Study guide
Emergency Action Plans & Fire Prevention
BCSP Safety Trained Supervisor Construction STSC
Track your progress as you read
Finished sections get a check mark.
1 STSC Overview & OSHA 1926 Framework
The STSC Credential, Eligibility, and Exam Format How 29 CFR 1926 Is Organized Supervisor Roles and Responsibilities Under 1926
2 Safety Program Implementation
Safety Management Systems and Construction Safety Programs Training, Orientation, and Toolbox Talks Recordkeeping: OSHA 300 Forms and Safety Metrics Inspections, Audits, and Corrective Action
3 Hazard Identification & Control
Job Hazard Analysis and Risk Assessment The Hierarchy of Controls PPE Selection and Use Hazard Communication and GHS
4 The Fatal Four Construction Hazards
Fall Protection Systems Excavation and Trenching Safety Electrical Safety and Lockout/Tagout Struck-By and Caught-In/Between Hazards
5 Health Hazards & Industrial Hygiene
Chemical and Airborne Exposures: PELs, Lead, and Asbestos Silica, Noise, and Respiratory Protection Ergonomics and Heat/Cold Stress
6 Emergency Preparedness & Leadership
Emergency Action Plans & Fire Prevention Confined Space Entry in Construction Incident Investigation & Root Cause Analysis Safety Leadership & Ethics
Emergency Action Plans & Fire Prevention
Key Takeaways Explain This Topic AI
Where an OSHA standard requires an Emergency Action Plan (EAP), 29 CFR 1926.35 sets what it covers: reporting fires, evacuation routes and procedures, accounting for employees, and rescue/medical duties. It is written, or oral for 10 or fewer employees.
A portable fire extinguisher rated not less than 2A must be provided for each 3,000 square feet of protected building area, and travel distance to the nearest unit must not exceed 100 feet (1926.150).
A 10B-rated extinguisher must be within 50 feet of any location where more than 5 gallons of flammable/combustible liquid or 5 pounds of flammable gas are used (1926.150).
Fire Prevention Plans control ignition sources before a fire starts; EAPs control what people do once one starts - know which is proactive versus reactive.
1926.35(c) calls for an employee alarm system with a distinctive signal for each purpose, and 1926.150(e)(1) requires an alarm that can alert employees on site and the local fire department.
Last updated: November 2026
Why Emergency Preparedness Matters on the STSC
Emergency Preparedness and Management is Domain 4 of the STSC7 blueprint, at 16.6% of the exam, and fire prevention and protection lead its knowledge statements; hot work and confined spaces appear in Domain 2. A construction supervisor is usually the on-site decision-maker when an alarm sounds. The governing rules sit in 29 CFR 1926 Subpart C (general safety provisions, including emergency action plans) and Subpart F (fire protection and prevention).
Memorize two umbrella ideas first. An Emergency Action Plan (EAP) is reactive - it tells people what to do once an emergency exists. A Fire Prevention Plan (FPP) is proactive - it removes or controls hazards so the fire never starts.
Emergency Action Plans (29 CFR 1926.35)
Where an OSHA standard requires an emergency action plan, 1926.35 sets what it covers. The plan must be in writing (an employer with 10 or fewer employees may communicate it orally). The plan covers the designated actions employers and employees must take to ensure employee safety from fire and other emergencies.
The required minimum elements are:
Emergency escape procedures and escape route assignments .
Procedures for employees who remain to operate critical operations before they evacuate.
Procedures to account for all employees after evacuation is complete.
Rescue and medical duties for those employees who perform them.
The preferred means of reporting fires and other emergencies .
Names or job titles of persons who can be contacted for further information about the plan.
The employer must also designate and train enough people to assist in a safe and orderly evacuation, and review the plan with each employee when the plan is developed, when responsibilities change, and when the plan itself changes.
Employee Alarm Systems (1926.35(c) and 1926.150(e))
An EAP is only as good as the signal that triggers it. 1926.150(e)(1) requires an alarm system, such as a telephone system or siren, that can alert employees on the site and the local fire department. Under 1926.35(c) , if the employee alarm also serves another purpose, such as alerting fire brigade members, a distinctive signal must be used for each purpose. OSHA removed § 1926.159 from Part 1926 in 1996, although 1926.35(c) still names it. The general-industry alarm rule, 1910.165 , adds details such as being perceived above ambient noise or light levels and testing non-supervised systems every two months.
Fire Prevention and Portable Extinguishers (1926.150)
A Fire Prevention Plan (the general-industry term, 1910.39) describes fuel sources, control of ignition sources , proper handling and storage of hazardous materials, and the fire-protection equipment needed for each major hazard. In construction, 1926.24 makes the employer responsible for a fire protection and prevention program at the job site, and 1926.150(c) covers portable firefighting equipment .
Here is the math:
- Requirement Threshold (29 CFR 1926.150)
- Extinguisher rating per area Not less than 2A per 3,000 sq ft of protected building area
- Maximum travel distance to extinguisher 100 feet from any point
- Flammable-liquid protection 10B extinguisher within 50 feet of >5 gal liquid or >5 lb flammable gas
- Substitute for a 2A extinguisher One 55-gallon drum of water with two fire pails
- Multi-floor buildings At least one 2A extinguisher per floor , adjacent to the stairway
Portable extinguishers must be inspected periodically and maintained in accordance with NFPA No. 10A-1970 (1926.150(c)(1)(viii)).
Worked Example: Sizing Extinguishers
A single-story warehouse shell measures 9,000 square feet. How many 2A extinguishers are required at minimum?
Step 1: Divide protected area by 3,000 sq ft -> 9,000 / 3,000 = 3 extinguishers .
Step 2: Verify travel distance. With three units you must still confirm no worker is more than 100 feet from one; if the layout is long and narrow you may need extras to satisfy the 100-foot rule even though three satisfy the area rule. The more restrictive requirement always controls .
Common Exam Traps
Confusing 2A with 10B. 2A is the area/ordinary-combustible rating; 10B is the flammable-liquid rating tied to the 50-foot rule.
Mixing up 100 feet and 50 feet. 100 feet is general travel distance; 50 feet applies to the 10B near flammable liquids/gas.
Calling an EAP proactive. It is reactive; the FPP is proactive.
Forgetting the written requirement. A required EAP must be written and kept at the workplace; only employers with 10 or fewer employees may communicate it orally.
Assuming one signal covers everything. If the alarm serves more than one purpose, each purpose needs a distinctive signal (1926.35(c)(2)).
Hot Work and Fire Watch
Many construction fires start during hot work - welding, cutting, grinding, and brazing that produce sparks, slag, or open flame. 1926.352 does not require a permit, but a site program may add a hot work permit that verifies the area is clear of combustibles, extinguishers are staged, and a fire watch is posted. Under 1926.352(e) , when normal precautions are not sufficient, additional personnel must guard against fire during the work and for a sufficient period of time after completion to ensure that no possibility of fire exists, and they must be instructed on the anticipated fire hazards and the firefighting equipment. The general-industry rule, 1910.252(a)(2)(iii)(B) , sets a fire watch of at least half an hour after welding or cutting.
Flammable and Combustible Liquid Storage
Fire prevention also means controlling fuel. Under 1926.152 , only approved containers and portable tanks may be used to store and handle flammable and combustible liquids. No more than 25 gallons of flammable/combustible liquids may be stored in a room outside of an approved storage cabinet, and an approved flammable storage cabinet may hold no more than 60 gallons of Category 1, 2, or 3 flammable liquids (or up to 120 gallons of Category 4 combustible liquids). These quantities pair with the 10B/50-foot extinguisher rule above.
Means of Egress and Exit Routes
An EAP only works if workers can actually get out. Construction sites must maintain unobstructed exit routes : exits and the paths to them must be kept free of obstructions , adequately lit , and clearly marked . Exit doors must not be locked or blocked from the inside while workers are present. As floors and walls are erected, the supervisor must continually re-verify that evacuation paths remain open and that newly created floor openings and leading edges along egress routes are guarded so the escape route does not itself become a fall hazard.