Study guide
7.2 Gas Detection, Carbon Monoxide Detection and Special-Application Devices
Texas Fire Alarm Installer License Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Texas Insurance Code Chapter 6002 Foundations
1.1 Chapter 6002 Purpose, Scope & Statutory Definitions 1.2 State Preemption and the Limits of Local Regulation 1.3 Commissioner and SFMO Authority; Adopted Standards and Editions 1.4 Activities Not Regulated: The § 6002.155 Exemptions 1.5 Required Device Labels, Listings and Consumer Information
2 Chapter 2: Certificates of Registration and Company Operating Rules
2.1 Registration Certificates: Main Office, Branch Office and Single Station 2.2 Insurance Requirements for Registered Firms 2.3 Business Location, Designated Employee and Vehicle Identification (§ 34.610) 2.4 Ownership Changes, Officer Changes and Revised Certificates
3 Chapter 3: Individual Licenses, Qualifying Tests and Renewal
3.1 The Six Texas Fire Alarm Licenses and What Each May Do 3.2 License Applications, Fingerprinting and Criminal History 3.3 The Qualifying Tests: TFM11, TFM12, TFM13, TFM14 and Their References 3.4 NICET, ESA and Professional Engineer Substitutions 3.5 Fees, the Two-Year Renewal Cycle and Late Renewal 3.6 Training Schools, Instructors and the Residential Technician Course
4 Chapter 4: Texas Field Practice — Installation, Service, Monitoring and Certification
4.1 Sales, Installation and Service Rules (§ 34.616) 4.2 Monitoring Requirements for Registered Firms (§ 34.616(c)) 4.3 The Installation Certificate (SF035) and Its Distribution 4.4 The Three-Stage Installation Inspection (§ 34.618) 4.5 Fire Alarm Plans and Record Drawings (§ 34.619)
5 Chapter 5: Texas Labels, Records and Enforcement
5.1 Installation and Service Labels (§§ 34.620–34.621) 5.2 Inspection/Test, Yellow and Red Labels and Impairment Notice 5.3 The Texas Recordkeeping and Retention Map 5.4 Prohibited Practices, Discipline, Enforcement and Penalties
6 Chapter 6: NFPA 72 Fundamentals, Power, Signals and Pathways
6.1 Identifying the Applicable NFPA Standards for TFM12 6.2 NFPA 72 Scope, Organization & Core Life Safety Definitions 6.3 NFPA 72 Documentation and Personnel Qualifications 6.4 Types of Equipment and Circuits: IDC, NAC, SLC and System Architectures 6.5 Signal Priority, Annunciation and Monitoring Integrity 6.6 Primary & Secondary Power Supply Calculations 6.7 Principles of Electricity and Notification Circuit Voltage Drop 6.8 Initiating & Notification Circuit Pathways (Class A, B, N, X) 6.9 Pathway Survivability, Shared Pathways and Circuit Separation
7 Chapter 7: Initiating Devices and Detection
7.1 Smoke, Heat & Flame Detection Principles & Spacing Rules 7.2 Gas Detection, Carbon Monoxide Detection and Special-Application Devices 7.3 Detector Selection and Environmental Limits 7.4 Duct Smoke Detectors, HVAC Controls & Specialized Sensors 7.5 Manual Fire Alarm Boxes, Waterflow Switches & Supervisory Initiating Devices 7.6 Sprinkler, Suppression and Releasing Service Interface
8 Chapter 8: Notification Appliances, Emergency Communications and Control Functions
8.1 Audible Notification Requirements & Sound Level Standards 8.2 Visible Notification Spacing, Synchronization & Candela Ratings 8.3 Emergency Communications Systems & Mass Notification Integration 8.4 Emergency Control Functions: Elevators, HVAC, Doors and Egress 8.5 Protected Premises Systems and the Sequence of Operation
9 Chapter 9: Wiring Methods, Supervising Stations and Inspection, Testing and Maintenance
9.1 NEC Article 760 Wiring Methods, Cable Classes & Circuit Protection 9.2 NEC Article 300 Wiring Methods and Installation Workmanship 9.3 Supervising Station Monitoring Systems & Signal Transmission Methods 9.4 Public Emergency Alarm Reporting Systems and Auxiliary Systems 9.5 Periodic Inspection, Testing & Impairment Procedures 9.6 System Acceptance Testing, Commissioning & Maintenance Records
7.2 Gas Detection, Carbon Monoxide Detection and Special-Application Devices
Key Takeaways Explain This Topic AI
Carbon monoxide notification uses the four-pulse temporal pattern (Temporal-4), which is deliberately different from the three-pulse Temporal-3 fire evacuation pattern.
Gas detection connected to a fire alarm system produces the signal type the design assigns — alarm, supervisory or trouble — and NFPA 72 requires that the signal be distinctive and identified.
Gas detectors are the one detector family that generally requires periodic calibration against a known test gas rather than functional smoke or heat entry testing.
Video image smoke and flame detection uses processed camera imagery, is treated as a listed detection method, and must meet the same monitoring-integrity and annunciation requirements as any other initiating device.
Detectors of any type must be listed for the purpose and installed within the environmental limits of their listing; a device installed outside its listed range is not code compliant regardless of how well it appears to work.
Last updated: August 2026
Why This Section Matters
Modern commercial systems monitor more than fire. Carbon monoxide detection is now common in hotels, schools and multifamily buildings; combustible gas detection appears in mechanical rooms and kitchens; and video image detection shows up in atria and warehouses. Each of these introduces a signal that must be distinguishable from a fire alarm, and TFM12 tests the distinctions.
- 1. Carbon Monoxide Detection
- The distinctive pattern
Hazard Audible pattern Structure
Fire evacuation Temporal-3 (T3) 0.5 s on, 0.5 s off, 0.5 s on, 0.5 s off, 0.5 s on, then 1.5 s off — a 4-second repeating cycle
Carbon monoxide Temporal-4 (T4) Four short pulses followed by a 5-second pause, then repeat
The two patterns exist so an occupant can tell the difference between "leave the building" and "you are being poisoned by an odorless gas." Never program a CO input to sound the fire evacuation signal, and never program a fire input to sound T4.
Design and placement principles
CO alarms and CO detectors must be listed for the purpose, and installed per the manufacturer's published instructions and the applicable code that mandates them.
CO detection is usually driven by the building or fire code — not by NFPA 72 — which decides which occupancies require it and where.
CO signals are normally routed as a distinct signal type at the control unit, with distinct annunciation. Where a system serves both fire and CO, the annunciator and the record drawings must make the distinction obvious to responders.
CO sensing elements have a finite service life marked by the manufacturer; replacement at end of life is a maintenance obligation, not an optional upgrade.
2. Combustible and Toxic Gas Detection
Gas detection connected to a fire alarm system is treated as an initiating function. Three design decisions must be made explicitly and documented in the sequence of operation:
Decision Options Typical choice
Signal type Alarm, supervisory, or trouble Often supervisory for a low-level gas condition and alarm for a high-level condition
Outputs driven Notification appliances, ventilation start, fuel shutoff, equipment shutdown Frequently ventilation and shutoff without general evacuation
Annunciation Distinctive indication identifying gas rather than fire Required so responders do not treat a gas event as a structure fire
Sensor technologies you should be able to name:
Technology Principle Common use
Catalytic bead Combustion of gas on a heated catalytic element changes resistance Combustible gases in the lower-explosive-limit range
Electrochemical cell Target gas reacts at an electrode producing a current CO, H₂S, and other toxic gases at low concentration
Infrared (NDIR) Absorption of a specific IR wavelength by the target gas Hydrocarbons and CO₂; immune to catalyst poisoning
Semiconductor (metal oxide) Gas adsorption changes surface conductivity Low-cost broad detection; less selective
Calibration, not smoke entry
This is the operational difference that most often appears on a test. A smoke detector is tested by introducing smoke or listed aerosol; a heat detector by heat or a listed method. A gas detector is verified by applying a known concentration of test gas and confirming the response, at the interval and by the method in the manufacturer's published instructions. Sensor elements drift and have a defined service life , so calibration records and replacement dates belong in the ITM file.
3. Video Image Smoke and Flame Detection
Video image detection analyzes camera imagery with software to identify the visual signature of smoke movement or flame flicker. Under NFPA 72 it is a legitimate detection method when the equipment is listed for the purpose, and it is subject to the same fundamentals as any other initiating device:
The pathway between the imaging device, the processing equipment and the control unit must be supervised , with faults annunciated within 200 seconds .
The design must document field of view , obstructions, lighting conditions and minimum illumination in the record drawings and the sequence of operation.
Periodic testing must confirm actual detection performance, not merely that the camera produces a picture.
Changes to the space — new racking, a new partition, altered lighting — can invalidate the detection zone and must be re-evaluated, exactly as a relocated wall invalidates strobe coverage.
4. Other Special-Application Detection You Should Recognize
Device Principle Where it appears
Projected beam smoke detector A transmitted light beam is attenuated by smoke between transmitter and receiver Atria, warehouses, high open spaces where spot detectors are unreachable
Air sampling (aspirating) detection A fan draws air through a sampling pipe network to a highly sensitive detection chamber Very early warning in data centers, clean rooms, cold storage
Line-type heat detection A cable whose insulation fails at a rated temperature, shorting two conductors Cable trays, conveyors, tunnels, parking structures
Radiant energy (flame) detection UV, IR, UV/IR, or multi-spectrum IR sensing of flame emissions Hangars, petrochemical, high-hazard open areas
Duct smoke detection Sampling of duct airflow HVAC shutdown per NFPA 90A — see the duct detector section
The unifying rule: every one of these must be listed for the application , installed within its listed environmental limits, and tested by a method appropriate to the technology. A device outside its listed temperature, humidity, or air-velocity range is non-compliant even if it appears to function.
5. Worked Fact Patterns
Pattern A. A hotel installs CO detection in guest rooms and the integrator programs the CO input to sound the building evacuation signal.
→ Wrong. CO notification uses the Temporal-4 pattern, deliberately distinct from the Temporal-3 fire evacuation pattern, so occupants can distinguish the two hazards and respond correctly.
Pattern B. A mechanical room combustible-gas detector is wired to a monitor module and programmed to sound general evacuation on any detection.
→ Question the design. The signal type, outputs and annunciation are design decisions that must appear in the sequence of operation. Low-level gas commonly drives a supervisory signal with ventilation and fuel shutoff, without general evacuation.
Pattern C. A technician "tests" a catalytic bead gas detector by pressing its magnet-actuated test button and records a pass.
→ Insufficient. Gas detectors require verification with a known test gas at the manufacturer's specified interval, because sensing elements drift and have a defined service life.
Pattern D. A warehouse installs video image smoke detection and later adds 20-foot racking that blocks half the camera's field of view.
→ The detection zone is compromised. The change must be re-evaluated, the record drawings and sequence of operation updated, and — in Texas — the modification documented under §§ 34.617 and 34.619.