Study guide

1.1 About the Texas Journeyman Electrician Exam

Texas Journeyman Electrician License Exam Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the Texas Journeyman Electrician Exam 1.2 The Two-Part Exam Format (Knowledge + Calculations) 1.3 Eligibility, Application & Scheduling

2 NEC Structure & Navigation

2.1 Key NEC Definitions (Article 100) 2.2 How the NEC is Organized 2.3 NEC Index and Quick Lookup Strategies 2.4 Reading Electrical Plans, Symbols, and Schedules

3 Electrical Theory & Fundamentals

3.1 Ohm's Law, Power, and Series/Parallel Circuits 3.2 Conductors, Resistance, and Voltage Drop 3.3 Three-Phase Systems and Power Factor

4 Services & Service Equipment

4.1 Service Entrance Conductors and Service Point 4.2 Service Disconnecting Means 4.3 Grounding Electrode Systems for Services 4.4 Service Load Calculations

5 Separately Derived Systems & Feeders

5.1 Separately Derived Systems 5.2 Feeder Sizing, Ampacity, and Tap Rules 5.3 Feeder Load Calculations

6 Branch Circuits & Receptacles

6.1 Branch Circuit Sizing and Conductor Selection 6.2 Receptacle Spacing and Required Outlets 6.3 GFCI and AFCI Requirements 6.4 Lighting Outlets and Switch-Controlled Circuits

7 Overcurrent Protection

7.1 Overcurrent Principles and OCPD Types 7.2 Small-Conductor and Continuous-Load Rules 7.3 Motor Overcurrent and Short-Circuit Protection

8 Wiring Methods, Conductors & Boxes

8.1 Wiring Methods and Raceways 8.2 Conductor Insulations and Ampacity 8.3 Conduit and Raceway Fill 8.4 Boxes and Box Fill 8.5 Cable Trays and Underground Wiring 8.6 Cabinets, Cutout Boxes, and Panelboards

9 Equipment Grounding & Bonding

9.1 Equipment Grounding Conductors 9.2 Bonding & the Effective Ground-Fault Current Path 9.3 Equipment and Box Grounding Connections

10 Equipment, Devices & Transformers

10.1 Luminaires and Lighting (NEC Article 410) 10.2 Switches and Device Wiring (NEC Articles 404 & 400) 10.3 Appliances and Utilization Equipment (NEC Articles 422 & 424) 10.4 Transformers (NEC Article 450) 10.5 Working Space and Equipment Access (NEC 110.26)

11 Motors & Generators

11.1 Motor Branch Circuits & Conductors 11.2 Motor Disconnects, Controllers & Starters 11.3 Generators & Emergency Systems

12 Control Devices & Disconnecting Means

12.1 General Disconnecting Means Principles 12.2 HVAC and Refrigeration Disconnects 12.3 Motor Control Circuits and VFDs

13 Dwelling Load Calculations

13.1 General Lighting and Receptacle Load 13.2 Appliance, Range, and Dryer Load 13.3 Neutral Load and Service Sizing

14 Commercial & Advanced Calculations

14.1 Commercial Lighting and Receptacle Load 14.2 Continuous Loads and Equipment Demand 14.3 Voltage Drop and Conductor Sizing 14.4 Commercial Building Load Capstone

15 Special Occupancies & Conditions

15.1 Hazardous (Classified) Locations — NEC Articles 500–506 15.2 Health Care Facilities — NEC Article 517 15.3 Pools, Spas, and Fountains — NEC Article 680 (Beyond GFCI) 15.4 Other Specific Occupancies — A Survey 15.5 Data Processing Rooms and Communications Systems

16 Renewable Energy Technologies

16.1 Solar PV Systems (Article 690) 16.2 Energy Storage and EV Charging (Articles 706, 625)

17 Exam Strategy & Final Review

17.1 Time Management and NEC Lookup Speed 17.2 Test Day and Final Practice

1.1 About the Texas Journeyman Electrician Exam

Key Takeaways Explain This Topic AI

The Texas Journeyman Electrician exam is administered by PSI Services LLC under contract with the Texas Department of Licensing and Regulation (TDLR) and, since September 1, 2026, is referenced to the 2026 NEC.

In TDLR FY2025 just 24.46% of NEC Knowledge attempts (1,402 of 5,731) and 20.56% of Calculations attempts (1,301 of 6,328) passed — the Calculations portion is the harder gate.

The exam is open-book: the only reference is a soft-bound NEC (PSI permits any edition, but tests the 2026 edition); the NEC Handbook, loose-leaf, spiral, and ring-bound editions are prohibited.

Passing earns the legal authority to pull permits under a Master Electrician and to supervise unlicensed workers on commercial and residential jobs in Texas.

If you fail only one portion you keep the passing portion and retake just the failed one; PSI charges the same $78 retake fee for one portion or both.

Last updated: October 2026

What the Texas Journeyman Electrician Exam Is

Quick Answer: The Texas Journeyman Electrician exam is an open-book licensure test administered by PSI Services LLC under contract with the Texas Department of Licensing and Regulation (TDLR) . It is based on the 2026 National Electrical Code (NEC) and consists of 85 items (80 of them scored) split across two separately-scored portions. You must score 70% on each portion to pass. In TDLR FY2025 — the first fiscal year to include the two-part format — 1,402 of 5,731 NEC Knowledge attempts passed ( 24.46% ) and only 1,301 of 6,328 Calculations attempts passed ( 20.56% ) — making it one of the hardest electrical exams in the United States. If you fail only one portion, you retake only that portion.

The Texas Journeyman Electrician license is the state credential that authorizes a person to install, alter, repair, and supervise the installation of electrical wiring, fixtures, and apparatus under the employment of a Texas-licensed Master Electrician . Without this license, an individual may only perform electrical work as an apprentice under direct supervision, or as a Master Electrician if they hold that higher credential. The journeyman tier is the workhorse of the Texas electrical trade — the person on the ladder pulling conduit, landing conductors, and making the code-compliant decisions that keep buildings safe.

Who Administers It

Two organizations share responsibility for the exam:

Role Entity What They Do

Regulator Texas Department of Licensing and Regulation (TDLR) Sets eligibility rules, approves applications, issues licenses, publishes pass-rate statistics

Test Vendor PSI Services LLC Delivers the exam at PSI centers in 16 Texas cities, collects the $78 exam fee, reports scores immediately

TDLR is an independent Texas state agency, governed by the Texas Commission of Licensing and Regulation, that enforces the state's electrical licensing law (Texas Occupations Code Chapter 1305 and 16 Texas Administrative Code Chapter 73). PSI is the private vendor TDLR contracts to handle test scheduling, proctoring, and score reporting. You apply to TDLR for eligibility; you schedule and sit the exam with PSI.

The 2026 NEC Basis

Every question on the current exam is written against the 2026 edition of the NFPA 70 National Electrical Code , which TDLR adopted as the Texas electrical code effective September 1, 2026 (16 TAC §73.100). The NEC is updated on a three-year cycle, and Texas adopts each new edition by rule. The 2026 NEC is the reference for both the NEC Knowledge and Calculations parts of the exam, and a soft-bound NEC is the only reference book permitted in the testing room.

The exam is open-book , but with strict limits. Bring a soft-bound 2026 NEC — no loose-leaf, spiral-bound, or ring-bound copies, and no NEC Handbook (the Handbook contains explanatory commentary that the exam does not test). PSI's bulletin says any soft-bound edition may be brought, but the questions are based on the TDLR-adopted 2026 edition, so an older book will point you to the wrong section numbers. Publisher-supplied tabs and pre-existing highlighter marks are allowed; homemade adhesive tabs and any writing during the exam are not. You will not have time to look up every answer, so knowing the structure of the NEC — Chapter, Article, Section, Table — is as important as knowing the content.

Why the Pass Rate Is So Low

These pass rates are not typos. TDLR publishes exam statistics every fiscal year, and in FY2025 it reported the two portions separately for the first time: 5,731 NEC Knowledge attempts with 1,402 passes (24.46%) and 6,328 Calculations attempts with 1,301 passes (20.56%) . The Calculations portion is measurably the harder gate. (For historical comparison, the last full year of the old single blended exam — FY2024 — ran at 27.86%, or 2,365 passes out of 8,490 attempts.) Several factors drive the failure rate:

The two-part split requires 70% on each portion independently. A candidate who aces the 59-item NEC Knowledge portion but stumbles on the 26-item Calculations portion does not earn the license until the Calculations portion is retaken and passed.

Time pressure is severe — roughly 2.2 minutes per question on Knowledge and 4.2 minutes on Calculations, but calculation questions demand multi-step Ohm's Law, conductor sizing, and motor full-load current lookups.

Code fluency is tested, not memorization. You must locate the right Article and apply its exception or condition, not recite it.

The NEC is dense. At roughly 900 pages, with cross-references that hop between Chapter 2 (wiring), Chapter 3 (methods), Chapter 4 (equipment), and the Special Occupancies in Chapters 5–7, a candidate who cannot navigate quickly will run out of time.

Why This Exam Matters for Licensure

Passing the journeyman exam is a legal prerequisite to working unsupervised as an electrician in Texas. With the license you may:

  • Pull permits under a Master Electrician's signature
  • Supervise unlicensed apprentices and helpers on the job site

Perform electrical work anywhere in the state without holding a separate local license (state law preempts most local licensing)

Progress toward the Master Electrician credential, which requires 12,000 total hours of on-the-job training, at least two years holding a journeyman license, and a separate two-part exam

Without the license, you are limited to apprentice-level work, cannot legally supervise others, and cannot serve as the responsible electrician on a job. For most electricians in Texas, the journeyman exam is the single highest-leverage credential in their career.

Exam Facts at a Glance

  • Detail Value
  • Regulator Texas Department of Licensing and Regulation (TDLR)
  • Test Vendor PSI Services LLC
  • Code Basis 2026 NEC (soft-bound only)
  • Total Questions 85 items (59 Knowledge + 26 Calculations); 80 scored
  • Total Time 240 minutes (4 hours)
  • Knowledge Part 59 questions, 130 minutes
  • Calculations Part 26 questions, 110 minutes
  • Passing Score 70% on EACH part independently
  • Exam Fee $78 (covers both portions; retake $78 for one portion or both)
  • Application Fee $30 non-refundable to TDLR
  • Format Open-book, multiple-choice, proctored at a PSI test center
  • Languages English and Spanish

Results Immediate — the PSI proctor hands you a score report at the test center; PSI reports the official result to TDLR electronically

  • FY2025 Pass Rate — NEC Knowledge 24.46% (1,402 pass / 5,731 attempts)
  • FY2025 Pass Rate — Calculations 20.56% (1,301 pass / 6,328 attempts)
  • The 10-Area Content Outline

The PSI Candidate Information Bulletin publishes a ten-area content outline with an exact item count for each area on each portion. Both portions sample all ten areas. The table below is the real weighting — study time should follow these counts, not intuition.

  • # Subject area (CIB wording) Knowledge Calculations Total
  • 1 Definitions, Theory, and Plans (Calculations and Theory) 3 2 5
  • 2 Electrical Services, Service Equipment, and Separately Derived Systems 6 4 10
  • 3 Electrical Feeders 3 3 6
  • 4 Branch Circuits and Conductors (Branch Circuit Calculations and Conductors) 10 4 14
  • 5 Electrical Wiring Methods and Electrical Materials 10 2 12
  • 6 Electrical Equipment and Devices 10 2 12
  • 7 Motors and Generators 5 2 7
  • 8 Electrical Control Devices and Disconnecting Means 1 1 2
  • 9 Special Occupancies, Equipment, and Conditions 6 3 9
  • 10 Renewable Energy Technologies 2 1 3
  • Scored items 56 24 80

Three patterns fall out of the numbers. Branch Circuits and Conductors is the single biggest area at 14 of 80 scored items , followed by Wiring Methods and Equipment/Devices at 12 each — those three areas alone are just under half the exam. On the Calculations portion the heaviest areas are Services (4 items) and Branch Circuit Calculations (4 items) , not motors. And Control Devices and Disconnecting Means is only 2 items total — real, but not worth days of study.

This guide follows that outline. Each subsequent chapter maps to one or more of these areas, with NEC article references and worked examples matched to what the exam actually tests.

A Note on the 2026 NEC Transition

The exam used the 2023 NEC through August 31, 2026. TDLR adopted the 2026 NEC as the Texas electrical code effective September 1, 2026 (16 TAC §73.100), and the PSI Candidate Information Bulletin (updated 9/15/2026) states that the examinations are referenced to the 2026 NEC from that date. Texas made one change to the model code: outlets supplying listed outdoor HVAC equipment keep the 210.8(F) Exception No. 2 GFCI exemption, which TDLR extended without an expiration date.

The principal lookup changes for this exam are:

Load calculations are in Article 120 , formerly Article 220. Dwelling feeder/service lighting uses 2 VA/ft² under 120.41; the minimum branch-circuit count still uses 3 VA/ft² under 120.13.

120.5(E) separates the load sum from continuous-load conductor and overcurrent sizing. Do not insert an extra blanket 125% multiplier into an Article 120 load calculation.

General-use snap switches and dimmers are in Article 406, Part III . Article 404 continues to cover other switches and disconnects.

Chapter 8 no longer has its former independence. Start limited-energy installation lookups with Articles 720–750 and use Chapter 8 for communications outside and entering buildings.

Texas retains its specific outdoor HVAC exception to 210.8(F) . Other covered outdoor dwelling outlets use the new 60 A threshold.

Use the 2026 index and table notes when working a problem. A correct old-edition answer may have a different location or value in this edition.

Sources: PSI Electrician Candidate Information Bulletin , TDLR rule adoption notice , and NFPA: Key Changes in the 2026 NEC .