Study guide
How 29 CFR 1926 Is Organized
BCSP Safety Trained Supervisor Construction STSC
Track your progress as you read
Finished sections get a check mark.
1 STSC Overview & OSHA 1926 Framework
The STSC Credential, Eligibility, and Exam Format How 29 CFR 1926 Is Organized Supervisor Roles and Responsibilities Under 1926
2 Safety Program Implementation
Safety Management Systems and Construction Safety Programs Training, Orientation, and Toolbox Talks Recordkeeping: OSHA 300 Forms and Safety Metrics Inspections, Audits, and Corrective Action
3 Hazard Identification & Control
Job Hazard Analysis and Risk Assessment The Hierarchy of Controls PPE Selection and Use Hazard Communication and GHS
4 The Fatal Four Construction Hazards
Fall Protection Systems Excavation and Trenching Safety Electrical Safety and Lockout/Tagout Struck-By and Caught-In/Between Hazards
5 Health Hazards & Industrial Hygiene
Chemical and Airborne Exposures: PELs, Lead, and Asbestos Silica, Noise, and Respiratory Protection Ergonomics and Heat/Cold Stress
6 Emergency Preparedness & Leadership
Emergency Action Plans & Fire Prevention Confined Space Entry in Construction Incident Investigation & Root Cause Analysis Safety Leadership & Ethics
How 29 CFR 1926 Is Organized
Key Takeaways Explain This Topic AI
29 CFR 1926 is OSHA's construction standard, organized into lettered Subparts A through CC, each covering a hazard family.
Key subparts for construction supervisors include C (General Safety), K (Electrical), L (Scaffolds), M (Fall Protection), P (Excavations), and CC (Cranes).
Subpart C (1926.20–1926.35) establishes the employer's duty to run an accident-prevention program and to designate competent persons.
Construction triggers differ from general industry (1910): the construction fall-protection trigger is 6 feet, not the 1910 4-foot trigger.
Knowing which subpart governs a hazard lets you map any scenario question to the correct rule — falls to Subpart M, trenches to Subpart P, scaffolds to Subpart L.
Last updated: November 2026
What 29 CFR 1926 Is
29 CFR 1926 is Title 29 of the Code of Federal Regulations (CFR), Part 1926 — OSHA's Safety and Health Regulations for Construction . It is the core regulation for STSC study. Contrast it with 29 CFR 1910 , the general industry standard, which governs the STS but not the STSC.
A citation reads as a hierarchy. In 1926.501(b)(1) , the "1926" is the Part, "501" is the section, "(b)" is the subsection, and "(1)" is the paragraph. You don't need to memorize every paragraph number, but you must know which Subpart owns each hazard.
How the Subparts Are Lettered
Part 1926 is divided into lettered Subparts A through CC . Each subpart bundles a family of related sections. Learn these first:
- Subpart Topic Key sections
- C General Safety & Health Provisions 1926.20–1926.35
- D Occupational Health & Environmental Controls 1926.50–66 (silica is 1926.1153, in Subpart Z)
- E Personal Protective & Life-Saving Equipment 1926.95–107
- K Electrical 1926.400–449
- L Scaffolds 1926.450–454
- M Fall Protection 1926.500–503
- P Excavations 1926.650–652
- X Stairways and Ladders 1926.1050–1060
- CC Cranes and Derricks 1926.1400–1442
Memory hook: "L-M-P" = the elevated-and-earthwork core: scaffoLds, fall Movement (fall protection), excaPations. These three subparts plus electrical (K) cover most of the Fatal Four.
Subpart C: The Foundation
Subpart C (1926.20–1926.35) is the backbone every other subpart sits on. It establishes the employer's affirmative duties:
1926.20 — General safety and health provisions: the employer must initiate and maintain accident-prevention programs and provide for frequent and regular inspections by a competent person.
1926.21 — Safety training and education: employees must be instructed to recognize and avoid unsafe conditions .
1926.32 — Definitions, including the all-important "competent person" and "qualified person."
1926.35 — Employee emergency action plans.
Two definitions from 1926.32 matter most for supervisors:
Competent person — someone capable of identifying existing and predictable hazards AND who has authorization to take prompt corrective measures to eliminate them. Both halves are required; recognizing a hazard without authority does not make someone competent.
Qualified person — someone who, by degree, certificate, training, or extensive experience, has demonstrated the ability to solve problems relating to the subject matter.
Construction vs. General Industry Triggers
Do not swap a 1910 number for the 1926 number. Burn these construction-specific values into memory:
Fall protection trigger: 6 feet (1926.501) — general industry uses 4 feet.
Scaffold fall trigger: 10 feet (1926.451).
Excavation protective-system trigger: 5 feet (1926.652).
Guardrail top rail: 42 inches ± 3 inches (1926.502).
These live in different subparts but share a theme: construction tolerances reflect a higher-hazard environment.
Why Subpart Mapping Wins Points
When a scenario says "A worker is exposed to X — what does OSHA require?", mapping the hazard to its subpart narrows the answer before you read the options.
Worked Example
Scenario: A crew is working at the edge of a flat roof 12 feet above grade with no guardrail. Which standard governs, and what is required?
Identify the hazard: fall from an unprotected edge → Subpart M, Fall Protection .
Recall the trigger: 6 feet in construction → 12 feet clearly exceeds it.
Apply the requirement (1926.501): guardrails, safety nets, or a personal fall arrest system.
The distractor here is often a 10-foot answer (scaffold trigger) or a 4-foot answer (general industry). Because you mapped the hazard to Subpart M, you reject both.
Common Mistakes
Treating 1910 and 1926 numbers as interchangeable — they are not.
Forgetting that multiple subparts can apply to one task (a scaffold near energized lines invokes both L and K).
Assuming "competent person" just means "experienced." The authority to correct is the half people forget.
The Fatal Four and Their Subparts
A useful pattern in 1926 is the Fatal Four , which OSHA's training calls the Construction Focus Four: falls, struck-by, caught-in/between, and electrocution. BLS counted falls, slips, and trips as 39.2% of the 1,075 construction deaths in 2023, followed by transportation incidents at 22.3%. On the STSC7 blueprint they sit mainly in Domain 2, Hazard Identification and Control (28.5%). Map each to its subpart:
- Fatal Four hazard Primary subpart Example standard
- Falls (the #1 killer) M (and L for scaffolds) 1926.501
- Struck-by (vehicles, objects, equipment) CC (cranes), O (motor vehicles) 1926.1400 series, 1926.601
- Caught-in/between (trench collapse, machinery) P (excavations) 1926.652
- Electrocutions K (electrical) 1926.400 series
A reliable test move: when a question describes an injury, first decide which of the Fatal Four it is, then jump to that subpart.
How OSHA Enforces 1926
Understanding the enforcement backdrop helps you answer program and ethics questions. OSHA conducts inspections (programmed, complaint-driven, or post-incident) and issues citations classified by severity:
Other-than-serious — a condition unlikely to cause serious harm.
Serious — a substantial probability of death or serious physical harm that the employer knew or should have known about.
Willful — an intentional or knowing violation, carrying the highest maximum penalty, shared with repeat violations.
Repeat — a substantially similar violation found on re-inspection.
National Emphasis Programs (NEPs) concentrate inspection resources on specific hazards, such as falls, silica, and trenching. The supervisor's job is to keep the site continuously inspection-ready, not to scramble when OSHA arrives.
Learn the subpart map cold, and the rest of this guide — fall protection, excavation, electrical, industrial hygiene — becomes a set of details hung on a frame you already understand.