Study guide
7.1 Overcurrent Principles and OCPD Types
Texas Journeyman Electrician License Exam Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the Texas Journeyman Electrician Exam 1.2 The Two-Part Exam Format (Knowledge + Calculations) 1.3 Eligibility, Application & Scheduling
2 NEC Structure & Navigation
2.1 Key NEC Definitions (Article 100) 2.2 How the NEC is Organized 2.3 NEC Index and Quick Lookup Strategies 2.4 Reading Electrical Plans, Symbols, and Schedules
3 Electrical Theory & Fundamentals
3.1 Ohm's Law, Power, and Series/Parallel Circuits 3.2 Conductors, Resistance, and Voltage Drop 3.3 Three-Phase Systems and Power Factor
4 Services & Service Equipment
4.1 Service Entrance Conductors and Service Point 4.2 Service Disconnecting Means 4.3 Grounding Electrode Systems for Services 4.4 Service Load Calculations
5 Separately Derived Systems & Feeders
5.1 Separately Derived Systems 5.2 Feeder Sizing, Ampacity, and Tap Rules 5.3 Feeder Load Calculations
6 Branch Circuits & Receptacles
6.1 Branch Circuit Sizing and Conductor Selection 6.2 Receptacle Spacing and Required Outlets 6.3 GFCI and AFCI Requirements 6.4 Lighting Outlets and Switch-Controlled Circuits
7 Overcurrent Protection
7.1 Overcurrent Principles and OCPD Types 7.2 Small-Conductor and Continuous-Load Rules 7.3 Motor Overcurrent and Short-Circuit Protection
8 Wiring Methods, Conductors & Boxes
8.1 Wiring Methods and Raceways 8.2 Conductor Insulations and Ampacity 8.3 Conduit and Raceway Fill 8.4 Boxes and Box Fill 8.5 Cable Trays and Underground Wiring 8.6 Cabinets, Cutout Boxes, and Panelboards
9 Equipment Grounding & Bonding
9.1 Equipment Grounding Conductors 9.2 Bonding & the Effective Ground-Fault Current Path 9.3 Equipment and Box Grounding Connections
10 Equipment, Devices & Transformers
10.1 Luminaires and Lighting (NEC Article 410) 10.2 Switches and Device Wiring (NEC Articles 404 & 400) 10.3 Appliances and Utilization Equipment (NEC Articles 422 & 424) 10.4 Transformers (NEC Article 450) 10.5 Working Space and Equipment Access (NEC 110.26)
11 Motors & Generators
11.1 Motor Branch Circuits & Conductors 11.2 Motor Disconnects, Controllers & Starters 11.3 Generators & Emergency Systems
12 Control Devices & Disconnecting Means
12.1 General Disconnecting Means Principles 12.2 HVAC and Refrigeration Disconnects 12.3 Motor Control Circuits and VFDs
13 Dwelling Load Calculations
13.1 General Lighting and Receptacle Load 13.2 Appliance, Range, and Dryer Load 13.3 Neutral Load and Service Sizing
14 Commercial & Advanced Calculations
14.1 Commercial Lighting and Receptacle Load 14.2 Continuous Loads and Equipment Demand 14.3 Voltage Drop and Conductor Sizing 14.4 Commercial Building Load Capstone
15 Special Occupancies & Conditions
15.1 Hazardous (Classified) Locations — NEC Articles 500–506 15.2 Health Care Facilities — NEC Article 517 15.3 Pools, Spas, and Fountains — NEC Article 680 (Beyond GFCI) 15.4 Other Specific Occupancies — A Survey 15.5 Data Processing Rooms and Communications Systems
16 Renewable Energy Technologies
16.1 Solar PV Systems (Article 690) 16.2 Energy Storage and EV Charging (Articles 706, 625)
17 Exam Strategy & Final Review
17.1 Time Management and NEC Lookup Speed 17.2 Test Day and Final Practice
7.1 Overcurrent Principles and OCPD Types
Key Takeaways Explain This Topic AI
NEC Article 100 defines overcurrent as any current in excess of rated current, and splits it into three forms: overload, short-circuit, and ground fault.
NEC 240.6(A) standard ampere ratings run 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 80, 90, 100, 110, 125, 150, 175, 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 1000, 1200, 1600, 2000, 2500, 3000, 4000, 5000, and 6000 amperes.
Series ratings under NEC 240.8 are only valid for specific listed combinations of upstream and downstream devices; any modification requires re-evaluation of the series rating.
Dual-element (time-delay) fuses hold a large inrush temporarily then clear on sustained overload, which is why they protect motor branch circuits without nuisance tripping.
NEC 240.12 requires equipment rated over 1000 A at 600 V or less to be field-marked with available fault current, and the marking must be updated when modifications affect that value.
Last updated: August 2026
Why Overcurrent Protection Matters for the TX Journeyman Exam
Overcurrent protection is the backbone of NEC Article 240 and shows up in both halves of the Texas Journeyman exam. The NEC Knowledge part (59 questions) tests definitions, standard ampere ratings, device types, and series-combination rules. The Calculations part (26 questions) uses these same ratings when sizing branch-circuit and motor overcurrent devices. Getting 240.6(A) standard ratings and the 240.4(D) small-conductor caps wrong costs points in both sections, so this chapter is high-leverage.
The Three Forms of Overcurrent (NEC Article 100)
Overcurrent is defined in Article 100 as any current in excess of the rated current of equipment or the ampacity of a conductor . The NEC recognizes three forms, each with a different cause and clearing-time requirement.
Form Definition (Art. 100) Typical Cause Magnitude Clearing Time
Overload Operation in excess of normal, full-load current that persists long enough to damage equipment Too many loads on a circuit; a stalled motor 1× to 6× FLC Seconds to minutes
Short-circuit An unintended connection between ungrounded conductors of different phases/polarities Insulation failure phase-to-phase Hundreds to thousands of A Must clear in cycles
Ground fault An unintended connection between an ungrounded conductor and a grounded surface Insulation nick touching conduit or a box Tens to thousands of A Must clear in cycles
A motor stalling and drawing 3× full-load current is an overload . A phase conductor welding to another phase in a J-box is a short-circuit . That same conductor touching the grounded raceway is a ground fault . All three are overcurrent, but a device that handles one well (a motor overload relay) is not necessarily rated to interrupt another (a short-circuit).
OCPD Types — Fuses vs Circuit Breakers
NEC 240.2 defines an overcurrent protective device (OCPD) as a device capable of opening a circuit at a predetermined overcurrent. Two families are recognized.
Fuses
A fuse is a single-use device that contains a calibrated element designed to melt and open the circuit under overcurrent. The NEC recognizes several varieties.
Plug fuses (Edison-base and Type S) — used on circuits of 125 V or less to ground, 30 A or less. Governed by NEC 240.5. Type S plugs are rejection-base so the wrong size cannot be installed.
Cartridge fuses — ferrule (up to 60 A) and knife-blade (60 A and larger), used in disconnect switches and panelboards.
Non-time-delay (one-time) fuses — a single element that opens quickly; good for incandescent lighting and resistive loads but they blow on motor inrush.
Dual-element (time-delay) fuses — two elements in one tube: a short-circuit element that clears fast on high fault current, and an overload element that holds a temporary inrush (typically 5× rating for up to 10 seconds) before opening. These are the standard choice for motor branch circuits per 430.52.
Circuit Breakers
A circuit breaker is a mechanical switching device that opens automatically on overcurrent and can be reset and reused.
Thermal-magnetic breakers — a bimetallic strip responds to sustained overload (the thermal part), and a magnetic solenoid responds instantaneously to short-circuit/ground-fault current. The standard residential and commercial breaker.
Magnetic-only (instantaneous-trip) breakers — no thermal element; used as the short-circuit/ground-fault element in a motor combination starter where a separate overload relay (430.32) handles the sustained-overload function. Listed under 430.52 as "instantaneous trip breaker."
Intermittent-duty / adjustable-trip breakers — allow setting the instantaneous pickup, common on larger motor circuits.
Fuse vs Circuit Breaker at a Glance
- Attribute Fuse Circuit Breaker
- Operation Sacrificial — must be replaced after opening Resettable — re-close after clearing
- Reset time Requires stocking spares Re-close immediately
- Interrupting rating Commonly 200 kA+; check label Commonly 10–65 kA; check label
- Selectivity Easy to coordinate by ampere rating alone Requires selective coordination study (240.12)
- Initial cost Lower Higher
- Maintenance None (passive) Periodic exercise/testing
- NEC 240.5 — Lamp Holders
NEC 240.5 limits how OCPDs protect luminaires and lampholders. 240.5(B)(2) sets the maximum branch-circuit OCPD for circuits supplying medium-base lampholders at 20 A for circuits with a mix of luminaires, and at 15 A or 20 A depending on the lampholder rating. The takeaway for the exam: a 30 A or 50 A branch circuit cannot supply standard medium-base screw-shell lampholders.
NEC 240.6(A) — Standard Ampere Ratings
240.6(A) lists the standard ampere ratings used for fuses and fixed-trip circuit breakers. The exam expects you to know the list, including which values are NOT available as standard so you can size correctly under 240.4(B).
- 15 20 25 30 35 40 45 50 60 70 80 90 100 110 125
- 150 175 200 225 250 300 350 400 450 500 600 700 800 1000 1200
Ratings continue at 1600, 2000, 2500, 3000, 4000, 5000, and 6000 A.
Exam tip: 25 A and 35 A ARE standard ratings under 240.6(A), but the small-conductor rule in 240.4(D) caps 14, 12, and 10 AWG copper at 15, 20, and 30 A respectively — so you will never size a 25 A or 35 A OCPD for a 14/12/10 AWG small-conductor branch circuit. Treat 25 and 35 as "standard but rarely used for small conductors."
NEC 240.8 — Series Ratings
A series combination rating is the short-circuit current that a specific upstream-plus-downstream pair can clear together, even though the downstream device alone has a lower interrupting rating. NEC 240.8 imposes strict rules.
Only listed series combinations are permitted. You cannot pair an arbitrary 65 kAIC upstream breaker with a 10 kAIC downstream breaker and call the result a series system — the pair must be tested and listed together.
The series rating is valid only in unmodified equipment. If the installation is modified, the series combination must be re-evaluated by a qualified engineer or the equipment must be re-marked.
Series ratings are not permitted where the downstream device feeds a motor in a way that could let motor short-circuit contribution defeat the coordination (240.8(C)).
The exam will try to bait you with "any upstream breaker with a high enough kAIC protects a downstream low-kAIC breaker." That is false. The pair must be a listed combination.
NEC 240.12 — Available Fault Current and Selective Coordination
NEC 240.12 has two prongs.
Available fault current marking. Equipment rated over 1000 A at 600 V or less must be field-marked with the available fault current at the line terminals. The marking must be re-evaluated whenever modifications change the available fault current.
Selective coordination. Where an orderly shutdown is required (690, 700, 701, 702 systems; life safety; critical operations), OCPDs must be selectively coordinated so that only the device closest to the fault opens — upstream devices stay closed. Coordination is typically studied on a time-current curve overlay and may require setting adjustments or fuse-only solutions in the lower range.