Study guide

15.2 Health Care Facilities — NEC Article 517

Texas Journeyman Electrician License Exam Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the Texas Journeyman Electrician Exam 1.2 The Two-Part Exam Format (Knowledge + Calculations) 1.3 Eligibility, Application & Scheduling

2 NEC Structure & Navigation

2.1 Key NEC Definitions (Article 100) 2.2 How the NEC is Organized 2.3 NEC Index and Quick Lookup Strategies 2.4 Reading Electrical Plans, Symbols, and Schedules

3 Electrical Theory & Fundamentals

3.1 Ohm's Law, Power, and Series/Parallel Circuits 3.2 Conductors, Resistance, and Voltage Drop 3.3 Three-Phase Systems and Power Factor

4 Services & Service Equipment

4.1 Service Entrance Conductors and Service Point 4.2 Service Disconnecting Means 4.3 Grounding Electrode Systems for Services 4.4 Service Load Calculations

5 Separately Derived Systems & Feeders

5.1 Separately Derived Systems 5.2 Feeder Sizing, Ampacity, and Tap Rules 5.3 Feeder Load Calculations

6 Branch Circuits & Receptacles

6.1 Branch Circuit Sizing and Conductor Selection 6.2 Receptacle Spacing and Required Outlets 6.3 GFCI and AFCI Requirements 6.4 Lighting Outlets and Switch-Controlled Circuits

7 Overcurrent Protection

7.1 Overcurrent Principles and OCPD Types 7.2 Small-Conductor and Continuous-Load Rules 7.3 Motor Overcurrent and Short-Circuit Protection

8 Wiring Methods, Conductors & Boxes

8.1 Wiring Methods and Raceways 8.2 Conductor Insulations and Ampacity 8.3 Conduit and Raceway Fill 8.4 Boxes and Box Fill 8.5 Cable Trays and Underground Wiring 8.6 Cabinets, Cutout Boxes, and Panelboards

9 Equipment Grounding & Bonding

9.1 Equipment Grounding Conductors 9.2 Bonding & the Effective Ground-Fault Current Path 9.3 Equipment and Box Grounding Connections

10 Equipment, Devices & Transformers

10.1 Luminaires and Lighting (NEC Article 410) 10.2 Switches and Device Wiring (NEC Articles 404 & 400) 10.3 Appliances and Utilization Equipment (NEC Articles 422 & 424) 10.4 Transformers (NEC Article 450) 10.5 Working Space and Equipment Access (NEC 110.26)

11 Motors & Generators

11.1 Motor Branch Circuits & Conductors 11.2 Motor Disconnects, Controllers & Starters 11.3 Generators & Emergency Systems

12 Control Devices & Disconnecting Means

12.1 General Disconnecting Means Principles 12.2 HVAC and Refrigeration Disconnects 12.3 Motor Control Circuits and VFDs

13 Dwelling Load Calculations

13.1 General Lighting and Receptacle Load 13.2 Appliance, Range, and Dryer Load 13.3 Neutral Load and Service Sizing

14 Commercial & Advanced Calculations

14.1 Commercial Lighting and Receptacle Load 14.2 Continuous Loads and Equipment Demand 14.3 Voltage Drop and Conductor Sizing 14.4 Commercial Building Load Capstone

15 Special Occupancies & Conditions

15.1 Hazardous (Classified) Locations — NEC Articles 500–506 15.2 Health Care Facilities — NEC Article 517 15.3 Pools, Spas, and Fountains — NEC Article 680 (Beyond GFCI) 15.4 Other Specific Occupancies — A Survey 15.5 Data Processing Rooms and Communications Systems

16 Renewable Energy Technologies

16.1 Solar PV Systems (Article 690) 16.2 Energy Storage and EV Charging (Articles 706, 625)

17 Exam Strategy & Final Review

17.1 Time Management and NEC Lookup Speed 17.2 Test Day and Final Practice

15.2 Health Care Facilities — NEC Article 517

Key Takeaways Explain This Topic AI

A hospital Type 1 Essential Electrical System (517.29) consists of a Life Safety Branch and a Critical Branch (plus an Equipment Branch) that must be automatically restored within 10 seconds per 517.32.

517.17 requires coordinated two-level ground-fault protection on solidly grounded wye systems over 150 V to ground (e.g., 480Y/277 V) with disconnects rated 1000 A or more, so a feeder fault trips only the feeder GFP — not the main.

517.13 requires two equipment grounding paths in patient care spaces: a qualifying metal raceway/cable armor per 250.118(A) AND a separate insulated copper EGC inside it.

517.19(B)(1) requires a minimum of 14 hospital-grade receptacles at each Category 1 (critical care) patient bed location, supplied by at least two branch circuits.

Patient care spaces use the Category 1/2/3/4 risk system in the 2023 NEC, replacing the older critical/general/basic terminology and aligning with NFPA 99.

Last updated: August 2026

Why Article 517 Matters for the TX Journeyman Exam

Health care facility wiring is one of the two topics the TX exam outline names explicitly under Area 9. Questions target the Essential Electrical System branches, the two-path equipment grounding rule, and the second level of ground-fault coordination — all pure section-number recall. Expect 2–4 questions.

Essential Electrical System (517.29)

A hospital (Category 1 patient care spaces) is supplied by a Type 1 Essential Electrical System (EES) consisting of:

  • Life Safety Branch — illumination, exit/egress, alarm, and communications loads (517.33)
  • Critical Branch — patient care-related loads, including receptacles and equipment in critical spaces (517.34)
  • Equipment Branch — major electrical equipment that can be delayed (517.35)

Per 517.32 , the Life Safety and Critical branches must be automatically connected to an alternate source (generator) so that all required functions are restored within 10 seconds of a normal power interruption. The Equipment Branch may be connected via timed-delay automatic or manual transfer.

Second Ground-Fault Coordination — 517.17

Where a health care facility is served by a solidly grounded wye system with more than 150 V to ground but not exceeding 1000 V phase-to-phase, and any disconnecting means is rated 1000 A or more (the classic 480Y/277 V service), 517.17 requires two levels of ground-fault protection of equipment (GFPE) :

A main/service GFP device.

A downstream feeder GFP sized and set so a feeder ground fault opens only the feeder — not the main.

517.17(C) demands 100% selectivity between the two levels: the feeder device, not the service device, must operate for faults on the load side of the feeder, considering all manufacturer tolerances and disconnect operating time. The objective is that a single ground fault on a feeder cannot black out the entire facility — critical for a hospital. Maximum settings are 1200 A pickup and no longer than 1 second for fault currents of 3000 A or more. (General EES coordination under 517.31(G) only requires coordination for fault durations exceeding 0.1 second, which is less stringent.)

Equipment Grounding in Patient Care Spaces — 517.13

517.13 provides redundancy so a single installation error cannot leave patient-care equipment ungrounded. It requires two separate equipment grounding paths for branch circuits serving patient care spaces (including the homerun):

517.13(A) — Mechanical path: the wiring method itself must be a metal raceway or metal cable whose armor/sheath qualifies as an EGC per 250.118(A) — RMC, IMC, EMT, Type AC cable with internal bonding strip, or listed all-purpose Type MCAP. Traditional interlocked Type MC cable does not qualify under 250.118(A)(10)(a).

517.13(B) — Wire path: an insulated copper EGC (green insulation its entire length) installed inside the raceway and connected to receptacle grounding terminals, metal boxes/enclosures, and metal parts of fixed equipment operating at more than 100 V likely to become energized. Sized per 250.122.

The 2023 NEC changed the wording from "wiring in patient care spaces" to "wiring serving patient care spaces," so the two-path rule now applies to the entire branch circuit , not just the portion physically inside the space. Patient care spaces use the Category 1/2/3/4 risk-based system (Category 1 = critical care, Category 2 = general care) replacing the older critical/general/basic/support labels.

Isolated Ground Receptacles — 517.16

Where an isolated ground receptacle is installed in a patient care space, the isolated grounding terminal must be connected to the reference grounding point by an insulated copper equipment grounding conductor . The metal raceway required by 517.13(A) still provides the second path. Isolated ground receptacles are used to reduce electrical noise on sensitive medical equipment, but they do not eliminate the 517.13 two-path requirement.

Patient Bed Location Receptacles — 517.19

For Category 1 (critical care) patient bed locations, 517.19(B)(1) requires a minimum of 14 receptacles , which may be single, duplex, or quadruplex. At least one must be supplied by the normal system branch circuit or by a critical branch served by a different transfer switch than the other receptacles at that location (517.19(A) requires at least two branch circuits). All 14 receptacles must be listed hospital grade and identified as such (517.19(B)(2)), with the grounding terminal connected to the reference grounding point by an insulated copper EGC. Operating rooms under 517.19(C)(1) require a minimum of 36 receptacles , divided between at least two branch circuits.

For comparison, Category 2 (general care) patient bed locations under 517.18(B)(1) require a minimum of 8 receptacles, not all hospital grade.