Study guide

2.3 NEC Index and Quick Lookup Strategies

Texas Journeyman Electrician License Exam Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the Texas Journeyman Electrician Exam 1.2 The Two-Part Exam Format (Knowledge + Calculations) 1.3 Eligibility, Application & Scheduling

2 NEC Structure & Navigation

2.1 Key NEC Definitions (Article 100) 2.2 How the NEC is Organized 2.3 NEC Index and Quick Lookup Strategies 2.4 Reading Electrical Plans, Symbols, and Schedules

3 Electrical Theory & Fundamentals

3.1 Ohm's Law, Power, and Series/Parallel Circuits 3.2 Conductors, Resistance, and Voltage Drop 3.3 Three-Phase Systems and Power Factor

4 Services & Service Equipment

4.1 Service Entrance Conductors and Service Point 4.2 Service Disconnecting Means 4.3 Grounding Electrode Systems for Services 4.4 Service Load Calculations

5 Separately Derived Systems & Feeders

5.1 Separately Derived Systems 5.2 Feeder Sizing, Ampacity, and Tap Rules 5.3 Feeder Load Calculations

6 Branch Circuits & Receptacles

6.1 Branch Circuit Sizing and Conductor Selection 6.2 Receptacle Spacing and Required Outlets 6.3 GFCI and AFCI Requirements 6.4 Lighting Outlets and Switch-Controlled Circuits

7 Overcurrent Protection

7.1 Overcurrent Principles and OCPD Types 7.2 Small-Conductor and Continuous-Load Rules 7.3 Motor Overcurrent and Short-Circuit Protection

8 Wiring Methods, Conductors & Boxes

8.1 Wiring Methods and Raceways 8.2 Conductor Insulations and Ampacity 8.3 Conduit and Raceway Fill 8.4 Boxes and Box Fill 8.5 Cable Trays and Underground Wiring 8.6 Cabinets, Cutout Boxes, and Panelboards

9 Equipment Grounding & Bonding

9.1 Equipment Grounding Conductors 9.2 Bonding & the Effective Ground-Fault Current Path 9.3 Equipment and Box Grounding Connections

10 Equipment, Devices & Transformers

10.1 Luminaires and Lighting (NEC Article 410) 10.2 Switches and Device Wiring (NEC Articles 404 & 400) 10.3 Appliances and Utilization Equipment (NEC Articles 422 & 424) 10.4 Transformers (NEC Article 450) 10.5 Working Space and Equipment Access (NEC 110.26)

11 Motors & Generators

11.1 Motor Branch Circuits & Conductors 11.2 Motor Disconnects, Controllers & Starters 11.3 Generators & Emergency Systems

12 Control Devices & Disconnecting Means

12.1 General Disconnecting Means Principles 12.2 HVAC and Refrigeration Disconnects 12.3 Motor Control Circuits and VFDs

13 Dwelling Load Calculations

13.1 General Lighting and Receptacle Load 13.2 Appliance, Range, and Dryer Load 13.3 Neutral Load and Service Sizing

14 Commercial & Advanced Calculations

14.1 Commercial Lighting and Receptacle Load 14.2 Continuous Loads and Equipment Demand 14.3 Voltage Drop and Conductor Sizing 14.4 Commercial Building Load Capstone

15 Special Occupancies & Conditions

15.1 Hazardous (Classified) Locations — NEC Articles 500–506 15.2 Health Care Facilities — NEC Article 517 15.3 Pools, Spas, and Fountains — NEC Article 680 (Beyond GFCI) 15.4 Other Specific Occupancies — A Survey 15.5 Data Processing Rooms and Communications Systems

16 Renewable Energy Technologies

16.1 Solar PV Systems (Article 690) 16.2 Energy Storage and EV Charging (Articles 706, 625)

17 Exam Strategy & Final Review

17.1 Time Management and NEC Lookup Speed 17.2 Test Day and Final Practice

2.3 NEC Index and Quick Lookup Strategies

Key Takeaways Explain This Topic AI

With 59 questions in 130 minutes (~2.2 min/question), a systematic lookup strategy—index first, then table of contents, then tabbed articles—is the difference between passing and running out of time

The NEC Index lists keywords alphabetically and gives article/section numbers; but many exam-tested terms are defined in Article 100, not the Index, so check Article 100 first for definition questions

Tabbing the top 10 most-tested articles (210, 120, 240, 250, 300, 310, 314, 430, 230, 110) with publisher-produced tabs saves 20–30 seconds per lookup, which compounds across 59 questions

PSI permits publisher tabs and pre-existing highlights in the soft-bound 2026 NEC; homemade tabs, handwritten notes, and the NEC Handbook are NOT allowed in the exam room

Time-budget tactic: answer all questions you know first, flag the ones requiring lookup, then return to them with remaining time—never spend 5+ minutes on a single question when three others await

Last updated: October 2026

Why Lookup Strategy Determines Pass or Fail

The TX Journeyman NEC Knowledge part is 59 questions in 130 minutes. That is approximately 2 minutes and 12 seconds per question . On the open-book exam, a significant fraction of those questions are pure lookups: "What is the minimum burial depth for direct-buried PVC conduit?" or "What is the ampacity of 6 AWG copper THWN in the 75°C column?" If you spend 4 minutes flipping through the Index on each lookup question, you will run out of time before you reach question 50. A disciplined lookup strategy—Index → Table of Contents → tabs—can cut your average lookup time to 45–60 seconds, buying you time for the harder application questions.

The NEC Index: Your Primary Keyword Tool

The NEC Index (at the back of the book) is an alphabetical keyword listing that maps terms to article and section numbers. It is the fastest tool when you know the topic keyword but not the article number.

How to use the Index effectively:

Identify the most specific keyword in the question. If the question asks about GFCI protection for receptacles in a dwelling unit garage, your keyword is "GFCI" or "Ground-Fault Circuit Interrupter."

Look it up alphabetically. The Index entry for "Ground-Fault Circuit Interrupter" will list multiple section references (210.8, 215.9, 230.95, etc.).

Pick the reference that matches the scenario. If the question is about a dwelling unit, 210.8 is the correct entry because 210.8 specifically covers dwelling units.

Turn to that section and scan for the specific rule.

Common Index traps:

Terms defined in Article 100, not the Index. Some exam questions ask for a definition ("What is a separately derived system?"). The Index may not have a direct entry for every defined term. For definition questions, go to Article 100 first—it is the definitions article and is alphabetized internally.

Synonym confusion. The Index uses NEC-specific terminology. If you look up "outlet box," you may not find it; the NEC term is "outlet, device, pull, and junction boxes" (Article 314). Learn the NEC's preferred terms.

Multiple references. A single Index keyword can point to 10+ sections. Read the sub-entries carefully. "Boxes—outlet, device, pull, and junction" has sub-entries for construction, fill calculations, mounting, number of conductors, etc. Pick the sub-entry that matches your question.

"Conduit" vs. "Raceway."" The NEC uses "raceway" as the general term. If you look up "conduit," you will find entries, but the broader rules are under "Raceway." When in doubt, try both.

The Table of Contents: Subject-Area Navigation

The Table of Contents (at the front of the book) organizes by chapter and article scope . Use it when you know the subject area but not the specific keyword. For example, if a question asks about motor conductor sizing, the Index keyword "motor" yields dozens of references. The Table of Contents tells you that Article 430 covers motors, motor circuits, and controllers, so you can go straight to the article and scan its Part headings to find "Part III — Conductors" (430.22).

The Table of Contents is also the fastest route to Tables . Chapter 9 Tables are listed by number (Table 1, Table 4, Table 5, Table 8, etc.). Annex C tables are listed by raceway type (Annex C, Table C.1 for Electrical Metallic Tubing, C.2 for FMC, etc.). Knowing the Table of Contents layout saves you from hunting through 100+ pages of Annex C.

The Top 10 Most-Tested Articles — Tab Them All

Based on the TDLR 10-area content outline and the exam's emphasis on residential and commercial wiring, these ten articles generate the majority of exam questions. If you tab nothing else, tab these:

Rank Article Title Why It Is High-Frequency

1 210 Branch Circuits Receptacle spacing, GFCI/AFCI, branch-circuit ratings, continuous loads—the bread and butter of residential and commercial wiring.

2 250 Grounding and Bonding EGC sizing, grounding electrode system, service grounding, separately derived system grounding, bonding—arguably the most heavily tested article on the entire exam.

3 120 Branch-Circuit, Feeder, and Service Load Calculations Dwelling unit load calculations, demand factors, neutral load, feeder sizing—the bridge between the Knowledge and Calculations parts.

4 240 Overcurrent Protection OCPD ratings, tap rules, 240.4(D) small-conductor rules, 240.6 standard sizes—appears in almost every conductor/OCPD question.

5 310 Conductors for General Wiring Table 310.16 ampacities, temperature ratings, adjustment and correction factors, 310.15(C) conductor fill—every conductor-sizing question starts here.

6 300 Wiring Methods General requirements for wiring methods, securing and supporting, 300.4 protection, 300.5 underground installations—foundational for Chapter 3.

7 314 Outlet, Device, Pull, and Junction Boxes Box fill calculations (Table 314.16), box mounting, number of conductors—appears in nearly every box-related question.

8 430 Motors, Motor Circuits, and Controllers Motor FLC (Table 430.250), conductor sizing (430.22), OCPD sizing (430.52), motor disconnects—high-frequency on the motors content area.

9 230 Services Service conductor sizing, service disconnect, service equipment, grounding at service—critical for the services content area.

10 110 Requirements for Electrical Installations Working clearances (110.26), dedicated equipment space (110.26(E)), termination temperature ratings (110.14(C))—cited across many question types.

Tab Strategies Permitted in the Exam

PSI enforces strict rules on what you may bring into the exam room:

Permitted: Soft-bound 2026 NEC with publisher-produced tabs (e.g., NFPA tabs, Mike Holt tabs, or other commercially printed tabs) and pre-existing highlights made before the exam.

NOT permitted: Homemade tabs (cut from paper or sticky notes), handwritten notes, the NEC Handbook (which contains commentary and illustrations not in the standard NEC), loose-leaf or spiral-bound editions, and any writing or marking during the exam.

If you arrive with homemade tabs, the proctor will require you to remove them or will deny entry. Buy a tabbed NEC or apply publisher tabs before exam day. Color-coded publisher tabs for the top 10 articles above are the single most effective time-saver you can invest in.

Time-Budget Tactics for 59 Questions in 130 Minutes

Three-pass strategy:

Pass 1 (30 minutes): Answer every question you know immediately without opening the book. Flag the rest. Target: answer 25–30 questions in this pass.

Pass 2 (70 minutes): Work through the flagged questions using the Index, Table of Contents, and tabs. Budget 2 minutes per question . If a question exceeds 3 minutes, flag it again and move on.

Pass 3 (30 minutes): Return to the hardest flagged questions. Use the remaining time to verify answers you are unsure about and to tackle questions requiring multi-step lookups (e.g., a question that requires Table 310.16, then a temperature correction factor from Table 310.15(B)(1), then an adjustment factor from 310.15(C)).

Common time traps:

Spending 5+ minutes on a single raceway-fill question. These are multi-step (count conductors, pick the table, apply fill percentage). If you are not confident, mark your best guess, flag it, and return.

Reading the full text of an article when you only need one section. Use the section number from the Index; do not read the whole article.

Looking up the same article repeatedly. If you have already looked up 250.122 twice, tab it mentally and go straight there the third time.

Confusing the Index with Article 100. For definition questions, Article 100 is faster. For rule questions, the Index is faster.