Study guide
Struck-By and Caught-In/Between Hazards
BCSP Safety Trained Supervisor Construction STSC
Track your progress as you read
Finished sections get a check mark.
1 STSC Overview & OSHA 1926 Framework
The STSC Credential, Eligibility, and Exam Format How 29 CFR 1926 Is Organized Supervisor Roles and Responsibilities Under 1926
2 Safety Program Implementation
Safety Management Systems and Construction Safety Programs Training, Orientation, and Toolbox Talks Recordkeeping: OSHA 300 Forms and Safety Metrics Inspections, Audits, and Corrective Action
3 Hazard Identification & Control
Job Hazard Analysis and Risk Assessment The Hierarchy of Controls PPE Selection and Use Hazard Communication and GHS
4 The Fatal Four Construction Hazards
Fall Protection Systems Excavation and Trenching Safety Electrical Safety and Lockout/Tagout Struck-By and Caught-In/Between Hazards
5 Health Hazards & Industrial Hygiene
Chemical and Airborne Exposures: PELs, Lead, and Asbestos Silica, Noise, and Respiratory Protection Ergonomics and Heat/Cold Stress
6 Emergency Preparedness & Leadership
Emergency Action Plans & Fire Prevention Confined Space Entry in Construction Incident Investigation & Root Cause Analysis Safety Leadership & Ethics
Struck-By and Caught-In/Between Hazards
Key Takeaways Explain This Topic AI
Struck-by means a moving, flying, falling, swinging, or rolling object hits a worker; caught-in/between means a worker is pinned, crushed, or buried. Both are Fatal Four hazards.
Vehicle and equipment struck-by hazards demand high-visibility apparel (ANSI/ISEA 107), spotters, internal traffic control plans, and, on vehicles with an obstructed rear view, a reverse alarm audible above the surrounding noise or an observer.
Falling-object protection includes toeboards, screens, debris nets, hard hats, and barricaded danger zones below overhead work.
Caught-in/between includes trench cave-ins, unguarded machinery, and being pinned between equipment and a fixed object — controlled by machine guarding and LOTO.
Steel erection (Subpart R) requires fall protection above 15 feet, and demolition (Subpart T) requires a written engineering survey before work begins.
Last updated: November 2026
Defining the Last Two of the Fatal Four
The Fatal Four are falls, struck-by , caught-in/between , and electrocutions, four hazard categories behind many construction deaths. This section covers the two that are easiest to confuse on the exam.
Struck-by: injury from forcible contact with a moving object — flying, falling, swinging, or rolling. Examples: a falling tool, a swinging crane load, a nail from a nail gun, a backing dump truck, a collapsing wall fragment.
Caught-in/between: injury when a worker is squeezed, caught, crushed, pinched, or compressed between two or more objects, or buried. Examples: trench cave-in, being pinned between a truck and a wall, an unguarded machine pulling in a hand.
Telling them apart
The rule of thumb: if the injury comes mainly from the impact of the object, it is struck-by . If the injury comes from being crushed or caught between objects (or buried), it is caught-in/between . A worker pinned between a backing forklift and a stack of pipe is caught-in/between , not struck-by, because the harm is the crushing — a classic trap.
Struck-By Categories and Controls
OSHA groups struck-by into four sub-types:
- Sub-type Example Primary control
- Flying Nail-gun discharge, grinding fragment Eye/face PPE, tool guards
- Falling Dropped tool, falling materials Toeboards, nets, hard hats, barricades
- Swinging Crane/excavator load, taut line snap Tag lines, exclusion zones, signal person
- Rolling Backing trucks, mobile equipment Spotters, backup alarms, hi-vis apparel
- Vehicle and traffic controls
Work zones with mobile equipment require:
High-visibility apparel meeting ANSI/ISEA 107 for anyone exposed to traffic or equipment.
A spotter and an internal traffic control plan (ITCP) to separate workers from equipment.
On vehicles with an obstructed rear view, a reverse signal alarm audible above the surrounding noise or an observer who signals that it is safe to back (1926.601(b)(4)).
Barricades and signage per the MUTCD for public road work.
High-visibility apparel is rated by class : Class 2 for moderate-traffic and roadway work, and Class 3 (more reflective material, full sleeves) for high-speed traffic or low-light conditions. A flagger directing traffic on a highway needs at least Class 2, and often Class 3 at night.
Falling-object protection
When workers are below overhead work, protect them with toeboards (minimum 3½ inches in vertical height, per 1926.502(j)), screens , debris nets , canopies , and hard hats (ANSI Z89.1). Barricade the danger zone beneath the work so no one stands under suspended or overhead loads. The danger zone should account for the load's swing radius and the path a dropped object could bounce or roll.
Caught-In/Between Categories and Controls
The major caught-in/between hazards a supervisor must control:
Trench/excavation cave-ins — controlled by sloping, shoring, or shielding (Subpart P).
Unguarded machinery — rotating parts, augers, gears, belts; controlled by machine guarding and lockout/tagout during servicing.
Pinning hazards — being caught between equipment and a fixed object, or between two pieces of equipment; controlled by spotters, blocking, and standing clear of pinch points.
Collapsing materials or structures — wall sections, masonry, formwork; controlled by bracing and shoring.
Nail guns and powder-actuated tools
Flying-object struck-by injuries often come from pneumatic nail guns and powder-actuated tools . Controls the supervisor must enforce:
Use sequential-trip triggers (not bump/contact triggers) for most framing to prevent unintended double-fires.
Require eye and face protection (ANSI Z87.1) for the operator and nearby workers.
Powder-actuated tool operators must be trained in the operation of the particular tool (1926.302(e)(1)).
Never point a tool at anyone; treat it as loaded.
Machine guarding for caught-in
Under Subpart I (1926.300) , exposed moving parts — belts, gears, chains, rotating shafts, points of operation — must be guarded . A worker whose sleeve is pulled into an unguarded auger suffers a caught-in injury. Guards must be secured, not easily removed, and not create a new hazard. During servicing, guarding is replaced by lockout/tagout so the machine cannot start.
Cranes, Rigging, and Steel Erection
Many struck-by and caught-in events involve lifting:
Subpart CC (Cranes): keep loads at least 10 feet from power lines up to 50 kV; use a signal person when the operator's view is blocked; never stand under a suspended load.
Subpart R (Steel Erection): fall protection is required above 15 feet for most workers; connectors between 15 and 30 feet must be provided fall-protection equipment and training.
Subpart T (Demolition): a written engineering survey by a competent person must be completed before demolition begins to assess collapse potential.
Step-by-Step: Setting Up a Drop Zone
A supervisor controlling overhead-load risk should:
Identify the swing radius and load path.
Barricade the area below and downrange of the load.
Post a signal person and use tag lines to control the load.
Keep all non-essential workers out of the zone .
Require hard hats and verify rigging before each lift.
Common Mistakes
Calling a crushing/pinning injury "struck-by" — if the harm is being caught/crushed, it is caught-in/between .
Forgetting steel erection uses a 15-foot trigger, not 6 feet.
Allowing workers under suspended loads.
Skipping the demolition engineering survey .
Treating high-visibility apparel as optional around mobile equipment.