Study guide

10.1 Luminaires and Lighting (NEC Article 410)

Texas Journeyman Electrician License Exam Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the Texas Journeyman Electrician Exam 1.2 The Two-Part Exam Format (Knowledge + Calculations) 1.3 Eligibility, Application & Scheduling

2 NEC Structure & Navigation

2.1 Key NEC Definitions (Article 100) 2.2 How the NEC is Organized 2.3 NEC Index and Quick Lookup Strategies 2.4 Reading Electrical Plans, Symbols, and Schedules

3 Electrical Theory & Fundamentals

3.1 Ohm's Law, Power, and Series/Parallel Circuits 3.2 Conductors, Resistance, and Voltage Drop 3.3 Three-Phase Systems and Power Factor

4 Services & Service Equipment

4.1 Service Entrance Conductors and Service Point 4.2 Service Disconnecting Means 4.3 Grounding Electrode Systems for Services 4.4 Service Load Calculations

5 Separately Derived Systems & Feeders

5.1 Separately Derived Systems 5.2 Feeder Sizing, Ampacity, and Tap Rules 5.3 Feeder Load Calculations

6 Branch Circuits & Receptacles

6.1 Branch Circuit Sizing and Conductor Selection 6.2 Receptacle Spacing and Required Outlets 6.3 GFCI and AFCI Requirements 6.4 Lighting Outlets and Switch-Controlled Circuits

7 Overcurrent Protection

7.1 Overcurrent Principles and OCPD Types 7.2 Small-Conductor and Continuous-Load Rules 7.3 Motor Overcurrent and Short-Circuit Protection

8 Wiring Methods, Conductors & Boxes

8.1 Wiring Methods and Raceways 8.2 Conductor Insulations and Ampacity 8.3 Conduit and Raceway Fill 8.4 Boxes and Box Fill 8.5 Cable Trays and Underground Wiring 8.6 Cabinets, Cutout Boxes, and Panelboards

9 Equipment Grounding & Bonding

9.1 Equipment Grounding Conductors 9.2 Bonding & the Effective Ground-Fault Current Path 9.3 Equipment and Box Grounding Connections

10 Equipment, Devices & Transformers

10.1 Luminaires and Lighting (NEC Article 410) 10.2 Switches and Device Wiring (NEC Articles 404 & 400) 10.3 Appliances and Utilization Equipment (NEC Articles 422 & 424) 10.4 Transformers (NEC Article 450) 10.5 Working Space and Equipment Access (NEC 110.26)

11 Motors & Generators

11.1 Motor Branch Circuits & Conductors 11.2 Motor Disconnects, Controllers & Starters 11.3 Generators & Emergency Systems

12 Control Devices & Disconnecting Means

12.1 General Disconnecting Means Principles 12.2 HVAC and Refrigeration Disconnects 12.3 Motor Control Circuits and VFDs

13 Dwelling Load Calculations

13.1 General Lighting and Receptacle Load 13.2 Appliance, Range, and Dryer Load 13.3 Neutral Load and Service Sizing

14 Commercial & Advanced Calculations

14.1 Commercial Lighting and Receptacle Load 14.2 Continuous Loads and Equipment Demand 14.3 Voltage Drop and Conductor Sizing 14.4 Commercial Building Load Capstone

15 Special Occupancies & Conditions

15.1 Hazardous (Classified) Locations — NEC Articles 500–506 15.2 Health Care Facilities — NEC Article 517 15.3 Pools, Spas, and Fountains — NEC Article 680 (Beyond GFCI) 15.4 Other Specific Occupancies — A Survey 15.5 Data Processing Rooms and Communications Systems

16 Renewable Energy Technologies

16.1 Solar PV Systems (Article 690) 16.2 Energy Storage and EV Charging (Articles 706, 625)

17 Exam Strategy & Final Review

17.1 Time Management and NEC Lookup Speed 17.2 Test Day and Final Practice

10.1 Luminaires and Lighting (NEC Article 410)

Key Takeaways Explain This Topic AI

NEC 410.6: all luminaires, lampholders, and retrofit kits must be listed for the location they serve

NEC 410.16(D) clothes-closet clearances: surface-mounted incandescent or LED (enclosed light source) = 12 in.; surface-mounted fluorescent = 6 in.; recessed incandescent/LED or fluorescent = 6 in. from the storage plane

NEC 410.10(D): luminaires in the bathtub/shower zone (3 ft horizontally and 8 ft vertically from the rim or threshold) must be listed for damp locations, or wet locations where subject to shower spray; cord-connected, pendant, chain/cable-suspended, and track luminaires are prohibited in the zone

NEC 410.36: a luminaire weighing 50 lb or less may be supported by the outlet box alone if the box is listed for the load

NEC 410.130(C): each commercial luminaire requires an individual disconnecting means that opens all ungrounded conductors

Last updated: August 2026

Why This Matters for the TX Journeyman Exam

Article 410 — Luminaires, Lampholders, and Lamps falls under content outline area 6 (Equipment & Devices). Most 410 questions appear in the NEC Knowledge part of the exam and test your recall of clearance distances, support rules, and the commercial luminaire disconnect requirement. A smaller number show up in Calculations when a branch circuit must be sized for a lighting load, but the calculation mechanics belong to Ch6.

Listing Required (NEC 410.6)

Every luminaire, lampholder, and retrofit kit must be listed (NEC 410.6). Field-fabricated luminaires are not permitted unless listed and labeled. The listing confirms suitability for the location — damp, wet, or hazardous — and validates the markings on the luminaire. A luminaire installed in a location for which it is not listed is a code violation even when it appears to function.

Damp and Wet Locations (NEC 410.10(A))

NEC 410.10(A) requires a luminaire installed in a damp or wet location to be identified for that location. A damp location is subject to moderate levels of moisture (covered porches, under canopies); a wet location is subject to saturation (direct rain, shower stalls, below grade). Luminaires marked "Suitable for Damp Locations" may not be installed in wet locations. Recessed luminaires in wet locations must use a gasket or seal listed for the application.

Luminaires Near Combustible Material (NEC 410.10)

NEC 410.10 requires luminaires to be constructed, installed, or equipped with shades or guards so combustible material is not subjected to temperatures above 90°C (194°F). Recessed luminaires must be spaced from insulation per their listing (Type IC vs non-IC). A luminaire mounted close to stored combustibles must be listed for that use.

Clothes Closets — Clearance Table (NEC 410.16(D))

NEC 410.16 governs luminaires in clothes closets. Section 410.16(A) defines the storage space (the space defined by the closet walls and the vertical planes at the shelf edge and closet rod). The clearance requirements appear in NEC 410.16(D) and are measured from the nearest point of the luminaire to the storage plane. Four luminaire types carry specific minimum clearances:

Luminaire Type Minimum Clearance from Storage Plane

Surface-mounted incandescent or LED (enclosed light source) 12 in.

Surface-mounted fluorescent 6 in.

Recessed incandescent or LED 6 in.

Recessed fluorescent 6 in.

Pendant luminaires and lampholders are not permitted in clothes closets. Closet rods must not extend past the luminaire's clearance zone.

Exception to 410.16(D): surface-mounted fluorescent or LED luminaires that are identified for clothes-closet use may be installed within the storage space, provided they are listed and installed per their marking.

Luminaires in Bathtub and Shower Areas (NEC 410.10(D))

NEC 410.10(D) governs luminaires near bathtubs and showers. Two subrules apply:

410.10(D)(1) — Restricted zone: a zone measuring 3 ft horizontally and 8 ft vertically from the top of the bathtub rim or shower threshold is established. Within this zone, cord-connected luminaires, pendants, chain- or cable-suspended luminaires, lighting track, and ceiling-suspended (paddle) fans with light kits are prohibited .

410.10(D)(2) — Location marking: luminaires located within the actual dimensions of the tub or shower up to 8 ft above the rim or threshold must be marked suitable for damp locations , or suitable for wet locations where subject to shower spray.

Article 410 does not impose a blanket GFCI-protection requirement on shower luminaires. GFCI protection for shower-area receptacles comes from NEC 210.8 (covered in Ch6), and any GFCI requirement on the luminaire itself would come from the manufacturer's instructions enforced via NEC 110.3(B), not from 410.10(D).

Luminaire Support (NEC 410.36)

A luminaire weighing 50 lb or less may be supported by the outlet box alone, provided the box is listed for the load. Heavier luminaires require independent support from the building structure or a listed fixture stud. Cord-and-plug-connected luminaires must be supported independently of the attachment plug.

Luminaire Whips and Taps (NEC 410.117(C), 410.48)

NEC 410.117(C) permits a 6 ft maximum flexible whip (flexible metal or nonmetallic conduit, or listed fixture wire in a suitable raceway or Type AC/MC cable) between a junction box and a recessed luminaire. The fixture wire must be at least 18 AWG on 15 A and 20 A branch circuits per NEC 240.5(B)(2).

NEC 410.48 allows a luminaire tap from a 20 A branch circuit: the tap conductor must run in a suitable raceway or Type AC/MC cable, be sized for the luminaire load, and terminate on the luminaire side of the ballast/driver. The tap length range is 18 in. minimum to 6 ft maximum — the 18 in. minimum prevents the tap from being too short to safely route, and the 6 ft maximum bounds the unprotected run.

Commercial Luminaire Disconnect (NEC 410.130(C))

In commercial installations, NEC 410.130(C) requires each luminaire to have an individual disconnecting means that simultaneously opens all ungrounded conductors supplying that luminaire. Acceptable means include:

  • A cord-and-plug connection to a receptacle supplied by the luminaire circuit
  • A listed luminaire disconnect installed on the luminaire side of the ballast/driver

A wall switch or circuit breaker if it is within sight of the luminaire (within 50 ft) and dedicated to that luminaire

A high-bay luminaire with a cord-and-plug connection satisfies the rule through its receptacle. The disconnect must be accessible to maintenance personnel and is not required to be at the luminaire itself. Industrial installations may use a single disconnect for a group of luminaires where documented maintenance procedures ensure the circuit is de-energized before any luminaire is serviced.

Residential installations have no equivalent individual-disconnect rule. The exam frequently tests whether a residential garage luminaire needs an individual disconnect — it does not.

Track Lighting (NEC 410.140–410.154)

Track lighting (NEC 410.140) must be listed and labeled, and each track section must be supported independently. The track load must not exceed the track's listed ampere rating. Track lighting in residential clothes closets, damp/wet locations, and concealed spaces is restricted per 410.152.