Study guide
3.1 Ohm's Law, Power, and Series/Parallel Circuits
Texas Journeyman Electrician License Exam Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the Texas Journeyman Electrician Exam 1.2 The Two-Part Exam Format (Knowledge + Calculations) 1.3 Eligibility, Application & Scheduling
2 NEC Structure & Navigation
2.1 Key NEC Definitions (Article 100) 2.2 How the NEC is Organized 2.3 NEC Index and Quick Lookup Strategies 2.4 Reading Electrical Plans, Symbols, and Schedules
3 Electrical Theory & Fundamentals
3.1 Ohm's Law, Power, and Series/Parallel Circuits 3.2 Conductors, Resistance, and Voltage Drop 3.3 Three-Phase Systems and Power Factor
4 Services & Service Equipment
4.1 Service Entrance Conductors and Service Point 4.2 Service Disconnecting Means 4.3 Grounding Electrode Systems for Services 4.4 Service Load Calculations
5 Separately Derived Systems & Feeders
5.1 Separately Derived Systems 5.2 Feeder Sizing, Ampacity, and Tap Rules 5.3 Feeder Load Calculations
6 Branch Circuits & Receptacles
6.1 Branch Circuit Sizing and Conductor Selection 6.2 Receptacle Spacing and Required Outlets 6.3 GFCI and AFCI Requirements 6.4 Lighting Outlets and Switch-Controlled Circuits
7 Overcurrent Protection
7.1 Overcurrent Principles and OCPD Types 7.2 Small-Conductor and Continuous-Load Rules 7.3 Motor Overcurrent and Short-Circuit Protection
8 Wiring Methods, Conductors & Boxes
8.1 Wiring Methods and Raceways 8.2 Conductor Insulations and Ampacity 8.3 Conduit and Raceway Fill 8.4 Boxes and Box Fill 8.5 Cable Trays and Underground Wiring 8.6 Cabinets, Cutout Boxes, and Panelboards
9 Equipment Grounding & Bonding
9.1 Equipment Grounding Conductors 9.2 Bonding & the Effective Ground-Fault Current Path 9.3 Equipment and Box Grounding Connections
10 Equipment, Devices & Transformers
10.1 Luminaires and Lighting (NEC Article 410) 10.2 Switches and Device Wiring (NEC Articles 404 & 400) 10.3 Appliances and Utilization Equipment (NEC Articles 422 & 424) 10.4 Transformers (NEC Article 450) 10.5 Working Space and Equipment Access (NEC 110.26)
11 Motors & Generators
11.1 Motor Branch Circuits & Conductors 11.2 Motor Disconnects, Controllers & Starters 11.3 Generators & Emergency Systems
12 Control Devices & Disconnecting Means
12.1 General Disconnecting Means Principles 12.2 HVAC and Refrigeration Disconnects 12.3 Motor Control Circuits and VFDs
13 Dwelling Load Calculations
13.1 General Lighting and Receptacle Load 13.2 Appliance, Range, and Dryer Load 13.3 Neutral Load and Service Sizing
14 Commercial & Advanced Calculations
14.1 Commercial Lighting and Receptacle Load 14.2 Continuous Loads and Equipment Demand 14.3 Voltage Drop and Conductor Sizing 14.4 Commercial Building Load Capstone
15 Special Occupancies & Conditions
15.1 Hazardous (Classified) Locations — NEC Articles 500–506 15.2 Health Care Facilities — NEC Article 517 15.3 Pools, Spas, and Fountains — NEC Article 680 (Beyond GFCI) 15.4 Other Specific Occupancies — A Survey 15.5 Data Processing Rooms and Communications Systems
16 Renewable Energy Technologies
16.1 Solar PV Systems (Article 690) 16.2 Energy Storage and EV Charging (Articles 706, 625)
17 Exam Strategy & Final Review
17.1 Time Management and NEC Lookup Speed 17.2 Test Day and Final Practice
3.1 Ohm's Law, Power, and Series/Parallel Circuits
Key Takeaways Explain This Topic AI
Ohm's Law states E = I × R; knowing any two of voltage, current, or resistance lets you solve for the third.
Watt's Law gives three forms for power: P = E × I, P = I² × R, and P = E² / R.
In a series circuit, current is the same everywhere, voltage divides across each load, and resistances add directly (R_T = R1 + R2 + R3).
In a parallel circuit, voltage is the same across every branch, currents add at each junction, and the equivalent resistance is the reciprocal of the sum of reciprocals (1/R_T = 1/R1 + 1/R2 + 1/R3).
Every load calculation, motor full-load current check, and voltage drop computation on the Calculations part of the exam traces back to these two laws.
Last updated: October 2026
Why This Matters for the Texas Journeyman Exam
The Calculations part of the TDLR/PSI journeyman exam (26 questions, 110 minutes) is built on two algebraic relationships: Ohm's Law and Watt's Law . Whether the question asks you to size a branch-circuit conductor, compute the voltage drop on a 250-foot feeder, or verify a motor's full-load current, every formula reduces to one of these two laws. The Knowledge part (59 questions, 130 min) also leans on series and parallel circuit behavior when it tests your understanding of equipment grounding paths, tap rules, and multi-wire branch circuits.
This section defines the variables, presents the formula set, and works through circuit examples you will see on exam day.
The Four Quantities
Every electrical calculation on the exam uses four variables:
- Symbol Quantity Unit Unit Abbreviation
- E Voltage (electromotive force) volts V
- I Current amperes A
- R Resistance ohms Ω
- P Power watts W
The NEC uses E for voltage in its informational notes and examples; some textbooks use V . The formulas are identical either way.
Ohm's Law (E = I × R)
Ohm's Law states that the voltage dropped across a resistance equals the current through it multiplied by the resistance. Rearranged, it gives three working forms:
- To find Formula
- Voltage E = I × R
- Current I = E ÷ R
- Resistance R = E ÷ I
- Worked Example 1 — Solving for Current
A 120-volt incandescent lighting circuit has a total resistance of 24 Ω. What current flows?
- I = E ÷ R = 120 ÷ 24 = 5 A
- Worked Example 2 — Solving for Resistance
A 277-volt lighting load draws 11 A. What is the equivalent resistance?
- R = E ÷ I = 277 ÷ 11 = 25.2 Ω
- Watt's Law (Power in a Circuit)
Watt's Law gives the real power dissipated by a resistive load. It has three forms, each useful depending on which two quantities you know:
- To find Formula Use when you know
- Power P = E × I Voltage and current
- Power P = I² × R Current and resistance
- Power P = E² ÷ R Voltage and resistance
- Worked Example 3 — Power from Voltage and Current
A 240-volt electric water heater draws 18.3 A. What is the power consumption?
- P = E × I = 240 × 18.3 = 4,392 W (≈ 4.4 kW)
- Worked Example 4 — Power from Current and Resistance
A heating element carries 12 A through 10 Ω. Power?
- P = I² × R = 12² × 10 = 144 × 10 = 1,440 W
- Worked Example 5 — Power from Voltage and Resistance
A 208-volt resistive load has 16.6 Ω resistance. Power?
- P = E² ÷ R = 208² ÷ 16.6 = 43,264 ÷ 16.6 = 2,604 W (≈ 2.6 kW)
- Series Circuits
In a series circuit , all current flows through a single path — every load is connected end-to-end. Three rules govern series circuits:
- Current is the same at every point: I_T = I1 = I2 = I3
- Voltage adds across the loads: E_T = E1 + E2 + E3
- Resistance adds directly: R_T = R1 + R2 + R3
- Worked Example 6 — Series Circuit
A 120-volt source supplies three resistors in series: 4 Ω, 6 Ω, and 10 Ω.
- Total resistance: R_T = 4 + 6 + 10 = 20 Ω
- Total current: I = 120 ÷ 20 = 6 A (same through every resistor)
- Voltage across each: E(4Ω) = 6 × 4 = 24 V; E(6Ω) = 6 × 6 = 36 V; E(10Ω) = 6 × 10 = 60 V
- Check: 24 + 36 + 60 = 120 V ✓
- Total power: P = 120 × 6 = 720 W
A series circuit is rare in power wiring (an open on one load kills the whole string), but the arithmetic appears in voltage-drop and tap-rule questions.
Parallel Circuits
In a parallel circuit , each load is connected across the same two supply conductors. This is how every branch circuit and feeder in a building is wired. Three rules govern parallel circuits:
- Voltage is the same across every branch: E_T = E1 = E2 = E3
- Current adds at each junction: I_T = I1 + I2 + I3
- Reciprocal resistance : 1/R_T = 1/R1 + 1/R2 + 1/R3
For two resistors only , the product-over-sum shortcut is faster:
- R_T = (R1 × R2) ÷ (R1 + R2)
- Worked Example 7 — Two-Resistor Parallel
A 120-volt circuit feeds two parallel loads: 10 Ω and 15 Ω.
- Branch currents: I(10Ω) = 120 ÷ 10 = 12 A; I(15Ω) = 120 ÷ 15 = 8 A
- Total current: I_T = 12 + 8 = 20 A
- Equivalent resistance (shortcut): R_T = (10 × 15) ÷ (10 + 15) = 150 ÷ 25 = 6 Ω
- Check: I = 120 ÷ 6 = 20 A ✓
- Total power: P = 120 × 20 = 2,400 W
- Worked Example 8 — Three or More Resistors in Parallel
Three 30 Ω resistors are paralleled across a 240-volt supply.
1/R_T = 1/30 + 1/30 + 1/30 = 3/30 = 1/10 → R_T = 10 Ω
I_T = 240 ÷ 10 = 24 A (8 A per branch). P = 240 × 24 = 5,760 W .
How These Laws Connect to the NEC
The exam will rarely ask a bare theory question. Instead it wraps Ohm's and Watt's Laws inside NEC scenarios:
Branch-circuit sizing (NEC 210.19, 210.20): Continuous load × 125% uses the current value you computed with I = P ÷ E.
Motor full-load current (NEC 430.22, Table 430.250): Conductor sized at 125% of FLC; the FLC itself comes from the NEC table, but verifying it against a nameplate uses I = P ÷ (E × 1.732 × PF × η) for three-phase motors.
Voltage drop (NEC 210.19(A) Informational Note No. 4, 215.2(A) Informational Note No. 2): VD = I × R, scaled by circuit length and the 1.732 or 2 factor — all built on Ohm's Law.
Service calculations (NEC Article 120): Demand factors reduce the connected load in watts; the resulting current determines conductor and overcurrent sizes via I = P ÷ E.
Key Formula Reference Table
- Law Formula Solves for
- Ohm's E = I × R Voltage
- Ohm's I = E ÷ R Current
- Ohm's R = E ÷ I Resistance
- Watt's P = E × I Power (V and I known)
- Watt's P = I² × R Power (I and R known)
- Watt's P = E² ÷ R Power (E and R known)
- Series R_T = R1 + R2 + R3 Total series resistance
- Parallel (two) R_T = (R1 × R2) ÷ (R1 + R2) Two-resistor equivalent
- Parallel (n) 1/R_T = 1/R1 + 1/R2 + … Many-resistor equivalent