Study guide

3.6 Motor Troubleshooting, Sequential Starting, and Programmable Logic Controllers (PLC)

EMA Electrician Licence Written Assessment Study Guide Singapore

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Assessment Overview, Electricity Act and Regulations

1.1 Assessment Structure, Eligibility, Fees, and Application Process 1.2 Legislative Framework and Electricity Act Overview (Part 9) 1.3 Electrical Workers Regulations and LEW Classes 1.4 Scope of Work and Responsibilities of a Licensed Electrician 1.5 Electrical Installations Regulations and Compliance Requirements 1.6 Notification, Connection, Modification, and Inspection Duties 1.7 Offences, Penalties, Disciplinary Actions, and Licence Renewal

2 Chapter 2: Domestic Electrical Installations (SS 638)

2.1 Domestic Wiring Systems, Cables, and Conduits 2.2 Consumer Units and Distribution Board (DB) Layouts 2.3 Final Circuits: Lighting, Radial, and Ring Final Socket Circuits 2.4 Mandatory 30 mA RCD/RCCB Protection and Isolation 2.5 Cable Colour Coding, Identification, and Accessories

3 Chapter 3: Industrial Electrical Installations (SS 638)

3.1 Industrial Low-Voltage (LV) Distribution and Sub-Switchboards 3.2 Motor Control Circuits, Starters, and Overload Protection 3.3 Industrial Wiring Systems: Trunking, Tray, Ladder, and Armoured Cables 3.4 Industrial Load Segregation, Phase Balancing, and Emergency Stopping 3.5 Industrial Switchgear, Circuit Breakers (MCB, MCCB), and Fuses 3.6 Motor Troubleshooting, Sequential Starting, and Programmable Logic Controllers (PLC)

4 Chapter 4: Electrical Principles — AC/DC Supplies, Three-Phase Power, and Power Quality

4.1 AC and DC Supply Fundamentals: Circuit Laws, RMS Values, and Singapore Voltage Levels 4.2 Three-Phase Relationships and Real, Apparent, and Reactive Power 4.3 Power Factor Correction, Harmonics, and Power Quality

5 Chapter 5: Protection Against Electric Shock and Earthing

5.1 Fundamentals of Electric Shock: Basic Protection and Fault Protection 5.2 Earthing Systems in Singapore: TN-S and TT Arrangements 5.3 Touch Voltage, Protective Conductor Sizing, and Main Earthing Terminals 5.4 Residual Current Devices (RCD/RCCB), Earth Fault Protection, and Equipotential Bonding

6 Chapter 6: Installation Design, Single-Line Diagrams (SLD), and Cable Sizing

6.1 Single-Line Diagram (SLD) Preparation, Symbols, and Standard Layouts 6.2 Maximum Demand Calculation and Diversity Factors for ≤45 kVA 6.3 Cable Selection, Current-Carrying Capacity, and Correction Factors 6.4 Voltage Drop Calculations and Circuit Segregation Rules

7 Chapter 7: Testing and Commissioning

7.1 Inspection and Testing Sequence Overview and Visual Inspection 7.2 Continuity Testing of Protective and Equipotential Conductors 7.3 Insulation Resistance Testing and Polarity Verification 7.4 Earth Fault Loop Impedance (Zs), RCD Testing, and Post-Turn-On Checks

8 Chapter 8: Temporary Electrical Installations (SS 650)

8.1 SS 650 Part 1: Construction Site Temporary Electrical Supply 8.2 SS 650 Part 2: Festive Lighting, Trade Fairs, and Exhibition Supplies 8.3 Temporary Generators, Statement of Approval (SOA), and Safety Inspections

3.6 Motor Troubleshooting, Sequential Starting, and Programmable Logic Controllers (PLC)

Key Takeaways Explain This Topic AI

A motor that hums but cannot start is the classic signature of single-phasing: verify all three line voltages, fuses, and contactor poles before the locked-rotor current burns the winding.

Troubleshooting always begins with safe isolation and lock-out/tag-out, then supply verification, then control-circuit checks, and only then motor-side measurements.

Sequential starting staggers multiple motors with timers or PLC logic to avoid simultaneous DOL inrush, protecting the intake from voltage sag.

Soft starters ramp voltage to limit starting current to roughly 2–4 × FLC with adjustable torque, sitting between DOL and star-delta in cost and performance.

Emergency stops and safety interlocks must remain hard-wired (NC direct-opening contacts); a PLC must never be the sole device that disconnects power in an emergency.

Last updated: August 2026

3.6 Motor Troubleshooting, Sequential Starting, and Programmable Logic Controllers (PLC)

Quick Summary: The written syllabus and the practical test both demand structured motor fault-finding: isolate and lock out first, verify the supply, then diagnose from symptoms. The classic signatures are no-start , abnormal humming (single-phasing), stalling under load , overheating , and reverse rotation . Modern panels coordinate motors with sequential starting , soft starters , and PLCs — but emergency stops remain hard-wired.

1. Safe Diagnostic Sequence

Isolate and Lock-Out/Tag-Out (LOTO): open the isolator, apply a personal padlock and warning tag, and prove dead with a tested voltage indicator before touching terminals (Chapter 6.1 SLD duties and Chapter 8 LOTO practice).

Verify the supply: measure all three line-to-line voltages (≈ 400 V) and line-to-neutral (≈ 230 V) at the starter input; check the main MCB/MCCB and HRC fuses.

Check the control circuit: control fuse, stop and start pushbuttons, thermal overload relay (95–96) status, and contactor coil voltage (A1–A2).

Measure the motor: insulation resistance to earth (≥ 1 MΩ at 500 V DC) and winding continuity/balance across U–V, V–W, W–U.

2. Symptom Diagnosis Matrix

Symptom Most Probable Causes First Checks

Motor will not start (dead, silent) No supply; tripped TOR; blown control fuse; open contactor coil; faulty start button Line voltages; TOR reset; control-circuit continuity

Abnormal humming, fails to start Single-phasing (one line lost); severe mechanical jam; star-delta changeover failure All three fuses and contactor poles; voltage balance; rotor free to turn

Stalls or trips under load Overload beyond rating; low supply voltage; wrong TOR setting (0.58 rule ignored); bearing seizure Running current vs FLC; terminal voltage; TOR dial

Overheating in service Chronic overload; phase unbalance; blocked ventilation; excessive starts per hour Current balance; ambient/ventilation; duty cycle

Runs in reverse Two phases transposed anywhere upstream Phase-rotation meter; swap any two line conductors at the motor terminals

Single-Phasing Deep Dive

If one line fuse blows or one contactor pole welds open, a running 3-phase motor continues on two phases: the healthy windings carry current well above FLC, torque collapses, and the motor hums and overheats. Modern thermal overload relays include differential (phase-loss) tripping (Chapter 3.2); without it, the winding burns within minutes. A humming motor must be stopped immediately — the locked-rotor current is 6 × FLC or more.

3. Sequential Starting of Multiple Motors

Starting several DOL motors simultaneously multiplies inrush and collapses busbar voltage. Sequential starting staggers motors using timer relays or PLC logic:

Start the largest or process-critical motor first, then subsequent motors at 3–10 second intervals as each reaches speed.

In conveyor trains, the sequence is often downstream-first : the discharge conveyor starts before the feed conveyor so material never piles onto a stopped belt.

Interlocks enforce the order: the start circuit of motor 2 passes through a running-contact of motor 1 or a timer contact.

4. Soft Starters and Reduced-Voltage Alternatives

Soft starter: thyristor (SCR) voltage ramping limits starting current to roughly 2–4 × FLC with adjustable ramp time (2–30 s) and torque — smoother than star-delta, with no open transition; a bypass contactor carries the run current after ramp-up.

Comparison: DOL (6–8 × FLC, cheapest, typically ≤ 3.7 kW), star-delta (⅓ current and torque, light loads), soft starter (2–4 × FLC, adjustable), VFD (full speed control plus soft start, highest cost).

DC machines and welding sets: DC motors and DC welders deliver smooth torque and stable arcs; the syllabus expects awareness that DC welding sets are preferred over AC sets for general site welding because the rectified DC arc is more stable and easier to strike.

5. Programmable Logic Controllers (PLC), Relays, and Contactors

A PLC replaces hard-wired relay logic with a programmable unit: input devices (pushbuttons, limit switches, TOR contacts) are wired to input terminals; the stored program (traditionally ladder logic , mirroring the hard-wired diagrams of Chapter 3.2) evaluates rungs each scan cycle and drives outputs wired to relays and contactors that switch the motor power circuit.

Advantages: logic changes by reprogramming rather than rewiring; built-in timers and counters for sequential starting; diagnostics and status indication; easy addition of interlocks.

Limits: a crashed program or welded output relay must never defeat safety.

The hard rule: emergency stops, safety gates, and overload trips are hard-wired in series with the contactor coil (NC, direct-opening action). A PLC may add stop logic but must never be the sole means of removing power in an emergency.