Study guide

12.3 Distance, Angle & Tangent Mates

Certified SOLIDWORKS Associate CSWA

Track your progress as you read

Finished sections get a check mark.

1 Exam Overview & Logistics

1.1 Current Exam Facts & Format 1.2 Scoring, Points, Passing Score & Retakes 1.3 Time Management & Modeling Question Strategy

2 Workspace, Units & Design Intent

2.1 Interface & FeatureManager Tree 2.2 Document Units & MMGS Discipline 2.3 Design Intent Principles for CSWA

3 Sketch Foundations

3.1 Sketch Entities 3.2 Geometric Sketch Relations 3.3 Dimensions & Fully Defined Sketches

4 Sketch Construction Tools

4.1 Convert Entities, Offset & Mirror 4.2 Trim, Extend & Sketch Fillet/Chamfer 4.3 Construction Geometry & Sketch Planes

5 Extrude Boss & Cut

5.1 Extrude Boss/Base End Conditions 5.2 Extrude Cut Strategies 5.3 Contours, Thin Features & Common Extrude Traps

6 Revolves, Sweeps, Lofts & Edge Treatments

6.1 Revolve Boss & Revolve Cut 6.2 Sweep Boss/Base & Sweep Cut 6.3 Loft Boss/Base & Loft Cut 6.4 Fillet Features 6.5 Chamfer Features

7 Shell, Draft & Holes

7.1 Shell Feature 7.2 Draft Feature 7.3 Hole Wizard Fundamentals

8 Patterns & Mirror

8.1 Linear Pattern 8.2 Circular Pattern 8.3 Mirror Feature & Pattern Strategy 8.4 Fill Pattern & Choosing the Right Pattern Tool

9 Intermediate & Advanced Part Workflows

9.1 Multi-Feature Construction Order 9.2 Sketch Offset & Complex Profile Techniques 9.3 Editing, Rollback & Parent-Child

10 Materials & Mass Properties

10.1 Applying Materials & Density 10.2 Mass, Volume & Surface Area 10.3 Center of Mass, Coordinate Systems & Traps

11 Reference Geometry

11.1 Reference Planes 11.2 Axes, Points & Coordinate Systems 11.3 Mate References

12 Assembly Creation Basics

12.1 Inserting Components & Fixing the Base 12.2 Coincident, Concentric, Parallel, Perpendicular 12.3 Distance, Angle & Tangent Mates 12.4 Degrees of Freedom & Mate Diagnostics

13 Assembly Analysis & Advanced Mates

13.1 Advanced Mates Overview 13.2 Interference Detection 13.3 Assembly Mass Properties & Key Parameter Mods

14 Drafting Competencies

14.1 Standard & Projected Drawing Views 14.2 Section, Detail & Auxiliary Views 14.3 Dimensioning, BOM, Projection Standards & GD&T

12.3 Distance, Angle & Tangent Mates

Key Takeaways Explain This Topic AI

Distance mates set a numeric gap or offset between entities—prime targets when CSWA says “change the distance to X mm” and re-measure mass/CoM.

Angle mates lock a numeric angle between faces/edges/planes; use them for hinged orientations and modification steps that change an angle value.

Tangent mates create tangency between curved geometry (cylinders, spheres, cones) and faces or other curves—common for rollers, pins against flats, and spherical seats.

Prefer editing the existing Distance/Angle mate value for modifications rather than deleting and re-mating from scratch under time pressure.

Wrong Distance/Angle/Tangent direction or alignment still “solves” mathematically while producing wrong CoM—always verify with drag-test and the isometric.

Last updated: August 2026

12.3 Distance, Angle & Tangent Mates

Quick Answer: Use a Distance mate for a controlled gap/offset, an Angle mate for a controlled orientation in degrees, and a Tangent mate when a cylinder/sphere must touch a face or curve without sharing an axis. On modification questions, edit the mate dimension (for example 10 mm → 15 mm), rebuild, and re-run Mass Properties .

Coincident and Concentric place most parts. Distance , Angle , and Tangent handle clearances, angled poses, and curved contact—and they are especially important when CSWA assembly items ask you to change a key parameter and report a new mass or center of mass. These three mates are part of the official standard set alongside the four from 12.2.

Distance mate

Distance maintains a specified separation between selected entities (commonly face–face or plane–plane).

  • When the drawing wants Distance
  • A plate floats 5 mm above a base (not flush)
  • Two parallel faces must keep a slot width style offset realized by part faces
  • A stop face sits a documented air gap from another face
  • The problem later says: “Change the distance mate from 8 mm to 12 mm”
  • Distance workflow

Mate → select two faces (or valid pair).

Choose Distance .

Type the value in document units (MMGS → millimeters).

Use direction/flip controls so the gap is on the correct side.

OK → drag-test (motion should respect the locked gap).

Distance vs Coincident

  • Need Mate
  • Flush contact, no gap Coincident
  • Explicit nonzero gap/offset Distance
  • Gap of zero but you only know Distance tool Distance 0 can work but Coincident is clearer
  • Modification pattern (high value on exam)

CSWA loves multi-step assemblies:

Build mates including Distance = d₁ .

Measure assembly mass / CoM → enter answer A.

Edit Distance to d₂ (double-click mate dimension or Edit Feature on the mate).

Rebuild → Mass Properties again → answer B.

Do not delete the mate and rebuild the whole stack if you only need a value change. Editing preserves the rest of the constraint network.

Distance traps

  • Trap Result Fix
  • Wrong side of face Component on interior/exterior incorrectly Flip distance direction
  • Units wrong (inches typed as mm) Huge or tiny gap; mass/CoM nonsense Confirm MMGS; retype value
  • Distance between wrong faces Gap measures from fillets or sides Reselect primary planar faces from drawing
  • Competing coincident on same faces Over-defined mate error Remove conflict; one relationship wins
  • Angle mate

Angle locks the angle between two entities (faces, edges, planes) to a typed degree value.

  • Exam uses
  • Bracket folded at 30° to the base
  • Lever arm orientation 45° from a reference face

Modification: change angle 20° → 35° and re-measure CoM (angles move mass in space without changing part volumes— mass may stay the same while CoM coordinates change)

Angle workflow

Select two faces/edges that define the angle on the drawing.

Mate type Angle → enter degrees.

Flip/alignment options orient which quadrant the angle opens into— critical .

Preview against the isometric; OK; drag-test.

Angle vs Perpendicular vs Parallel

  • Relationship Mate
  • Exactly 90° Perpendicular or Angle 90° (Perpendicular is cleaner)
  • Exactly 0° / same direction Parallel or Angle 0° (Parallel is cleaner)
  • Any other numeric angle (15°, 30°, 120°…) Angle with that value
  • Mass vs CoM after angle edits

Changing only an Angle mate reorients parts. Total mass is usually unchanged (same parts, same materials). Center of mass coordinates almost always change . If the exam asks for mass after an angle-only edit and your mass moved, you accidentally edited geometry or material—not only the angle. If it asks for CoM and yours did not move, the angle mate may not have been the driving orientation (another mate still locked pose).

Tangent mate

Tangent forces tangency between selected geometry—classically a cylinder or sphere against a planar face , or curve-to-curve tangency where supported.

  • Exam uses
  • Roller or pin resting against a flat pad (not concentric to a hole)
  • Sphere sitting on a plane
  • Cylindrical cam/follower style contact simplified for associate-level geometry
  • Situations where Coincident face–face is impossible because one “face” is curved
  • Tangent vs Concentric
  • Goal Mate
  • Share the same axis (shaft in hole) Concentric
  • Touch along a generator/point without requiring shared axis Tangent

Putting Concentric on a cylinder and a plane fails; putting Tangent on two hole axes is the wrong mental model—use the mate that matches contact type.

Tangent workflow tips

Select cylindrical face + planar face (common case).

Mate → Tangent .

Flip if the cylinder goes to the wrong side of the plane.

Combine with other mates (coincident on end faces, parallel on a flat) to remove remaining DOF.

  • Combining mates: realistic stacks
  • Example A — Offset cover

Concentric: cover bosses ↔ base holes (or multiple concentric as needed).

Distance : underside of cover ↔ base top = 2 mm standoff.

Parallel or a third constraint if rotation about vertical remains and must be fixed.

Example B — Angled bracket

Coincident: bracket back ↔ vertical wall (or edge hinge setup per drawing).

Angle : bracket face ↔ base top = 60°.

Optional coincident of a side face to a mid plane for left/right position.

Example C — Cylinder against stop

Concentric: rod in sleeve (slides).

Tangent or Distance: rod end condition against a face per drawing.

Drag along axis if still free—add mate if design should be fixed for mass answer.

Modification questions: edit, don’t rebuild

Modification text (typical) What to edit What usually changes

Change distance from A to B mm Distance mate value Mass if gap changes interference/open air only slightly; CoM often; mass stable if only empty gap grows and no part geometry changes

  • Change angle from α to β Angle mate value CoM; mass usually same
  • Change a part dimension (hole Ø, extrude) Edit part / open part Mass and CoM
  • Replace material Material on component Mass and CoM

Read the stem: mate parameter vs part feature parameter . They are different edit paths. Mate edits stay in the assembly FeatureManager under Mates . Part edits require editing the component.

Note on mass with Distance: If Distance only separates rigid bodies further in empty space without changing part solids, total mass is unchanged ; CoM can still shift. If the exam reports mass changing after a “distance” step, look for a part dimension change, configuration, or suppressed body—not only a pure gap mate.

Alignment and preview discipline

Numeric mates are easy to accept with a wrong flip:

Distance 10 mm the wrong direction can push a part into the base (interference) or away opposite the isometric.

Angle 30° the wrong way mirrors the mechanism.

Tangent the wrong side parks the cylinder through the solid.

Always:

Watch preview before OK.

Compare to exam isometric .

Run Interference Detection if something looks buried (Chapter 13 deepens this).

Drag-test remaining freedom.

Exam time box for numeric mates

Within a ~18–20 minute assembly budget:

  • Phase Focus
  • Early Concentric/Coincident structure
  • Mid Distance/Angle/Tangent per drawing callouts
  • Late Edit modification values; Mass/CoM; enter answers

If a Distance mate fights an existing Coincident on related faces, stop stacking— diagnose conflict (12.4) rather than adding a fifth mate “to push harder.”

Practice drills that transfer to CSWA

Shaft-in-plate with shoulder coincident; add a Distance standoff version; edit 5→10 mm; record CoM each time.

Hinge-like bracket with Angle 0°, 45°, 90°; confirm mass constant and CoM moving.

Cylinder Tangent to a plane plus end coincident; flip tangent side once on purpose and see the failure mode.

Distance, Angle, and Tangent turn assemblies from “touching parts” into parameterized mechanisms the exam can score twice—once at the initial pose and once after a key edit. Pair them with DOF awareness (12.4) so underdefined free motion does not silently corrupt your second measurement.