Study guide

2.4 Reading Electrical Plans, Symbols, and Schedules

Texas Journeyman Electrician License Exam Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the Texas Journeyman Electrician Exam 1.2 The Two-Part Exam Format (Knowledge + Calculations) 1.3 Eligibility, Application & Scheduling

2 NEC Structure & Navigation

2.1 Key NEC Definitions (Article 100) 2.2 How the NEC is Organized 2.3 NEC Index and Quick Lookup Strategies 2.4 Reading Electrical Plans, Symbols, and Schedules

3 Electrical Theory & Fundamentals

3.1 Ohm's Law, Power, and Series/Parallel Circuits 3.2 Conductors, Resistance, and Voltage Drop 3.3 Three-Phase Systems and Power Factor

4 Services & Service Equipment

4.1 Service Entrance Conductors and Service Point 4.2 Service Disconnecting Means 4.3 Grounding Electrode Systems for Services 4.4 Service Load Calculations

5 Separately Derived Systems & Feeders

5.1 Separately Derived Systems 5.2 Feeder Sizing, Ampacity, and Tap Rules 5.3 Feeder Load Calculations

6 Branch Circuits & Receptacles

6.1 Branch Circuit Sizing and Conductor Selection 6.2 Receptacle Spacing and Required Outlets 6.3 GFCI and AFCI Requirements 6.4 Lighting Outlets and Switch-Controlled Circuits

7 Overcurrent Protection

7.1 Overcurrent Principles and OCPD Types 7.2 Small-Conductor and Continuous-Load Rules 7.3 Motor Overcurrent and Short-Circuit Protection

8 Wiring Methods, Conductors & Boxes

8.1 Wiring Methods and Raceways 8.2 Conductor Insulations and Ampacity 8.3 Conduit and Raceway Fill 8.4 Boxes and Box Fill 8.5 Cable Trays and Underground Wiring 8.6 Cabinets, Cutout Boxes, and Panelboards

9 Equipment Grounding & Bonding

9.1 Equipment Grounding Conductors 9.2 Bonding & the Effective Ground-Fault Current Path 9.3 Equipment and Box Grounding Connections

10 Equipment, Devices & Transformers

10.1 Luminaires and Lighting (NEC Article 410) 10.2 Switches and Device Wiring (NEC Articles 404 & 400) 10.3 Appliances and Utilization Equipment (NEC Articles 422 & 424) 10.4 Transformers (NEC Article 450) 10.5 Working Space and Equipment Access (NEC 110.26)

11 Motors & Generators

11.1 Motor Branch Circuits & Conductors 11.2 Motor Disconnects, Controllers & Starters 11.3 Generators & Emergency Systems

12 Control Devices & Disconnecting Means

12.1 General Disconnecting Means Principles 12.2 HVAC and Refrigeration Disconnects 12.3 Motor Control Circuits and VFDs

13 Dwelling Load Calculations

13.1 General Lighting and Receptacle Load 13.2 Appliance, Range, and Dryer Load 13.3 Neutral Load and Service Sizing

14 Commercial & Advanced Calculations

14.1 Commercial Lighting and Receptacle Load 14.2 Continuous Loads and Equipment Demand 14.3 Voltage Drop and Conductor Sizing 14.4 Commercial Building Load Capstone

15 Special Occupancies & Conditions

15.1 Hazardous (Classified) Locations — NEC Articles 500–506 15.2 Health Care Facilities — NEC Article 517 15.3 Pools, Spas, and Fountains — NEC Article 680 (Beyond GFCI) 15.4 Other Specific Occupancies — A Survey 15.5 Data Processing Rooms and Communications Systems

16 Renewable Energy Technologies

16.1 Solar PV Systems (Article 690) 16.2 Energy Storage and EV Charging (Articles 706, 625)

17 Exam Strategy & Final Review

17.1 Time Management and NEC Lookup Speed 17.2 Test Day and Final Practice

2.4 Reading Electrical Plans, Symbols, and Schedules

Key Takeaways Explain This Topic AI

The PSI content outline lists Plan Reading as one of three sub-topics inside "Definitions, Theory, and Plans" on the NEC Knowledge portion, so expect at least one drawing-based item.

Electrical symbols are not defined by the NEC — always read the drawing's legend, because a solid triangle can mean a special-purpose outlet on one set and an exit sign on another.

At the common residential scale of 1/4 in. = 1 ft-0 in., every inch measured on the plan represents 4 feet, so a 3 in. x 4.5 in. room is 12 ft x 18 ft (216 sq ft).

Homerun arrows carry the panel and circuit designation ("A-12" = panel A, circuit 12); tick marks on the arrow count conductors, per the legend on that drawing.

A panel schedule states the bus rating, main device, voltage/phase/wire configuration, and per-phase connected VA — enough to run a feeder calculation without seeing the building.

Last updated: October 2026

Why Plan Reading Sits in Area 1

The PSI Candidate Information Bulletin puts Plan Reading in the very first subject area of the NEC Knowledge portion, Definitions, Theory, and Plans , worth 3 scored items. That is a small slice, but it is a slice most candidates skip entirely because it is the only part of the exam that is not a code lookup. The drawings PSI uses are deliberately simple — a partial floor plan, a one-line, or a panel schedule — and the question always converts the drawing into a number the NEC can act on: a square footage for 120.41 , an outlet count for 210.52 , or a connected load for a feeder.

The skill is not draftsmanship. It is knowing which of the four drawing types you are looking at and what each one is allowed to tell you.

The Four Drawing Types You Will See

Drawing What it shows What the exam asks from it

Floor plan (power/lighting plan) Scaled overhead view of a level with devices, luminaires, and homeruns Square footage, device counts, circuit assignments

One-line (single-line) diagram Whole distribution system drawn as one line per feeder Service size, transformer kVA, OCPD ratings, where the main bonding jumper lands

Riser diagram Vertical distribution between floors, not to scale Feeder routing and count, panel hierarchy

Schedules (panel, luminaire, equipment) Tabulated data for one piece of equipment Bus rating, connected VA, breaker sizes, nameplate values

A one-line and a riser are diagrams , not scaled views — you can never measure a length off them. Only the floor plan carries a scale.

Reading the Scale

Architectural scales are written as drawing inches = real feet . Residential plans are almost always 1/4 in. = 1 ft-0 in. ; commercial plans are usually 1/8 in. = 1 ft-0 in.

At 1/4 in. = 1 ft-0 in., 1 inch on paper = 4 feet of building.

At 1/8 in. = 1 ft-0 in., 1 inch on paper = 8 feet of building.

So a room that measures 3 in. by 4.5 in. at 1/4 in. scale is 12 ft by 18 ft = 216 sq ft . Feed that into 120.41 and the general lighting load for that space is 216 x 2 VA = 432 VA .

Two traps show up repeatedly. First, dimension strings on the plan always beat your ruler — if the drawing is labeled 12'-0", use 12 feet even if your measurement says otherwise, because plans get reduced when printed. Second, 120.5(C) tells you what area to count : the floor area is computed from the outside dimensions of the dwelling, and since the 2023 NEC that area includes attached garages and unfinished spaces adaptable for future use, but not open porches or carports.

Symbols and the Legend

The NEC does not standardize electrical symbols. The common reference is ANSI/IEEE 315, but every design firm modifies it, which is why every drawing set carries a legend. Read it first, every time.

  • Common symbol Usual meaning
  • Circle with two parallel bars Duplex receptacle
  • Same symbol with "GFCI" or "GFI" GFCI-protected receptacle
  • Circle with two bars and a triangle/label Special-purpose outlet (range, dryer, EVSE)
  • S Single-pole switch
  • S3 / S4 Three-way / four-way switch
  • Circle with cross-hairs Surface or pendant luminaire
  • Circle in a square Recessed luminaire
  • Filled rectangle with hatching Panelboard
  • Arrow with tick marks and a code Homerun to a panel
  • Homeruns and Circuit Designations

A homerun is the arrow that leaves a device and points toward its panel. It carries two pieces of information:

The designation , such as A-12 — panel A, circuit 12. Two numbers ( A-12,14 ) mean two circuits share the run and therefore share a neutral unless the legend says otherwise.

The tick marks crossing the arrow, which count conductors. Three ticks on a 120 V branch circuit normally means two ungrounded conductors plus a neutral, with the equipment grounding conductor not counted. The legend controls this — some firms tick the EGC, some do not.

Panel Schedules

A panel schedule is a table, and the exam treats it as a data source. The header block gives you everything you need to size upstream: bus rating (e.g. 225 A), main device (200 A main breaker or main lugs only), voltage/phase/wire (120/240 V 1-phase 3-wire, or 208Y/120 V 3-phase 4-wire), AIC rating , and mounting (surface or flush).

The body lists circuits with odd numbers down the left and even numbers down the right, each with a breaker size, pole count, description, and connected VA assigned to a phase. Totalling the VA columns and dividing by the phase voltage gives the connected amperes; applying the Article 120 demand factors gives the calculated load that sizes the feeder.

How the Exam Frames It

Expect a short stem plus a simple graphic. Typical framings:

"The partial plan shows a dwelling kitchen countertop 12 ft long with no separations. What is the minimum number of 20 A small-appliance receptacle outlets required along it?" — count 2 ft increments per 210.52(C)(1) and remember the two-circuit minimum of 210.52(B)(1).

"The floor plan of a dwelling measures 40 ft x 60 ft to the outside of the exterior walls. What is the general lighting load?" — 2,400 sq ft x 2 VA = 4,800 VA per 120.41.

"The panel schedule shows panel B fed from panel A. Which drawing shows the feeder route between them?" — the riser diagram .

None of these require drafting knowledge. They require you to identify the drawing, apply the scale or the legend, and hand the result to the correct NEC article.