 13 , 856 W ≈ 13.9 kW , and its apparent power is S = 3 × 400 × 20 = 13.9 kVA S = \sqrt{3} \times 400 \times 20 = 13.9\text{ kVA} S = 3 × 400 × 20 = 13.9 kVA (identical because cos ϕ = 1 \cos\phi = 1 cos ϕ = 1 ).
Traps EMA Examiners Exploit
Forgetting √3 in 3-phase work: using P = V L × I L P = V_L \times I_L P = V L × I L instead of 3 × V L × I L \sqrt{3} \times V_L \times I_L 3 × V L × I L underestimates power by 42%. If an answer looks 1.73× too small, the √3 was dropped.
Mixing line and phase values in delta loads: a delta motor winding sees the full 400 V, but its winding current is only I L / 3 I_L/\sqrt{3} I L / 3 — the basis of the 0.58 × FLC overload-relay rule (Chapter 3.2).
Using 230 V with √3: the √3 formulas require the line-to-line voltage (400 V); using 230 V with √3 produces line/phase-confused answers (e.g., 26 kVA instead of 45 kVA).
kW versus kVA confusion: licence scope, breaker thermal duty, and supply capacity are kVA (current-based); appliance nameplates are usually kW . Convert through cos ϕ \cos\phi cos ϕ before comparing them.