Study guide

6.3 GFCI and AFCI Requirements

Texas Journeyman Electrician License Exam Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the Texas Journeyman Electrician Exam 1.2 The Two-Part Exam Format (Knowledge + Calculations) 1.3 Eligibility, Application & Scheduling

2 NEC Structure & Navigation

2.1 Key NEC Definitions (Article 100) 2.2 How the NEC is Organized 2.3 NEC Index and Quick Lookup Strategies 2.4 Reading Electrical Plans, Symbols, and Schedules

3 Electrical Theory & Fundamentals

3.1 Ohm's Law, Power, and Series/Parallel Circuits 3.2 Conductors, Resistance, and Voltage Drop 3.3 Three-Phase Systems and Power Factor

4 Services & Service Equipment

4.1 Service Entrance Conductors and Service Point 4.2 Service Disconnecting Means 4.3 Grounding Electrode Systems for Services 4.4 Service Load Calculations

5 Separately Derived Systems & Feeders

5.1 Separately Derived Systems 5.2 Feeder Sizing, Ampacity, and Tap Rules 5.3 Feeder Load Calculations

6 Branch Circuits & Receptacles

6.1 Branch Circuit Sizing and Conductor Selection 6.2 Receptacle Spacing and Required Outlets 6.3 GFCI and AFCI Requirements 6.4 Lighting Outlets and Switch-Controlled Circuits

7 Overcurrent Protection

7.1 Overcurrent Principles and OCPD Types 7.2 Small-Conductor and Continuous-Load Rules 7.3 Motor Overcurrent and Short-Circuit Protection

8 Wiring Methods, Conductors & Boxes

8.1 Wiring Methods and Raceways 8.2 Conductor Insulations and Ampacity 8.3 Conduit and Raceway Fill 8.4 Boxes and Box Fill 8.5 Cable Trays and Underground Wiring 8.6 Cabinets, Cutout Boxes, and Panelboards

9 Equipment Grounding & Bonding

9.1 Equipment Grounding Conductors 9.2 Bonding & the Effective Ground-Fault Current Path 9.3 Equipment and Box Grounding Connections

10 Equipment, Devices & Transformers

10.1 Luminaires and Lighting (NEC Article 410) 10.2 Switches and Device Wiring (NEC Articles 404 & 400) 10.3 Appliances and Utilization Equipment (NEC Articles 422 & 424) 10.4 Transformers (NEC Article 450) 10.5 Working Space and Equipment Access (NEC 110.26)

11 Motors & Generators

11.1 Motor Branch Circuits & Conductors 11.2 Motor Disconnects, Controllers & Starters 11.3 Generators & Emergency Systems

12 Control Devices & Disconnecting Means

12.1 General Disconnecting Means Principles 12.2 HVAC and Refrigeration Disconnects 12.3 Motor Control Circuits and VFDs

13 Dwelling Load Calculations

13.1 General Lighting and Receptacle Load 13.2 Appliance, Range, and Dryer Load 13.3 Neutral Load and Service Sizing

14 Commercial & Advanced Calculations

14.1 Commercial Lighting and Receptacle Load 14.2 Continuous Loads and Equipment Demand 14.3 Voltage Drop and Conductor Sizing 14.4 Commercial Building Load Capstone

15 Special Occupancies & Conditions

15.1 Hazardous (Classified) Locations — NEC Articles 500–506 15.2 Health Care Facilities — NEC Article 517 15.3 Pools, Spas, and Fountains — NEC Article 680 (Beyond GFCI) 15.4 Other Specific Occupancies — A Survey 15.5 Data Processing Rooms and Communications Systems

16 Renewable Energy Technologies

16.1 Solar PV Systems (Article 690) 16.2 Energy Storage and EV Charging (Articles 706, 625)

17 Exam Strategy & Final Review

17.1 Time Management and NEC Lookup Speed 17.2 Test Day and Final Practice

6.3 GFCI and AFCI Requirements

Key Takeaways Explain This Topic AI

GFCI protection addresses shock from ground-fault current; AFCI protection addresses arcing faults that can start fires.

For dwellings, use 210.8(A) for receptacle locations, 210.8(D) for listed appliance categories and 210.8(F) for outdoor outlets.

The 2026 outdoor dwelling-outlet threshold in 210.8(F) is 60 A or less for the specified single-phase circuits; Texas retains the exception for listed outdoor HVAC equipment.

210.12(B) covers 120 V single-phase 10 A, 15 A and 20 A circuits in the listed dwelling areas; it does not simply say every circuit in every room.

GFCI does not replace required AFCI. A listed dual-function device can provide both when installed for the application.

Last updated: October 2026

Different Hazards Require Separate Checks

A Class A GFCI responds to a small imbalance between current leaving and returning through the circuit conductors. Its purpose is protection against electric shock. An AFCI recognizes hazardous arcing conditions associated with electrical fires. Passing one of these checks does not answer the other: some circuits need both kinds of protection.

For an exam question, identify the occupancy, location, circuit voltage and ampere rating, and the load served. Then look up the matching subsection. Avoid treating an appliance outlet, an outdoor outlet and a receptacle as interchangeable terms.

GFCI: Read the Location and Circuit Scope

  • Lookup Purpose
  • 210.8(A) Dwelling receptacles in the listed locations
  • 210.8(B) Receptacles in other-than-dwelling locations
  • 210.8(D) Outlets for specified appliances
  • 210.8(F) Outdoor dwelling outlets within the stated circuit limits

Dwelling locations include bathrooms, garages, outdoors, crawlspaces, basements, kitchens, laundry areas and the other locations specified in 210.8(A). The kitchen rule is not limited to countertop receptacles. Apply the section's voltage, circuit and location criteria, then read any applicable exception. The specific-appliance rule also covers certain hardwired outlets; installing equipment without a receptacle does not automatically remove GFCI protection.

2026 outdoor change: Section 210.8(F) increases the circuit threshold from 50 A to 60 A , for the covered single-phase outdoor outlets supplied at 150 V or less to ground. Texas’s adoption rule preserves the exception for outlets supplying listed outdoor HVAC equipment without the model-code expiration date. It does not exempt every outdoor load or every 60 A circuit.

AFCI: Listed Areas and Permitted Methods

210.12(B) applies to 120 V single-phase 10 A, 15 A and 20 A branch circuits supplying outlets or devices in the listed dwelling areas. These include kitchens, family and living rooms, dining rooms, bedrooms, closets, hallways, laundry areas and similar areas. Determine coverage from that list, not from a blanket statement that all dwelling circuits require AFCI.

210.12(A) describes permitted protection methods. A listed combination-type AFCI at the circuit origin is a common approach. Other methods have conditions involving the wiring method, upstream protection or a listed system combination; an arbitrary AFCI receptacle at the first outlet is not automatically sufficient.

Do not assume smoke alarms or fire-alarm equipment are universally exempt. An exception has its own installation conditions and must be read in full. Likewise, GFCI protection in a bathroom or garage is not itself an AFCI exemption; decide whether the circuit serves an AFCI-covered area.

Existing Circuits and Device Selection

For extensions, modifications and replacements, use 210.12(E) . The 2026 wording permits the specified outlet branch-circuit AFCI at the first receptacle outlet or switch of the existing circuit when that compliance option applies. Read the exception and the other conditions before applying it.

A dual-function AFCI/GFCI breaker can address both requirements when listed for the panel and installation. A combination-type AFCI alone is not the same thing as a dual-function AFCI/GFCI device. “Combination” in the AFCI name refers to arc-fault protection, not added shock protection.

Finally, follow device instructions for LINE/LOAD connections and testing. Do not cite 210.8(C) as a monthly-test rule; test-button maintenance instructions come from the device manufacturer. Correct listing, circuit coverage and wiring all matter.

References: TDLR’s September 2026 adoption , Eaton’s AFCI scope explanation , and 2026 changes to existing-circuit AFCI protection .