Study guide
8.1 Wiring Methods and Raceways
Texas Journeyman Electrician License Exam Exam
Track your progress as you read
Finished sections get a check mark.
1 Introduction & Exam Overview
1.1 About the Texas Journeyman Electrician Exam 1.2 The Two-Part Exam Format (Knowledge + Calculations) 1.3 Eligibility, Application & Scheduling
2 NEC Structure & Navigation
2.1 Key NEC Definitions (Article 100) 2.2 How the NEC is Organized 2.3 NEC Index and Quick Lookup Strategies 2.4 Reading Electrical Plans, Symbols, and Schedules
3 Electrical Theory & Fundamentals
3.1 Ohm's Law, Power, and Series/Parallel Circuits 3.2 Conductors, Resistance, and Voltage Drop 3.3 Three-Phase Systems and Power Factor
4 Services & Service Equipment
4.1 Service Entrance Conductors and Service Point 4.2 Service Disconnecting Means 4.3 Grounding Electrode Systems for Services 4.4 Service Load Calculations
5 Separately Derived Systems & Feeders
5.1 Separately Derived Systems 5.2 Feeder Sizing, Ampacity, and Tap Rules 5.3 Feeder Load Calculations
6 Branch Circuits & Receptacles
6.1 Branch Circuit Sizing and Conductor Selection 6.2 Receptacle Spacing and Required Outlets 6.3 GFCI and AFCI Requirements 6.4 Lighting Outlets and Switch-Controlled Circuits
7 Overcurrent Protection
7.1 Overcurrent Principles and OCPD Types 7.2 Small-Conductor and Continuous-Load Rules 7.3 Motor Overcurrent and Short-Circuit Protection
8 Wiring Methods, Conductors & Boxes
8.1 Wiring Methods and Raceways 8.2 Conductor Insulations and Ampacity 8.3 Conduit and Raceway Fill 8.4 Boxes and Box Fill 8.5 Cable Trays and Underground Wiring 8.6 Cabinets, Cutout Boxes, and Panelboards
9 Equipment Grounding & Bonding
9.1 Equipment Grounding Conductors 9.2 Bonding & the Effective Ground-Fault Current Path 9.3 Equipment and Box Grounding Connections
10 Equipment, Devices & Transformers
10.1 Luminaires and Lighting (NEC Article 410) 10.2 Switches and Device Wiring (NEC Articles 404 & 400) 10.3 Appliances and Utilization Equipment (NEC Articles 422 & 424) 10.4 Transformers (NEC Article 450) 10.5 Working Space and Equipment Access (NEC 110.26)
11 Motors & Generators
11.1 Motor Branch Circuits & Conductors 11.2 Motor Disconnects, Controllers & Starters 11.3 Generators & Emergency Systems
12 Control Devices & Disconnecting Means
12.1 General Disconnecting Means Principles 12.2 HVAC and Refrigeration Disconnects 12.3 Motor Control Circuits and VFDs
13 Dwelling Load Calculations
13.1 General Lighting and Receptacle Load 13.2 Appliance, Range, and Dryer Load 13.3 Neutral Load and Service Sizing
14 Commercial & Advanced Calculations
14.1 Commercial Lighting and Receptacle Load 14.2 Continuous Loads and Equipment Demand 14.3 Voltage Drop and Conductor Sizing 14.4 Commercial Building Load Capstone
15 Special Occupancies & Conditions
15.1 Hazardous (Classified) Locations — NEC Articles 500–506 15.2 Health Care Facilities — NEC Article 517 15.3 Pools, Spas, and Fountains — NEC Article 680 (Beyond GFCI) 15.4 Other Specific Occupancies — A Survey 15.5 Data Processing Rooms and Communications Systems
16 Renewable Energy Technologies
16.1 Solar PV Systems (Article 690) 16.2 Energy Storage and EV Charging (Articles 706, 625)
17 Exam Strategy & Final Review
17.1 Time Management and NEC Lookup Speed 17.2 Test Day and Final Practice
8.1 Wiring Methods and Raceways
Key Takeaways Explain This Topic AI
NEC Article 300 is the umbrella for all wiring methods: 300.3(A) requires all conductors of the same circuit in the same raceway, 300.4 mandates a 1-1/4 in. edge distance or steel plate, 300.17 makes the lowest insulation temperature govern, and 300.22 restricts plenum installations
Raceway article numbers to memorize: RMC=342, IMC=344, EMT=358, FMC=350, ENT=362, RTRC=353, PVC=352, LFNC=356
Rigid PVC (Article 352) is prohibited in hazardous classified locations (352.12), cannot support luminaires, and requires Schedule 80 where subject to physical damage
FMC (Article 350) may serve as an equipment grounding conductor only for runs not exceeding 6 ft (350.60)
Trade sizes pair with metric designators: 1/2 in.=16, 3/4 in.=21, 1 in.=27, 1-1/4 in.=35, 1-1/2 in.=41, 2 in.=53; minimum raceway trade size is 1/2 in. (metric 16)
Last updated: August 2026
Why Wiring Methods Matter on the TX Journeyman Exam
Wiring methods and materials make up one of the heaviest content areas on the NEC Knowledge portion of the Texas Journeyman exam — roughly 15 to 20 percent of the 59 knowledge questions. Article 300 sets the universal rules for how conductors are installed and protected; Articles 342 through 362 define each raceway type and where it may and may not be used. Expect code-knowledge questions such as "Which raceway is prohibited in a Class I, Division 1 location?" and scenario questions that require you to identify the correct installation method or minimum clearance.
Article 300 — General Requirements for Wiring Methods
NEC Article 300 applies to all wiring installations unless a specific article modifies it. The most-tested subsections on the Journeyman exam are below.
300.3(A) — All Conductors of the Same Circuit in the Same Raceway
All conductors of the same circuit — including the grounded (neutral) conductor and the equipment grounding conductor (EGC) — must be run in the same raceway, trench, cable, or cord. Running the hot and neutral in separate conduits creates magnetic imbalance, inductive heating, and elevated conductor temperature. This is one of the most frequently tested rules.
Exception: Conductors for spark igniters, certain remote-control and signaling conductors under 50 V, and specific parallel conductor installations per 310.10(G) have defined allowances.
300.4 — Protection Against Physical Damage
When raceways or cables pass through structural members, the NEC requires minimum edge clearances or steel plate protection:
Situation Requirement
300.4(A) — Bored holes in wood members At least 1-1/4 in. from the nearest edge of the stud or joist, or protected by a 1/16 in. steel plate
- 300.4(B) — Notches in wood members 1-1/4 in. from edge or steel plate
- 300.4(C) — Metal framing members Listed bushings or grommets to prevent abrasion
- 300.4(D) — Cables through studs 1-1/4 in. edge distance or steel plate
300.4(G) — Insulated fittings at terminations Conductors #4 AWG and larger require a bushing at conduit terminations
The 1-1/4 in. rule is one of the most frequently tested single numbers on the exam — memorize it.
300.17 — Conductors of Different Insulation Ratings
When conductors with different temperature ratings are installed in the same raceway or cable, the lowest temperature rating governs the allowable ampacity of every conductor in the group. If THHN (90 °C) and THW (75 °C) are pulled together, both are limited to the 75 °C column ampacity — even the THHN.
300.22 — Wiring in Ducts, Plenums, and Other Air-Handling Spaces
Article 300.22 restricts what may be installed in spaces that carry environmental air:
300.22(B) — Plenums and ducts specifically fabricated for environmental air: Only listed plenum-rated cable (CMP, CL2P, and similar) or metal raceways (RMC, IMC, EMT, FMC up to 4 ft) and mineral-insulated cable are permitted. Nonmetallic conduit is not allowed.
300.22(C) — Other spaces used for environmental air (for example, the area above a suspended ceiling used as a return-air plenum): Wider allowances — MC cable, AC cable, NM cable, and most raceways are permitted when installed per their respective articles.
Exam tip: plenums under 300.22(B) are far more restrictive than other spaces used for environmental air under 300.22(C). Know the difference.
Raceway Types — Comparison
The NEC organizes each raceway in its own article (342 through 362). Every article has a "Uses Permitted" and a "Uses Not Permitted" section — these are the exact subsections the exam references.
Raceway NEC Article Type Key Uses Permitted Key Prohibitions
RMC (Rigid Metal Conduit) 342 Rigid metal All atmospheric conditions; hazardous locations; direct burial Subject to severe physical damage unless protected
IMC (Intermediate Metal Conduit) 344 Rigid metal Same as RMC; thinner wall, lighter weight Same general restrictions as RMC
EMT (Electrical Metallic Tubing) 358 Thin-wall metal Where not subject to severe physical damage; concealed or exposed Not where subject to severe physical damage (358.12(B)); not in hazardous locations unless Chapter 5 permits
FMC (Flexible Metal Conduit) 350 Flexible metal Where flexibility is required; motor connections; luminaires Not in hoistways; not where subject to physical damage; as EGC limited to 6 ft (350.60)
ENT (Electrical Nonmetallic Tubing) 362 Flexible nonmetallic Concealed in walls and floors; wet or damp where listed Not in hazardous locations; not where subject to physical damage; not above 50 °C ambient
RTRC (Reinforced Thermosetting Resin Conduit) 353 Rigid nonmetallic Underground; corrosive and wet locations; exposed where listed Not in hazardous locations unless Chapter 5 permits
Rigid PVC (Schedule 40 and 80) 352 Rigid nonmetallic Underground; wet and corrosive locations; Schedule 80 where subject to physical damage Not in hazardous locations (352.12); not for luminaire support; ambient temperature limits
LFNC (Liquidtight Flexible Nonmetallic Conduit) 356 Flexible nonmetallic Wet locations; outdoors; direct burial where listed; flexibility Not in hazardous locations unless Chapter 5 permits; length restrictions per 356.12
Trade Size vs. Metric Designator
The NEC uses trade sizes (inches) alongside metric designators . You will see both on the exam. Memorize the common pairings:
- Trade Size Metric Designator
- 1/2 in. 16
- 3/4 in. 21
- 1 in. 27
- 1-1/4 in. 35
- 1-1/2 in. 41
- 2 in. 53
The metric number is the nominal outside diameter in millimeters, rounded. Trade sizes smaller than 1/2 in. (metric 16) are not permitted for most raceway wiring methods — each raceway article sets a minimum trade size of 1/2 in.
Where Each Raceway Is Prohibited — Exam Favorites
PVC (Article 352): Not permitted in hazardous (classified) locations (352.12) except as Chapter 5 allows. Not used to support luminaires. Schedule 80 may be used where subject to physical damage; Schedule 40 may not.
EMT (Article 358): Not permitted where subject to severe physical damage (358.12(B)). Minimum trade size is 1/2 in.
FMC (Article 350): Not permitted as the sole equipment grounding conductor for runs exceeding 6 ft (350.60). Not in hoistways or where subject to physical damage.
ENT (Article 362): Not permitted in plenums (300.22(B)), not in hazardous locations, not where subject to physical damage, and not in ambient temperatures above 50 °C.
LFNC (Article 356): Total length must not exceed 6 ft in a single run unless specifically permitted; not in hazardous locations unless Chapter 5 allows.