Study guide
RBX-4 — Raceway Fill, Conductor Fill, and Pulling Rules
Tennessee Limited Licensed Electrician LLE
Track your progress as you read
Finished sections get a check mark.
1 Electrical Theory and Calculations
GEK-1 — Electrical Quantities and Calculation Setup GEK-2 — DC Circuit Relationships GEK-3 — AC Systems and Power
2 NEC Navigation and Core Installation Rules
GEK-4 — NEC 2017 Structure, Definitions, and Lookup INS-1 — Approval, Listing, Labeling, and Instructions INS-2 — Working Space, Access, Guarding, and Enclosures
3 Safe Installations and Service Entrances
INS-3 — Workmanship, Protection, Identification, and OSHA Installation Safety SFB-1 — Load-Calculation Workflow SFB-2 — Service Conductors, Drops, Laterals, and Clearances
4 Service Equipment, Feeders, and Branch Circuits
SFB-3 — Service Equipment and Disconnecting Means SFB-4 — Feeder Sizing and Installation SFB-5 — Branch-Circuit Ratings, Conductors, and Loads
5 Dwelling Circuits, Personnel Protection, and Overcurrent Basics
SFB-6 — Dwelling-Unit Required Circuits and Outlet Placement SFB-7 — GFCI, AFCI, and Branch-Circuit Personnel Protection OCP-1 — Fuses, Circuit Breakers, Ratings, and Conductor Protection
6 Overcurrent Application and Bonding Foundations
OCP-2 — Overcurrent-Device Location and Application GND-1 — Grounding Versus Bonding and the Fault-Current Path GND-2 — Service Grounding and Bonding
7 Grounding Electrodes, Equipment Grounding, and Downstream Systems
GND-3 — Grounding Electrode Systems GND-4 — Equipment Grounding Conductors and Bonding Methods GND-5 — Feeders, Separate Buildings, Separately Derived Systems, and Special Bonding
8 Conductor Selection and Ampacity
CON-1 — Conductor Materials, Insulation, Markings, and Permitted Use CON-2 — Ampacity Tables and Terminal Temperature Limits CON-3 — Adjustment, Correction, and Special Ampacity Conditions
9 Cable Assemblies and Metal Raceway Systems
CON-4 — Cable Assemblies and Flexible Cords RBX-1 — Raceway Selection, Routing, Support, and Mechanical Protection RBX-2 — Metal Raceways
10 Nonmetallic Raceways, Fill, and Boxes
RBX-3 — Nonmetallic and Specialized Raceways RBX-4 — Raceway Fill, Conductor Fill, and Pulling Rules RBX-5 — Outlet, Device, Junction, and Pull Boxes
11 Hazardous Locations: Classification, Gases, Vapors, and Dusts
HAZ-1 — Classified-Location Framework HAZ-2 — Class I Flammable-Gas or Vapor Installations HAZ-3 — Class II Combustible-Dust Installations
12 Class III, Protection Techniques, and Signaling
HAZ-4 — Class III Fibers and Flyings HAZ-5 — Protection Techniques and Hazardous-Location Applications LVC-1 — Class 1/2/3, Alarm, and Signaling Circuits
13 Communications and Lighting Installations
LVC-2 — Communications Systems LGE-1 — Luminaires, Lampholders, and Lighting Outlets
14 Signs and General-Use Equipment
LGE-2 — Electric Signs and Outline Lighting LGE-3 — General-Use Equipment
RBX-4 — Raceway Fill, Conductor Fill, and Pulling Rules
Key Takeaways Explain This Topic AI
Chapter 9, Table 1 permits 53 percent fill for one conductor or cable, 31 percent for two, and 40 percent for more than two in a complete raceway system.
Table 4 supplies raceway areas and Table 5 or 5A supplies insulated-conductor areas; mixed sizes require summing actual listed areas rather than using a same-size Annex C shortcut.
A raceway nipple not over 24 in. between enclosures may use 60 percent fill, and its conductor-count adjustment exception is a separate condition that does not extend to the adjoining run.
Wire equipment-grounding conductors count for raceway fill, multiconductor cable counts as one cable by overall area, and fill compliance does not replace ampacity-adjustment or pulling checks.
Last updated: July 2026
Choose the percentage from Chapter 9, Table 1
Raceway fill limits protect conductor insulation and make installation practical. Chapter 9, Table 1 permits a maximum of 53 percent of the internal area for one conductor or cable, 31 percent for two, and 40 percent for more than two. These percentages apply to a complete conduit or tubing system. A short sleeve used only to protect exposed cable from damage is addressed by the notes rather than automatically treated as a complete raceway run.
The count is conductors and/or cables for geometric fill. A wire-type equipment grounding or bonding conductor is included, whether insulated or bare, using its applicable dimensions. This differs from ampacity adjustment: an EGC occupies space but normally carries no load and is not a current-carrying conductor. A grounded neutral can occupy fill space even when 310.15 permits excluding it from the current-carrying count.
A multiconductor cable, optical fiber cable, or flexible cord with two or more conductors is treated as one conductor for percentage selection and uses its actual overall cross-sectional area. If the cable is elliptical, calculate area as though its major diameter were the diameter of a circle. An assembly of individual insulated conductors without an overall covering is not one cable; count and total the individual conductors.
Use the correct area tables
Chapter 9, Table 4 lists internal raceway dimensions and the areas corresponding to the fill percentages for each raceway type and trade size. Schedule 40 PVC, Schedule 80 PVC, EMT, ENT, and other methods have different internal areas even at the same nominal size. Table 5 lists approximate dimensions and areas for insulated conductors such as THHN, and Table 5A addresses compact aluminum building wire. Table 8 supplies permitted bare-conductor dimensions.
Informative Annex C gives ready counts only when all conductors have the same size, insulation type, and raceway conditions matching the table. For mixed sizes, sum each conductor's area and compare the sum with the permitted Table 4 area. Do not average diameters, add AWG numbers, or use the largest conductor's Annex C count for a mixed group.
Example: a complete 3/4-in. EMT run contains six 10 AWG THHN conductors—including one wire EGC—and three 12 AWG THHN conductors. Because there are nine conductors, the 40 percent column applies. Table 5 gives 0.0211 in² for 10 AWG THHN and 0.0133 in² for 12 AWG THHN:
- six 10 AWG: 6 × 0.0211 = 0.1266 in²;
- three 12 AWG: 3 × 0.0133 = 0.0399 in²; and
total: 0.1266 + 0.0399 = 0.1665 in².
Table 4 gives 0.213 in² as the 40 percent area for 3/4-in. EMT. Since 0.1665 ≤ 0.213, the fill passes. The same group fails 1/2-in. EMT's 0.122 in² 40 percent area. Ampacity adjustment still uses the actual current-carrying count, not the fill count of nine.
Apply the nipple rule exactly
Chapter 9, Table 1 Note 4 permits a conduit or tubing nipple not over 24 in. long between boxes, cabinets, and similar enclosures to be filled to 60 percent of its total cross-sectional area. The allowance does not apply to a 25 in. nipple, a long run with a short crowded section, or an arbitrary protective sleeve.
Example: Table 4 gives 0.320 in² as the 60 percent area for a 3/4-in. EMT nipple. One 4 AWG THHN conductor occupies 0.0824 in². Three occupy 3 × 0.0824 = 0.2472 in², so they fit the nipple. The same three exceed the normal 40 percent area of 0.213 in² and would not fit a complete longer run of 3/4-in. EMT. Four occupy 0.3296 in² and exceed even the nipple's 0.320 in² allowance.
Note 4 also states that the more-than-three-current-carrying-conductor adjustment factors need not apply to this nipple condition. That is an ampacity exception tied to the qualifying nipple, not permission to ignore adjustment in the raceway on either side. Terminal temperature limits, equipment rules, and heat at the enclosures still apply.
Plan a pull that does not damage conductors
Raceway fill is a maximum, not a design target. Chapter 9 warns that three-conductor or cable pulls can jam when the raceway inside-diameter-to-cable outside-diameter ratio is between 2.8 and 3.2. Long pulls, many bends, large conductors, sidewall pressure, cold temperature, and difficult transitions can justify a larger raceway or lower fill.
Install the raceway complete between pull points before pulling conductors under 300.18. Ream cut ends and use insulating bushings where required, especially where 4 AWG or larger conductors enter an enclosure under 300.4(G). Use a pulling lubricant compatible with the insulation and raceway, observe manufacturer pulling-tension and minimum-bend-radius limits, and pull all conductors of the circuit as a coordinated group.
The applicable raceway article generally limits total bends to 360 degrees between pull points. Four 90-degree bends already reach that total; another offset requires a box or conduit body or a route change. A conduit body must remain accessible and be listed for the conductor size and use. If splices are made in it, its marked volume and 314.16(C) conditions apply. Pull and junction boxes for 4 AWG and larger conductors also need the directional dimensions calculated under 314.28, so passing conduit fill does not prove that the pull path is legal.