Study guide

8.5 Cable Trays and Underground Wiring

Texas Journeyman Electrician License Exam Exam

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

1.1 About the Texas Journeyman Electrician Exam 1.2 The Two-Part Exam Format (Knowledge + Calculations) 1.3 Eligibility, Application & Scheduling

2 NEC Structure & Navigation

2.1 Key NEC Definitions (Article 100) 2.2 How the NEC is Organized 2.3 NEC Index and Quick Lookup Strategies 2.4 Reading Electrical Plans, Symbols, and Schedules

3 Electrical Theory & Fundamentals

3.1 Ohm's Law, Power, and Series/Parallel Circuits 3.2 Conductors, Resistance, and Voltage Drop 3.3 Three-Phase Systems and Power Factor

4 Services & Service Equipment

4.1 Service Entrance Conductors and Service Point 4.2 Service Disconnecting Means 4.3 Grounding Electrode Systems for Services 4.4 Service Load Calculations

5 Separately Derived Systems & Feeders

5.1 Separately Derived Systems 5.2 Feeder Sizing, Ampacity, and Tap Rules 5.3 Feeder Load Calculations

6 Branch Circuits & Receptacles

6.1 Branch Circuit Sizing and Conductor Selection 6.2 Receptacle Spacing and Required Outlets 6.3 GFCI and AFCI Requirements 6.4 Lighting Outlets and Switch-Controlled Circuits

7 Overcurrent Protection

7.1 Overcurrent Principles and OCPD Types 7.2 Small-Conductor and Continuous-Load Rules 7.3 Motor Overcurrent and Short-Circuit Protection

8 Wiring Methods, Conductors & Boxes

8.1 Wiring Methods and Raceways 8.2 Conductor Insulations and Ampacity 8.3 Conduit and Raceway Fill 8.4 Boxes and Box Fill 8.5 Cable Trays and Underground Wiring 8.6 Cabinets, Cutout Boxes, and Panelboards

9 Equipment Grounding & Bonding

9.1 Equipment Grounding Conductors 9.2 Bonding & the Effective Ground-Fault Current Path 9.3 Equipment and Box Grounding Connections

10 Equipment, Devices & Transformers

10.1 Luminaires and Lighting (NEC Article 410) 10.2 Switches and Device Wiring (NEC Articles 404 & 400) 10.3 Appliances and Utilization Equipment (NEC Articles 422 & 424) 10.4 Transformers (NEC Article 450) 10.5 Working Space and Equipment Access (NEC 110.26)

11 Motors & Generators

11.1 Motor Branch Circuits & Conductors 11.2 Motor Disconnects, Controllers & Starters 11.3 Generators & Emergency Systems

12 Control Devices & Disconnecting Means

12.1 General Disconnecting Means Principles 12.2 HVAC and Refrigeration Disconnects 12.3 Motor Control Circuits and VFDs

13 Dwelling Load Calculations

13.1 General Lighting and Receptacle Load 13.2 Appliance, Range, and Dryer Load 13.3 Neutral Load and Service Sizing

14 Commercial & Advanced Calculations

14.1 Commercial Lighting and Receptacle Load 14.2 Continuous Loads and Equipment Demand 14.3 Voltage Drop and Conductor Sizing 14.4 Commercial Building Load Capstone

15 Special Occupancies & Conditions

15.1 Hazardous (Classified) Locations — NEC Articles 500–506 15.2 Health Care Facilities — NEC Article 517 15.3 Pools, Spas, and Fountains — NEC Article 680 (Beyond GFCI) 15.4 Other Specific Occupancies — A Survey 15.5 Data Processing Rooms and Communications Systems

16 Renewable Energy Technologies

16.1 Solar PV Systems (Article 690) 16.2 Energy Storage and EV Charging (Articles 706, 625)

17 Exam Strategy & Final Review

17.1 Time Management and NEC Lookup Speed 17.2 Test Day and Final Practice

8.5 Cable Trays and Underground Wiring

Key Takeaways Explain This Topic AI

A cable tray is a support system, not a raceway, so the conductors and cables inside it must themselves be a permitted wiring method under Article 392.

Table 300.5(A) column 1 requires 24 in. of cover for direct-buried cable in unspecified locations, while rigid metal and intermediate metal conduit need only 6 in. and nonmetallic raceway needs 18 in.

A 120 V, 20 A residential branch circuit with GFCI protection may be direct-buried at 12 in. of cover, and 30 V irrigation and landscape-lighting circuits at 6 in.

Under public streets, highways, roads, alleys, driveways, and parking lots every wiring method needs 24 in. of cover — there is no reduced column.

A metallic cable tray may serve as the equipment grounding conductor only under continuous maintenance and supervision, where the tray is listed and marked for that use and sized per Table 392.60(A).

Last updated: August 2026

Where These Topics Sit on the Blueprint

Electrical Wiring Methods and Electrical Materials is one of the two heaviest areas on the NEC Knowledge portion (10 scored items) and also carries 2 items on the Calculations portion. The PSI outline names five sub-topics inside it, two of which are covered here: Raceways and Cable Trays and Underground Wiring . Both are almost pure lookup — the exam wants a number or a permitted/not-permitted call, and both sit in parts of Chapter 3 that candidates rarely tab.

  • Article 392 — Cable Trays
  • A tray is not a raceway

This is the single most-tested idea in Article 392. A cable tray system is a structural support system for cables, raceways, and conductors. It does not enclose or protect conductors the way a conduit does, so whatever you lay in it must independently be a permitted wiring method. That is why you find Type MC, Type TC, Type MI, metal-clad and tray-rated cables in trays, and why you cannot simply drop loose building wire into one.

Uses permitted and not permitted

392.10 permits cable trays to support the wiring methods listed in Table 392.10(A), plus raceways, boxes, and conduit bodies.

392.10(B)(1) permits single conductors 1/0 AWG and larger in ladder, ventilated trough, or ventilated channel tray, but only where the tray is used in industrial establishments with qualified maintenance and supervision.

392.12 prohibits cable tray in hoistways and where it would be subject to severe physical damage .

Installation rules that get tested

392.18(A) — the tray system must be complete before conductors are installed.

392.18(G) — trays must be exposed and accessible, and marked so they are not used as walkways or ladders.

392.18(H) — covers are required where the tray is exposed to physical damage.

392.30(A) — cables must be secured where the tray runs vertically.

392.44 — expansion splice plates are required where thermal expansion is a factor.

392.56 — splices are permitted inside a tray provided they are accessible and do not project above the side rails. This is a genuine exception to the usual box requirement, and it is a favorite exam item.

Fill (392.22)

For multiconductor cables rated 2000 V or less in a ladder or ventilated trough tray:

Where all cables are 4/0 AWG or larger , the sum of the cable diameters may not exceed the cable tray width, and the cables must be installed in a single layer .

Where all cables are smaller than 4/0 , the sum of the cable cross-sectional areas may not exceed the maximum fill area in column 1 of Table 392.22(A) for that tray width.

Mixed installations use the combination formulas in Table 392.22(A).

Ampacity (392.80)

Multiconductor cables in an uncovered tray are sized by the normal Article 310 ampacity rules. Where the tray is covered for more than 6 ft continuously , the allowable ampacity may not exceed 95 percent of the tabulated value, because the cover traps heat.

The tray as an equipment grounding conductor (392.60)

A metallic cable tray may serve as the EGC, but only where all of the following are true:

The tray sections and fittings are identified for grounding purposes .

The minimum cross-sectional area of the tray conforms to Table 392.60(A) for the largest upstream overcurrent device.

All tray sections and fittings are legibly and durably marked with the letters "EGC" or an equivalent.

The system is in an industrial establishment with qualified persons providing continuous maintenance and supervision .

In ordinary commercial premises wiring, none of that is satisfied, so an equipment grounding conductor must be run in the tray with the circuit conductors.

  • NEC 300.5 — Underground Installations
  • Minimum cover, Table 300.5(A)

Cover is defined as the shortest distance measured between a point on the top surface of any direct-buried conductor, cable, conduit, or raceway and the top surface of finished grade , concrete, or similar cover. Finished paving counts toward cover.

Location Direct burial RMC / IMC Nonmetallic raceway, EMT, other approved raceway 120 V or less residential branch circuit, GFCI, max 20 A OCPD Irrigation / landscape lighting, max 30 V

All locations not specified below 24 in. 6 in. 18 in. 12 in. 6 in.

In trench below 2 in. thick concrete or equivalent 18 in. 6 in. 12 in. 6 in. 6 in.

Under a building In raceway only 0 0 In raceway only In raceway only

Under streets, highways, roads, alleys, driveways, parking lots 24 in. 24 in. 24 in. 24 in. 24 in.

One- and two-family dwelling driveways and outdoor parking, dwelling-related use only 18 in. 18 in. 18 in. 12 in. 18 in.

In or under airport runways, including adjacent restricted areas 18 in. 18 in. 18 in. 18 in. 18 in.

Two rows carry most of the exam weight. The "all locations not specified" row is the default that answers a plain backyard question. The streets and public parking row flattens every column to 24 in. — there is no reduced value for RMC there, which is exactly the contrast the exam likes to draw against the 6 in. figure on the first row.

A 2023 NEC change added electrical metallic tubing to column 3 , alongside nonmetallic raceways listed for direct burial. If you are working from a 2020 book, EMT is missing from that column.

The rest of 300.5

300.5(B) Wet locations — the interior of an underground raceway is a wet location , so conductors must be listed for wet locations: THWN-2, XHHW-2, RHW-2 , or similar. THHN alone does not qualify. Nearly all modern building wire is dual-rated THHN/THWN-2, which is why this passes unnoticed in the field but still gets tested.

300.5(C) Under buildings — underground wiring under a building must be in a raceway that extends past the outside walls.

300.5(D) Protection from damage — direct-buried conductors emerging from grade must be protected by enclosures or raceways from the required cover depth or 18 in., whichever is less , up to a point 8 ft above finished grade .

300.5(E) Splices and taps — direct-buried cable or conductors may be spliced or tapped without a splice box , provided the splice uses methods identified for the purpose.

300.5(F) Backfill — backfill may not contain large rocks, paving pieces, or corrosive material that could damage the wiring; granular fill or protective boards are used where needed.

300.5(I) — all conductors of the same circuit, including the grounded conductor and any equipment grounding conductors, must be in the same raceway or trench .

300.5(J) — where subject to earth movement, direct-buried conductors must be arranged with S loops or expansion fittings to relieve strain.

300.5(K) — a bushing or terminal fitting is required where a direct-buried cable enters a raceway from the earth.