Study guide

12.2 Coincident, Concentric, Parallel, Perpendicular

Certified SOLIDWORKS Associate CSWA

Track your progress as you read

Finished sections get a check mark.

1 Exam Overview & Logistics

1.1 Current Exam Facts & Format 1.2 Scoring, Points, Passing Score & Retakes 1.3 Time Management & Modeling Question Strategy

2 Workspace, Units & Design Intent

2.1 Interface & FeatureManager Tree 2.2 Document Units & MMGS Discipline 2.3 Design Intent Principles for CSWA

3 Sketch Foundations

3.1 Sketch Entities 3.2 Geometric Sketch Relations 3.3 Dimensions & Fully Defined Sketches

4 Sketch Construction Tools

4.1 Convert Entities, Offset & Mirror 4.2 Trim, Extend & Sketch Fillet/Chamfer 4.3 Construction Geometry & Sketch Planes

5 Extrude Boss & Cut

5.1 Extrude Boss/Base End Conditions 5.2 Extrude Cut Strategies 5.3 Contours, Thin Features & Common Extrude Traps

6 Revolves, Sweeps, Lofts & Edge Treatments

6.1 Revolve Boss & Revolve Cut 6.2 Sweep Boss/Base & Sweep Cut 6.3 Loft Boss/Base & Loft Cut 6.4 Fillet Features 6.5 Chamfer Features

7 Shell, Draft & Holes

7.1 Shell Feature 7.2 Draft Feature 7.3 Hole Wizard Fundamentals

8 Patterns & Mirror

8.1 Linear Pattern 8.2 Circular Pattern 8.3 Mirror Feature & Pattern Strategy 8.4 Fill Pattern & Choosing the Right Pattern Tool

9 Intermediate & Advanced Part Workflows

9.1 Multi-Feature Construction Order 9.2 Sketch Offset & Complex Profile Techniques 9.3 Editing, Rollback & Parent-Child

10 Materials & Mass Properties

10.1 Applying Materials & Density 10.2 Mass, Volume & Surface Area 10.3 Center of Mass, Coordinate Systems & Traps

11 Reference Geometry

11.1 Reference Planes 11.2 Axes, Points & Coordinate Systems 11.3 Mate References

12 Assembly Creation Basics

12.1 Inserting Components & Fixing the Base 12.2 Coincident, Concentric, Parallel, Perpendicular 12.3 Distance, Angle & Tangent Mates 12.4 Degrees of Freedom & Mate Diagnostics

13 Assembly Analysis & Advanced Mates

13.1 Advanced Mates Overview 13.2 Interference Detection 13.3 Assembly Mass Properties & Key Parameter Mods

14 Drafting Competencies

14.1 Standard & Projected Drawing Views 14.2 Section, Detail & Auxiliary Views 14.3 Dimensioning, BOM, Projection Standards & GD&T

12.2 Coincident, Concentric, Parallel, Perpendicular

Key Takeaways Explain This Topic AI

Standard CSWA mates you must command include Coincident, Concentric, Parallel, Perpendicular, Tangent, Distance, and Angle—plus Aligned vs Anti-Aligned flip control.

Mate workflow: select valid geometry (faces, edges, vertices, axes, planes) → choose mate type → set alignment → confirm preview → OK; then drag-test remaining freedom.

Coincident stacks faces/planes/points together; Concentric aligns cylindrical/conical axes—together they solve most shaft-in-hole patterns.

Parallel keeps directions the same without forcing contact distance; Perpendicular forces 90° between selected entities—use when drawings show square relationships without a contact face pair.

Mate errors usually mean wrong entity type, conflicting mates, or bad alignment—flip Aligned/Anti-Aligned before deleting the whole stack.

Last updated: August 2026

12.2 Coincident, Concentric, Parallel, Perpendicular

Quick Answer: Open Mate , select two valid entities (faces, edges, axes, planes…), choose a standard mate type, set Aligned or Anti-Aligned , and accept. Coincident + Concentric place most shafts and covers; Parallel and Perpendicular lock directions when contact alone is not enough. Always drag-test after a mate group.

SOLIDWORKS’s standard mate set used on CSWA includes Coincident, Concentric, Parallel, Perpendicular, Tangent, Distance, and Angle , with Aligned / Anti-Aligned control on many types. This section drills the four directional/position mates you apply constantly; Distance, Angle, and Tangent follow in 12.3, and DOF diagnostics in 12.4.

Mate PropertyManager workflow (memorize)

Insert → Mate (or Mate toolbar / context Mate).

Select geometry on component A, then component B (order rarely matters; entity type does).

SOLIDWORKS proposes a mate type— verify it matches intent; change type if the auto-guess is wrong.

Set alignment : Aligned vs Anti-Aligned (flip) until the preview matches the isometric/drawing.

Click ✓ / Add/OK to commit.

Drag the free component. Remaining motion should match the real mechanism (or no motion if fully constrained).

Valid selection cheat sheet

  • Mate type Typical selections
  • Coincident Face–face, plane–plane, point–point, edge–point, face–point (as allowed)
  • Concentric Cylindrical face–cylindrical face, axis–axis, cone–cone
  • Parallel Face–face, edge–edge, axis–axis, plane–plane
  • Perpendicular Face–face, edge–face, axis–plane, etc. (entities that define directions)

Trap: Selecting a fillet face when you meant the planar pad face , or selecting the hole edge circle when you needed the cylindrical hole face for concentric. Wrong topology → wrong or failed mate.

Coincident mate

Coincident forces selected entities to occupy the same place (faces share a plane of contact, points share a location, etc.).

  • Exam uses
  • Seat a cover flat on a base top face
  • Align a bracket face to a plate face
  • Put a vertex on a plane (less common but valid)
  • Mate a component plane to an assembly plane for orientation
  • Coincident vs Distance(0)

Coincident is the clean “touching / coplanar” mate. A Distance mate of 0 can look similar but is a different feature—prefer true Coincident when the drawing shows flush contact with no gap callout. Reserve Distance for nonzero clearances (12.3).

Alignment flip on faces

Face-to-face coincident can land outside (normals opposed wrong for your intent) or inside . Use Anti-Aligned / Aligned so the component sits on the correct side of the face. If the bracket appears buried in the plate, flip alignment before adding more mates.

Concentric mate

Concentric forces axes of cylindrical (or conical) geometry to coincide—the classic shaft through hole mate.

Exam pattern: shaft + hole + face seat

Most CSWA shaft assemblies use a two-mate kit:

Concentric — cylindrical shaft face ↔ cylindrical hole face (or axes).

Coincident — shaft shoulder face ↔ housing face (or similar axial stop).

That pair removes the major freedoms that would leave the shaft spinning in space or sliding forever. A third mate (Plane parallel, Angle, or another coincident) may finish rotation if the design is not free to spin.

  • Stage Mate Freedom removed (conceptually)
  • 1 Concentric shaft–hole Radial translation (2) + some rotation coupling; axis locked together
  • 2 Coincident shoulder–face Axial slide along the hole
  • 3 Optional parallel/angle/keyway coincident Spin about the shaft axis if design requires fixed rotation

You do not need to memorize exact DOF arithmetic for every combo under fire, but you do need to drag-test : after concentric+coincident, the shaft might still rotate—that can be correct for a pin. If the drawing shows a keyed fixed orientation, add the mate that stops rotation.

Concentric selection tips

Prefer cylindrical faces (easy to see).

Temporary axes work if faces are hard to pick (Right-click → Select Mid / show temporary axes).

Concentric on wrong diameter features (outer boss vs inner hole) still “succeeds” geometrically but places the part incorrectly—watch the preview.

Parallel mate

Parallel keeps two entities’ directions the same without forcing them to touch. Faces stay parallel; a gap may remain.

  • Exam uses
  • Keep a slot’s sides parallel to a base edge while another mate sets position

Orient a bracket so its face stays parallel to a plate when coincident on another face already sets contact elsewhere

Prevent unwanted tilt when only concentric is applied on a long part

Parallel is not Coincident. Parallel alone does not pull faces together. If the drawing shows flush contact, you need Coincident (or Distance 0 carefully), not only Parallel.

Perpendicular mate

Perpendicular forces a 90° relationship between selected entities (for example, two planar faces, or an edge and a face).

  • Exam uses
  • Square a plate edge to a base face when geometry is not already orthogonal from other mates
  • Enforce “upright” orientation after concentric leaves a spin DOF
  • Match drawing callouts that show perpendicularity without a third solid face to coincide to

Like Parallel, Perpendicular primarily fixes orientation , not a contact distance. Combine with Coincident/Concentric for full placement.

Aligned vs Anti-Aligned (flip)

Many mates expose alignment :

  • Control Typical effect
  • Aligned Selected directions/normals oriented the “same” way per SOLIDWORKS rules
  • Anti-Aligned Flipped relationship—component often pops to the other side or opposite sense

Exam habit: If the isometric shows the arm on the left and your mate puts it on the right, flip alignment before inventing new mates. Adding a conflicting coincident to “push” it over often creates mate errors or over-definition.

Standard mate error recovery

Symptom Likely cause Action

Mate dialog error / red mate Incompatible entity types or conflict with existing mates Undo last mate; check selections; flip alignment

  • Component jumps far away Anti-aligned vs aligned wrong; wrong faces Flip; reselect correct faces
  • “Over defined” Extra mate fights existing constraints Suppress last mate; use Mate Diagnostics (12.4)

Mate OK but wrong pose Valid but incorrect geometry chosen Delete mate; select the face the drawing actually contacts

Concentric fails Selected planar face or edge only Select cylindrical faces or axes

Do not panic-delete the base Fix. Fix is your ground. Delete recent mates in reverse order while watching the tree.

Worked mini-scenario

Assembly: Base (fixed), vertical plate with Ø10 hole, pin Ø10 with shoulder.

Concentric: pin cylinder ↔ hole cylinder. Preview: pin axis through hole; still slides and spins.

Coincident: pin shoulder face ↔ plate front face. Preview: seated depth; may still spin.

If the head has a flat that must stay horizontal: Parallel or Coincident between flat and Top plane / base top—choose what matches the drawing.

Drag pin: no translation; rotation only if intended.

Mass Properties when all parts constrained per stem.

Strategy under the 30-point clock

Mate major location pairs first (concentric+coincident kits).

Use Parallel/Perpendicular to kill wrong tilt before stacking Distance/Angle modifications.

After every 1–2 mates, drag-test once—cheaper than diagnosing ten mates at the end.

Keep the Mate popup open and add multiple mates in one session when efficient, but still verify each preview.

Master these four mates and the Aligned/Anti-Aligned flip, and most CSWA assembly geometry becomes a repeatable pattern rather than trial-and-error. Distance, Angle, and Tangent (12.3) then handle clearances, orientations with numeric values, and curved contact.